Shenzhen Zhongyou Hulian Technology ZYHL-2003 Solar WiFi Camera User Guide
- June 6, 2024
- Shenzhen Zhongyou Hulian Technology
Table of Contents
Shenzhen Zhongyou Hulian Technology ZYHL-2003 Solar WiFi Camera
Packing list
(please refer to the actual product)
Camera
|
Solar
panel
|
Bracket
---|---|---
Certificate of conformity
|
Accessory package
|
Manual
Schematic diagram of interface description
Download and install the APP
- Scan the QR code below and click to install or open the mobile app market to search for Tuya Smart.
Sign up for Login Account
-
Enteryour mobile phone number or email address.
-
Enter the verification code and set the password, then click login.
Device connection
Note: This device has built-in battery pack. For the first use,please use the DC SV2A with USB cable to charge for 10 hours.
-
Button:
Reset button and On/Off button:
① In the off state, long press for 4 seconds to power up.
② In the boot state,long press for 5 seconds to reset.
③ In the bootstate,long press for 10 seconds to power off. -
Indicator light:
The red light keeps flashing : Wait to connect to the network.
The red lights always on: In error state, please restart.
The red light keeps flashing : The Network connection is in progress.
The blue lights always on: The device is successfully connected.
If record ing is needed,please insert the SD card ( (the chip of SD card is \ facing the USB interface) then wait for a beep and the red light flash ing. -
Please open the APP as follows:
① Click on “+”.
② Click “Scan Code”.
③ Scan the QR code on the device.
④ Click on “Add”.
⑤ Click on “Next”.
⑥ Make sure the device’s indicator led flashes and you hear the beep, then click “Next”.
(If not, the device is in an error state.Please press the reset button for 5 seconds. At this time, the indicator led flashes and gives a prompt sound, indicating that the device is reconfigured.)
⑦ Click on “Next”
⑧ Enter WiFi account & password, then click “Next”.
⑨ Aim the phone’s QR code at the device and keep a distance of 15-20cm.APP will auto-complete the device configuration and issue a prompt sound after identifying the QR code.Then click “I Heard a Prompt”.
⑩ The device is being added.
⑪ Congratulations! The device is connected.
-
Switching and connection of the AP mode.
① Open the APP monitoring screen and click the 3 dots in the upper right corner.
② Find and click “AP Mode”.
③ Set a password with at least 8 digits, then click “Start AP Mode”.
④ The AP mode is enabled successfully, then click”connect”.
⑤ Find the WiFi name” Tuya-lPC”, click it to enter the password you just set,
and click Connect.
⑥ After successful connection, it shows that the current WIFI is unavailable.
Do you want to continue using this WIFI? Click Use.
⑦ Click back to the APP to see the live screen.
⑧ If you need to exit AP mode, shut down the device and restart it.
- A few reminders about the PIR humanoid detection feature.
-
The humanoid detection sensitivity can be set in the device setting.
When used in a crowded environment, it is recommended to turn off or set the device to low sensitivity to avoid unnecessary wake-up to prolong the battery service time. -
- Off: In this state, the device will not perform humanoid detection .
-
Low: When the device is in hibernation state, it can sense movement detection within 5 meters and trigger to report.
-
Middle: When the device is in hibernation state it can sence movement detection.
Equipment instructions
① Support binding third-party software Alexa and Google to wake up the device.
② View alarm messages.
*Click on Message Notification to view the device’s alarm message.
③ Check the video playback.
Click “Playback” then select the date to view all the files and videos of the
day.
Matters needing attention
① PIR is sensitive to cold and hot disturbance, points should be noted during
installation:
Avoid placing the device in places where the air is churning. For
example: air conditioning outlet, equipment cooling outlet, fan surrounding,
curtain nearby, etc.
Do not install the device directly in front of the glass or mirror.
The recommended installation height of the device is about 2.5m-3m.
Do not invert the device.
② The device supports battery power, and the battery’s service time is
affected by the wake-up time and frequency of the device.So the human
detection function is suggested to turn off or set the device to low
sensitivity when used in a crowded environment, so as to reduce the wake-up
times of the device and extend the application time.When the device is low in
power, please charge it in time. If the battery is underpowered for a long
time, it may cause battery failure.
③ During the installation of the device, please ensure that the WIFI network
signal is stable at the installation location,especially outdoors.Please check
whether the WIFI is covered. If the WIFI signal is weak, a WIFI router should
be added to improve the signal.
④ The device is a low-power intelligent product, which can support APP remote
wake up, PIR human detection wake up, button wake up.Each time the wake-up
device works, it will automatically enter the sleep state after a short time.
⑤ To ensure that the device can work normally, please first use the original
DCSV2Achargerwith USB cable to charge for 10 hours. Do not use a mobile power
supply to charge, otherwise it is very likely to cause a short circuit.
⑥ The device supports WiFi 2.4GHz but does not supportWiFi 5GHz.
Troublesshooting
① Network allocation failed:
- Check if the camera is in the configuration state.
- Please make sure that the phone, camera and router are close enough.
- Note that this camera does not support 5GHz routers.
- Check whether the router name and password are correct.
② The device is offline:
- Check the internet connection of the router.
- Check the connection between the router and the camera. If you change the router or modify the WIFI password, you need to reset the camera and reconfigure the network.
- Check if the camera battery is exhausted, you can try to plug in the USB power source and try again .
③ Unable to preview:
- The server may be congested, you can try to restart the APP and try again.
④ No news push:
- Please make sure that the APP has notification permissions.
- Please make sure to turn on the alert message button in the APP personal center settings.
- Please make sure the PIR switch in the camera settings is turned on.
⑤ No video files:
- Please insert the SD card before powering on.
- Please make sure that the PIR switch of the camera is turned on.
- Please makesurethatthecamera recording switch is turned on.
- Please check whether the SD card status in the APP device is normal, if it abnormal, please try to format the SD card.
Common Problems
Q: Why does the battery drain so fast?
A: Frequent triggering of the human detection function in a crowded
environment can cause the device to work for a long time and consume power
easily.Please try to lower the PIR sensitivity setting;
Long time to view video playback file, easy to consume power;
Check whether the device signal is stable. If the network is not normal, the
device may wake up multiple times and consume power easily. Please try to
change the position of the device or change the SIM operator.
Q: How can I confirm that the camera is connected properly?
A: Please try to actively trigger PIR, wait for 3 seconds, the blue light
is on, indicating that the device is connected properly.
