KPLED ACS15A RF Smart AC Switch Instruction Manual

KPLED ACS15A RF Smart AC Switch

Specifications

• Model No.: ACS15A
• Features: RF AC Switch / Push off / Relay output / Zero-crossing detection
• Input and Output:
  • Input voltage: AC100-240V
  • Output voltage: AC100-240V
  • Output current: 15A (Resistive load), 10A (Inductive load)
  • Output power: 1500-3600W
  • Relay surge current: 120A (20ms)
• Input signal: RF 2.4GHz + Push switch
• RF Control distance: 30m (Barrier-free space)
• Safety and EMC:
  • EMC standard: ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4
  • Safety standard: EN 62368-1:2020+A11:2020
  • Certification: CE, EMC, RED
• Warranty: 2 years
• Environment:
  • Operation temperature: -30°C to +55°C
  • Case temperature (Max.): +85°C
  • IP   rating: IP20
  • Package Size: L60 x W60 x H40mm
  • Gross weight: 0.061kg

Product Usage Instructions

Mechanical Structures and Installations

Users can choose the suitable match/delete ways.

Two options are offered for selection:

1. Use the Match key: Short press the match key, and immediately press the on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
2. Use Power Restart: Switch off the power, then switch on the power, and repeat, Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means the match is successful.
3. Delete: Press and hold the match key for 10s to delete all matches, The light blinks 5 times means all matched remotes were deleted.
4. Delete: Switch off the power, then switch on the power, and repeat, Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

Wiring Diagram

Self reset switch: Short press, turn on the light; Short press again, turns off the light.

Note: The MAX. surge current of the switch is 120A. When connecting multiple capacitive (LED power supplies) or inductive loads, the sum of the surge currents cannot exceed its maximum value. Otherwise, long-term use may cause product damage.

Frequently Asked Questions

Q: Can this product be used with dimmable LED lamps?

A: No, this product is a non-dimming switch designed for single-color LED lamps, traditional incandescent, and halogen lights.

Q: What is the range of the RF control distance?

A: The RF control distance is approximately 30 meters in a barrier-free space.

RF AC Switch / Push on-off / Relay output / Zero-crossing detection

Features

• RF + AC push smart switch, without dimming function.
• To switch single color LED lamps, traditional incandescent and halogen lights.
• Compatibility with RF 2.4G dimming remote control.
• Connect with external push switch optional.
• High-inrush specification relays (normally open).

Technical Parameters

Input and Output

Input voltage| AC100-240V
Output voltage| AC100-240V

Output current

| 15A (Resistive load) 10A (inductive load)
Output power| 1500-3600W
Relay surge current| 120A (20ms)
Input signal| RF 2.4GHz + Push switch
RF Control distance| 30m (Barrier-free space)

Safety and EMC

EMC standard(EMC)| ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4

---|---
Safety standard| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE, EMC, RED
Warranty
Warranty| 2 years
Environment

Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| Tc: +85 OC
IP rating| IP20
Package
Size| L60x W60 x H40mm
Gross weight| 0.061kg

Mechanical Structures and Installations

Installation method

Note:

1. The installation must be installed or removed by a professional electrician.
2. Please keep the device out of the reach of children.
3. Please keep away from water, humid or hot environments.
4. The device should be kept away from strong signal sources (such as microwave ovens) to avoid signal interruption and cause the device not to work properly.
5. Avoid placing the device close to or near high-density materials (such as metal, concrete walls, etc.), which will reduce or block the wireless signal.

Match RF remote control

• Users can choose the suitable match/delete ways.
• Two options are offered for selection.

Use the Match key Match:

• Short press the match key, and immediately press the on/off key (single zone remote) or zone key (multiple zone remote) on the remote.

Delete:

• Press and hold the match key for 10s to delete all matches, The light blinks 5 times means all matched remotes were deleted.

Use Power Restart Match:

• Switch off the power, then switch on power, repeat, Immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote.
• The light blinks 3 times means the match is successful.

Delete:

• Switch off the power, then switch on the power, repeat, Immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote.
• The light blinks 5 times means all matched remotes were deleted.

Wiring diagram

Self reset switch:

• Short press, turn on the light;
• Short press again, and turn off the light.

Note:

• The MAX. surge current of the switch is 120A.
• When connecting multiple capacitive (LED power supplies) or inductive loads, the sum of the surge currents can not exceed its maximum value.
• Otherwise, long-term use may cause product damage.

Available RF remote

Application Description

1. All receivers in the same area are controlled synchronously.

RF remote

Automatic transmission:

• The receiver transmits the remote control signal to another receiver (within 30m), and when the remote control signal is not strong, a signal amplifier can be used to extend the Wireless control distance.

Automatic synchronization:

• The same remote control can synchronously control multiple receivers within a distance of 30;
• The receiver MAX. remote control distance is 30m, but strong signal sources such as reinforced concrete walls, metal materials, WiFi routers, and microwaves will shorten the remote control distance;
• For indoor applications, it is recommended that the receiver be placed no more than 15 meters away.
• It is recommended not to have too many receivers controlled by a remote control to avoid interference between remote control signals.
• Each receiver (one or more) is located in a different area, such as Zone 1, 2, 3, or 4, with zone control.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>