Black Hills Fireplace 6000C-IFT Direct Vent Gas Fireplace Instruction Manual

Black Hills Fireplace 6000C-IFT Direct Vent Gas Fireplace

Specifications

• Models: 6000C-IFT, 6000C-IFTLP, 8000C-IFT, 8000C-IFTLP
• Installation must be performed by a licensed plumber or gas fitter in the Commonwealth of Massachusetts
• Hot glass warning: Do not touch glass until cooled. Keep children away from hot glass.

Product Usage Instructions

1. Installation Standard Work Checklist

Refer to the provided checklist for step-by-step installation guidance.

2. Getting Started

• A. Design and Installation Considerations: Review the design considerations before starting installation.
• B. Good Faith Wall Surface: Ensure a suitable wall surface for mounting.
• C. Tools and Supplies Needed: Gather all necessary tools and supplies for installation.
• D. Inspect Appliance and Components: Check the appliance and components for any damage before installation.

3. Framing and Clearances

• A. Appliance/Decorative Front Dimension Diagrams: Follow the provided diagrams for framing dimensions.
• B. Clearances to Combustibles: Maintain proper clearances to prevent fire hazards.
• C. Constructing the Appliance Chase: Build the appliance chase according to specifications.
• D. Floor Protection: Install suitable floor protection below the appliance.

4. Termination Location and Vent Information

• A. Vent Termination Minimum Clearances: Ensure proper clearances for vent termination.
• B. Vent Terminal Clearances: Maintain clearances around vent terminals.
• C. Approved Pipe: Use only approved pipes for venting.
• D. Use of Elbows: Follow guidelines for using elbows in venting systems.

5. Vent Clearances and Framing

• A. Pipe Clearances to Combustibles: Keep pipes clear of combustible materials.
• B. Wall Penetration Framing/Firestops: Frame wall penetrations correctly with firestops.
• C. Ceiling Firestop/Floor Penetration Framing: Install firestops for ceiling and floor penetrations.
• D. Install Attic Insulation Shield: Place insulation shield in the attic as required.

6. Appliance Preparation

• A. Vent Collar Preparation: Prepare the vent collar for installation.
• B. Installing Optional Heat Management Systems: Install any optional heat management systems if required.
• C. Securing and Leveling the Appliance: Secure the appliance in place and ensure it is level.
• D. Installing the Non-combustible Board: Install non-combustible board as specified.

FAQs

• Q: What should I do if I encounter a gas leak?
  • A: In case of a gas leak, do not try to light any appliance, leave the building immediately, and call your gas supplier or the fire department from a safe location.

“`

Installation Manual
Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation. OWNER: Retain this manual for future reference.

NOTICE: DO NOT discard this manual!
Models:
6000C-IFT 6000C-IFTLP 8000C-IFT 8000C-IFTLP

WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage.
· DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
· What to do if you smell gas
– DO NOT try to light any appliance.
– DO NOT touch any electrical switch. DO NOT use any phone in your building.
– Leave the building immediately.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
– If you cannot reach your gas supplier, call the fire department.
· Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 in the United States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter. See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

DANGER HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and must be installed for the protection of children and other at-risk individuals.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

1

Safety Alert Key:
· DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. · WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. · CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. · NOTICE: Used to address practices not related to personal injury.
Note: The term “recommend” or “recommended” does not indicate a requirement. It is a best practice suggested by Hearth & Home Technologies®. Failure to perform the recommended task will not result in a safety concern.

= Contains updated information.

2

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Installation Standard Work Checklist

ATTENTION INSTALLER:
Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

Customer:

Date Installed:

Lot/Address:

Location of Fireplace:

Installer:

Model (circle one): 6000C-IFT

6000C-IFTLP

Dealer/Distributor Phone #

8000C-IFT

8000C-IFTLP

Serial #:

WARNING! Risk of Fire or Explosion! Failure to install appliance according to these instructions could lead to a re or explosion.

Appliance Install Veried that the chase is insulated and sealed. (Pg. 17) Required non-combustible board is installed. (Pg. 42) Veried clearances to combustibles. (Pg. 15-16) Fireplace is leveled and secured. (Pg. 42)

YES

IF NO, WHY?

Venting/Chimney Section 7 (Pg 43-48) Venting conguration complies to vent diagrams. Venting installed, locked and secured in place with proper clearance. Elbow heat shield installed per requirements. (Pg 24, 36) Firestops installed. Attic insulation shield installed. Exterior wall/Roof ashing installed and sealed. Terminations installed and sealed.

Electrical Section 8 (Pg 49-51) Unswitched power (110-120 VAC) provided to the appliance. Switch wires properly installed.

Gas Section 9 (Pg 52-53) Proper appliance for fuel type. Was a conversion performed? Leak check performed and inlet pressure veried. Veried proper air shutter setting for installation type.
Finishing Section 10 (Pg 54-58) Combustible materials not installed in non- combustible areas. Veried all clearances meet installation manual requirements. Mantels and wall projections comply with installation manual requirements.

Appliance Setup Section 11 (Pg 59-65) All packaging and protective materials removed (inside & outside of appliance). Refractories, logs and embers installed correctly. Glass assembly installed and secured. Accessories installed properly. Decorative front properly installed. Manual bag and all of its contents are removed from inside/under
the appliance and given to party responsible for use and operation. Started appliance and veried no gas leaks exist.

