Xiamen Weitrui Electronic Technology VTR-TB41 Thermal Label Printer User Guide
- June 6, 2024
- Xiamen Weitrui Electronic Technology
Table of Contents
105x150mm
Thermal Label Printer
quick start guide
Operation Manual
(Ver 1.0)
Safety instructions
Attention
- The printer should be installed in a flat, stable place;
- Leave enough space around the printer to operate and maintain;
- The printer should stay away from the water and avoid direct sunlight, strong light, and heat source.
- Do not use and save printers in high temperatures, humidity, and pollution.
- Avoid placing the printer in a place where there are vibrations and shocks;
- Connect the power adapter of the printer to an appropriate grounding socket to avoid using the same socket with the large motor or other equipment that can cause the power voltage fluctuation.
- If the printer is not used for a long time, please disconnect the power of the printer power adapter.
- To ensure print quality and product life, recommended or equivalent quality paper Is recommended.
- When the Interface is plugged or disconnected, the power supply must be turned off, otherwise the printer control circuit may be damaged. 10) The user shall not disassemble the printer for repair; 11) Keep this manual for reference.
Unpacking list
Characteristics and Performance
-
1.1 Printing
Method: Thermal Directly -
Width: 110mm ± 0.5mm
-
Resolution: 203 dpi (8dotimm)
-
Speed: Max150mmis
-
Reliability
Printer head life: 50km
Working conditions:
Printing 12×24 Western characters, 50 lines at a time, and repeating intermittently.
Pruning no more than 25% of each line at the same time, and no more than 11 vertical reprints of each character at the same dot.
*Using appointed label paper -
Printing widtb:108± 0.2mm 1.2 Printing Paper
-
Label paper model
-
Label paper width:110mm ± 0.5mm 1.3 Printing character
-
ANK character 12x24dot 1.5 (W) x3.0 (H) mm
-
National standard one,Second-level Chinese character library 24x24dot 3.0 (W) x3.0 (H) mm 1.4 Interface
-
USS 1.5 Printing control command
Support CPCLATSPL \JPL instruction
1.6 Power supply
- DC24V ± 10%, 3.0A
- 1.7 Working environment
- Operation environment: -10—+50°C Relative humidity: 10-80%
- Storage environment: -20—+60t Relative humidity: 10-90%
1.8 Dimensions 191. 15(1)x97.3(W)x101(H)mm
4, Operation Instruction
4.1 Printer Body IV)TR-TB41 Windows system download and installation process First, quit the computer all anti-virus software, 360 anti-virus software, KingSoft anti-virus software, etc 4.1. Go to the below link address to download the installation driver
https://www.paperang.com/download/app/driver/TB-41.rar
4.1.4Download installation driver Detailed introduction:
4.1.5 Unzip the installation package 4.1.6Power port, communication
port, power on/off
** 4.1.7Connect the USB cable to the printer 4.1.7Connect the power cable to the printer 4.1.8 Power on/off**
4.1.9 Select USB, and dick installation.
Install successfully
4.2Paper feed
Press1. push button to open the top cover. Feed-in 2. the thermal paper into
the printer. Push 3. media spacers to fix the thermal paper then close the top
cover as shown below picture:
4.3.Se1f-test page printing
4.3.1Self-test page printing
Self-test page printing is shown as below: Press the printing button and turn
on the power button at the same time after the power cable and USB cable are
connected. Then the self-test page can be printed.
4.3.2 Self-test page
4.4lndicator light button and buzzer explanation
4.4.1 With Bluetooth
Power on Blue indicator light blink slowly Paper out: The red indicator light
blinks slowly and the buzzer beeps three times.
Open cover: The red indicator light is always on and the buzzer beeps six
times Bluetooth connection: The blue indicator light is always on
4.4.2 Without Bluetooth
Power on The green indicator light is always on Paper out: The red indicator
light blinks slowly and the buzzer beeps three times. Open cover: The red
indicator light is always on and the blazer beeps six times. The button
displays red light indicates paper out. 4.4.3 Bluetooth Bluetooth support 2.0,
4.0
4.3.1 The button displays a red light
4.3.2 The button displays a green light 5.1 Download APP:
Input the ” print label ” in the search bar on Google Play or App Store
5.2.Input the ‘ print label ‘ in the search bar kindly please reference below picture
5.3. Go to the download status then download and install 5.4 The successful installation icon is shown below
5.5. Create the template kindly please reference the below picture To set the size of the label paper, and click New
5.6.Connect the Bluetooth TB41-U on the printer kindly please reference below picture 5.7. Label printing
6.1../ disk contents
6.1.The WINDOWS driver
6.2.The MAC driver
6.3. Electronic instruction manual
6.4.download and installation driver for guide video
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your b
General Troubleshooting
-
The printer can be printed self-test page, but the installed driver does not work?
A: Please check if the driver is installed correctly or not. If correct, just please check the printer port selection is correct or not. lf all correct, please send it back to the designated maintenance point to repair. -
The printer does not feed the paper out?
