Shenzhen Aidelong Intelligent Communication W33 Wireless Charger Instructions
- June 6, 2024
- Shenzhen Aidelong Intelligent Communication
Table of Contents
Shenzhen Aidelong Intelligent Communication W33 Wireless Charger
Specification
| Product | Wireless Charger |
|---|---|
| Model | W33 |
| Input | 5V-2A 9V -2.2A |
| Distance | 15W(Max) |
| Output | 6mm (Max) |
| Temperature | C°C-35° |
| Suitable Model | iPhone 12 series |
| Package List | Machine x1, UM x1 |
The parameters are from theoritical design will be different due to different factors The picture is only for reference, please refer to the real object.
Product overview
Charging Distance: Toe distance between the induction coil inside the
mobile Phone and the internal induction coil of wireless charger is 6mm.
Please avoid using thick phone case.
The magnetic coil Inside the mobile phone
Wireless charger internal magnetic Indication call
Usage Scenario description
This magnetic wireless charger is only suitable For the following scenarios. Prease check whether Your mobile phone or phone case is applicable before using
- Naked iPhone12 can be magnetic fixed and wireless charged directly.
- iPhone12 serial with magnetic suction case can be magnetic fixed and wireless charged directly.
- iPhone12 serial with Non- magnetic suction case(the case thickness should be less then 2mm)rcan be wireless charged, but magnetic suction will be weak.
- Other phone (support QI wireless charge) with correct magnetic suction easer can be magnetic fixed and charged directly.
- Other phone (support QI wireless charge) without magnetic suction case, can be wireless charged only when the center of the charger face to the center of the receiver part of the phone. otherwise the phone can’t be charged.
Instructions
Note: The charged devlce must meet the QI standard before use.
-
Insert the USB input interface into the charger or other charging interface and apply power, the wiref ass charger will be standby.
-
Put the wireless charger on the back of the phone, the phone will be magnetic fixad on the phone (if supported) and siart wireless charging.
-
When the wireless charger senses other metal foreign matter, the wireless charger will stop charging and tum to protection mode.
Warnings:
- Make sure your phone supports wireless charging
- Please do not place metal/magnet/credit card on the mobilephone or phone case.it will block the wireless charge
- Do not use the mobile phone case which is more than 0.078 inch thick, otherwise it will not be able to charge
- Do not disassemble, bump.squeeze or put the product into the fire.
- Do not use the product under the condition of the high temperature, humiity or corrosion,so as to avoid electric leakage in the circuit
- Do not splash water or other liquids on the wirless charger. If cleaning is required, make sure the power is disconnected.
- When charging, keep the distance between the implanted medical device (pacemaker, co-chlear implant,etc) and the wireless charger at least 20cm to avoid potential interference to the medical device
- When using the DC charger for power supply,please make sure your charger Support PD charge, and its max power is more than 18W.
- Please keep the product out of the reach of kids.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>