ZASCO G19S Wired Plastic GPS Tracker User Manual
- June 6, 2024
- ZASCO
Table of Contents
ZASCO G19S Wired Plastic GPS Tracker User Manual
Product Functions
NOTED
SIM Card needs SMS, data service and phone call functions.
ACC Detection
Geo-fence
Low Battery Alarm
Trace Playback
Real-time Tracking
Geo-defense
Movement Alarm
SOS Emergency
Remotely Stop Engine
Cut-wire Alarm
Voice Monitoring
Vibration Alarm
Product Parameters & Functions
- Product Parameters
Item| Name| Specification
---|---|---
Main
Features| Size| 80mm (L) 40mm (W) 1 3mm (H)
Weight| 40g
Battery| 240mAh
GPS Chip| MT2503D
GPS| GPS Fixed Time| Hot<2sec (Open Sky)
Warm<15sec
Cold<38sec(Open Sky)
Positioning Accuracy| 5-10m
GSM| GSM Frequency| 850/1900MHz - Accessories list
Item | Unit | Qty |
---|---|---|
Device | Pc | 1 |
SOS | Pc | 1 |
Mic | Pc | 1 |
Relay | Pc | 1 |
Manual | Pc | 1 |
Product Installation
-
Check the device if it’s completed.
-
This device should be inserted into a SIM card which supports 2G GSM network.
-
Connect Wires and Switch on.
-
Red wire to the positive power(+) of vehicle battery, black wire to the negative power(-) of the battery.
-
Device ACC line connect to the acc line of car.
Wire Connection
Line | Connections |
---|---|
Red | to positive power(9-90V) |
Black | to Negative Power |
Orange | to ACC line |
Yellow | to relay |
Red LED Llght(Power/work condition)
State | Meaning |
---|---|
Slow blinking | Normal work (Battery supply power) |
Light on | Normal work (Vehicle supply Power) |
Light off | Device problem or in sleeping |
Yellow LED Light (GSM Signal Light)
State | Meaning |
---|---|
Fast blinking | GSM Initialize |
Slow blinking | GSM normally receive signal |
Light off | No GSM signal or in sleeping |
Blue LED Light (GPS Signal Light)
State | Meaning |
---|---|
Fast blinking | Searching GPS |
Slow blinking | Normal Working |
Light off | No GPS signal or in sleeping |
Installation location
Precautions
GPS Tracker should be installed covertly, please contact the supplier for professional installation advice.
- Hidden installation, avoid water.
- Ensure the Led side facing sky and no metal cover.
- Use cable or 3m tape to fix the device.
Working Description
- After connected with vehicle battery, device will be turned on automatically and power indicator light (red) will be long bright.
- If the device is using its own back up battery, the power indicator light (red) will slowly blink after turned on manually.
- GSM signal light (yellow) and GPS signal light(blue) start fast blinking.
- A few seconds later both GSM light and GPS light will be steady and start slow blinking; device enters into normal working status.
- SOS alarm. Press and hold onto the SOS button for 3 seconds, then the preset SOS numbers will receive phone calls and will be able to hear the sound around the vehicle.
- Voice monitoring. Use preset SOS numbers to call the device, and then the line will be answered automatically after 10 seconds to initiate voice monitoring function.
Trouble Shooting
Problem | Description | Solution |
---|---|---|
Failed to connect the Internet | SIM card not | Check the sim card |
Simcard not installed properly | Install again | |
No GSM network | Move the device in gsm network area | |
Weak GSM network | Move the device in strong GSM network area | |
Location failed | SIM card has no gprs functions | Contact Sim card supplier to |
activate the gprs function
Always reply “failed to get location”| Contact the supplier
No GPS location| Some poor signal areas like basement, tunnels are not able
to acquire GPS signals.| Move the device to open sky areas.
Access to Platform
There are two methods to login in the platform or app.
- Login by IMEI number(the 15 digits in the back of the device), password: the last 6 digits of imei number.
- Contact the supplier to create an account for you.
SMS Command
- Check device state. Format: status#
- Set sos number Format: sos,a,sos number#
- Check location Format: DW or 123
- Set center number Format: center, a, center number#
This Frequency the following Member States or the geographical area within a Member State where restrictions on putting into service or requirements for authorisation of use exist.
(BE: Belgium, BG: Bulgaria, CZ: Czech Republic, DK: Denmark, DE: Germany, EE: Estonia, IE: Ireland, EL: Greece, ES: Spain, FR: France, HR: Croatia, IT: Italy, CY: Cyprus, LV: Latvia, LT: Lithuania, LU: Luxembourg, HU: Hungary, MT: Malta, NL: Netherlands, AT: Austria, PL: Poland, PT: Portugal, RO: Romania, SI: Slovenia, SK: Slovakia, FI: Finland, SE: Sweden, UK: United Kingdom)
Declaration of Conformity
Compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10),This product is allowed to be used in all EU member states.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>