A: The movement sensor is dirty, please use a soft brush to clean the sensor, if still can not feed the paper out after cleaning, please send it back to the designated maintenance point to repair. -
The control panel light is not on?
A: Please check the power cord is inserted correctly into the printer and power adapter and power outlet, check the printer power switch Is turned on or not
(or the battery has power or not), if these are all normal, please send them back to the designated repair point to repair -
After the printer is working for a while, the red light is suddenly flashing(have paper roll)?
A: The print head may be overheated, if the print head temperature is too high the printer would be stopped working, just stop printing for a while.if the printer still does not work, please send it back to the designated maintenance point to repair -
If the water gets into the printer, how to do it?
A: Immediately turn off the power, use the hairdryer to dry the motherboard and the movement and other components, of course, please pay attention to the temperature, the temperature can not be too high, the normal temperature should be about 50’C -
The printer can be not run start?
A: The battery may not have any power, please charge it with the factory standard power charger, if still does not work, please send it back to the designated maintenance point to repair. -
Can not search the printer via Bluetooth connection?
A: Please check the equipment “Bluetooth” function is started or not, and the communication is normal or not, and then re-plug the”Bluetooth module” of the printer to have a check, if still not ok, please send it back to the designated maintenance location to repair. -
The print data is missing when the printer is printing in progress?
A: Firstly look at if each label is the same size or not, if not, just replace the label. lf the label is no problem, then it is the machme that failed to detect the paper, need to re-test paper. Re-start the printer to fly again, if there are still problems, please send it back to the designated maintenance location to repair -
The paper can be fed out, but can not print anything on the paper.
A: Check if the paper is put in the opposite direction or paper is not thermal paper, if so, please according to the instructions to put the paper in the correct way -
The paper feeds normally during printing but only can be printed half of content or Printed garbled.
A: Restart the print program-create a new label, reset the layout on the label, select the correct print driver to print to check if it is ok or not. If still not ok. then you can try to uninstall the software and re-install to check. Or you can change another computer to have a try -
The printer runs normally when printing, but the machine does not respond when printing.
A: Check if the interface of the printer is correct to connect or not. and check the port settings of printer drivers are correct or not.Click Start Menu ->Settings- >Printers-> Select printer driver,then check->Properties ->Port -> Select 1.153001 or USBOO2orUSB003 -
The content that prints out is not clear
A: Firstly please check if the pun thread is dirty or not. dirty, please clean the print head (Note: When cleaning the printhead, it must power off the printer first), and then set the next print temperature or change to print another font (bold font), If still not ok. maybe the quality of the label paper is not good, please replace the label paper to have a try -
Not clear when printing and black lines appear
When cleaning the print head. be sure to power off the power of the printer. otherwise
A: Firstly try to clean the print head, if still not ok, have to replace the print head. (Note the print head is easily damaged). -
The printer blinks and does not detect the paper while printing(Zebra machine) Cause.
The sensor is faulty.
A: Clean the dust on the sensor surface or replace the sensor -
When printing a label, some words can be not printed out
Cause: The print head is dirty and the layout is wrong
A: Please clean the print head, And please check if the contents are overlapping when printing, if so. please re-typesetting -
Printing software can not be typesetting.
The reason: the software is not installed or the computer problem.
A: Re-install the software, if still not ok, it may be a virus in the computer, please kill the virus or re-install the operating system. -
in the printing process,the content that printed out is not the same size as the actual content.
A: Choose the correct printer driver. -
Jumping paper often occurs when printing
A: If the paper size and spacing settings are correct, then restart the printer and check if the printer drive Settings are correct or nor.
Daily maintenance of printer
Dirt, foreign objects, sticky substances, or other contaminants that adhere to
the printhead or printer may reduce print quality. When dirty, clean the print
head as follows.
∗ considerations
- Always turn off the printer before cleaning
- The printhead gets very hot due to priming. Therefore, if you want to clean the printhead, turn off the printer and wait for 2 to 3 minutes before starting.
- When cleaning the print head, be careful not to touch the heating part of the print head so as to avoid damage to the head due to static.
- Be careful not to scratch or damage the printhead.
7.1 Clean the printhead
- Open the printer cover and use a cleaning pen (or cotton swab moistened with thin alcohol) to dean it all the way to the center of the printhead.
- After cleaning the printhead, do not use the printer immediately and wait for the alcohol to evaporate completely (1 to 2 minutes) before the printhead is completely dry.
7. 2 Clean sensors, roller, and the paper path
- Open the cover and remove the paper roll.
- Wipe off dust or foreign objects with a dry cloth or cotton swab.
- Soak a cotton cloth or cotton sticks in medical alcohol and use them to remove sticky foreign or other contaminants.
- Do not use the printer immediately after cleaning the parts. Allow the alcohol to evaporate completely (1 to 2 minutes) before the printer Is completely dry. )
∗Clean parts when print quality or paper detection performance is degraded.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>