Hearth & Home Technologies recommends the following: · Photographing the installation and copying this checklist for your le. · That this checklist remain visible at all times on the appliance until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed

Comments Communicated to party responsible ____ by __on ___

= Contains updated information.

(Builder / Gen. Contractor/) (Installer)

(Date)
2502-982 11/17

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

3

Product Specifications and Important Safety Information

A. Appliance Certification
MODELS: 6000C-IFT, 6000C-IFTLP, 8000C-IFT, 8000C-IFTLP
LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Heater STANDARD: CSA / ANSI Z21.88:19 · CSA 2.33:19
This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.
NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE. This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

C. BTU Specifications

Models
(U.S. or Canada)

6000C-IFT (NG)
6000C-IFTLP (Propane)
8000C-IFT (NG)
8000C-IFTLP (Propane)

(0-2000 FT) (0-2000 FT) (0-2000 FT) (0-2000 FT)

Maximum Minimum Orifice

Input

Input

Size

BTU/h

BTU/h (DMS)

30,000

16,000

37

29,000

17,000

52

35,000

19,000

33

34,000

17,000

50

D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.
When installing above 2000 feet elevation:
· In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.
· In CANADA: Input ratings are certified without a reduction of input rate for elevations up to 4500 feet (1370 m) above sea level. Please consult provincial and/ or local authorities having jurisdiction for installations at elevations above 4500 feet (1370 m).
Check with your local gas utility to determine proper orifice size.

B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certification Council SGCC# 1595 and 1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to 15 U.S. Code (USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”
Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

4

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC shall be considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.
· A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.
H. California
WARNING: This product and the fuels used to operate this product (liquid propane or natural gas), and the products of combustion of such fuels, can expose you to chemicals including benzene, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www. P65Warnings.ca.gov.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

5

Note: The following requirements reference various Massachusetts and national codes not contained in this document.
I. Requirements for the Commonwealth of Massachusetts
For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) in. in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2) (a)1 through 4:
· The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and
· Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
· Detailed instructions for the installation of the venting system design or the venting system components; and
· A complete parts list for the venting system design or venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:
· The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
· The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.

6

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

2 Getting Started
A. Design and Installation Considerations
Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits. Before installing, determine the following: · Where the appliance is to be installed. · The vent system configuration to be used. · Gas supply piping requirements. · Provisions for optional heat management system. · Electrical wiring requirements. · Framing and finishing details. · Whether optional accessories–devices such as a fan,
wall switch, or remote control–are desired.
Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies recommends HHT Factory Trained or NFI certified professionals.
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

B. Good Faith Wall Surface

FIREPLACE OPENING

TO CEILING 127°F

123°F

132°F

30 in.

135°F

24 in.

18 in. 147°F
12 in. 6 in.

MEASUREMENTS FROM TOP EDGE OF THE OPENING

APPLIANCE FRONT

Figure 2.1 Good Faith Wall Surface Temperatures Above Appliance

If installing a television (TV) above the appliance, see Section 3 of the appliance Owner’s Manual.
NOTICE: Temperatures listed above are taken with a temperature measuring probe as prescribed by the test standard used for appliance certification. Temperatures on walls or mantels taken with an infrared thermometer may yield increased temperatures of up to 30 degrees or more depending on the thermometer settings and material characteristics being measured. Use appropriate finishing materials that are able to withstand these conditions. For additional finishing guidelines, see Section 10.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

Hammer

Phillips screwdriver Manometer

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Flat blade screwdriver

Non-corrosive leak check solution

1/2 – 3/4 in. length, #6 or #8 Self-drilling screws

Caulking material (300 ºF minimum continuous exposure rating)

One 1/4 in. female connection (for optional fan).

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

7

D. Inspect Appliance and Components
· Carefully remove the appliance and components from the packaging.
· The vent system components and decorative doors and fronts may be shipped in separate packages.
· If packaged separately, the log set and appliance grate must be installed.
· Report to your dealer any parts damaged in shipment, particularly the condition of the glass.
· Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.
WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:
· Installation and use of any damaged appliance or vent system component.
· Modification of the appliance or vent system. · Installation other than as instructed by Hearth & Home
Technologies. · Improper positioning of the gas logs or the glass assembly. · Installation and/or use of any component part not approved
by Hearth & Home Technologies. Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

8

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

3 Framing and Clearances
A. Appliance/Decorative Front Dimension Diagrams
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

N
HEAT MANAGEMENT SYSTEMS ACCESS (LEFT & RIGHT SIDES)
S

GAS LINE

T

ACCESS

O
P LEFT SIDE

R Q

L M
TOP VIEW
B A FRONT VIEW

J K

ELECTRICAL ACCESS

CD E

N
(CL)
I G

F

H

RIGHT SIDE

Appliance Dimensions Table

Location Inches Millimeters

A

41

1041

B

36-1/8

918

C

33-1/2

851

D

34-5/8

879

E

2-1/4

57

F

9-11/16

246

G

26-7/8

683

H

6 dia.

152

I

39-7/8

1013

J

21

533

Location K L M N O P Q R S T

Inches 11-11/16 28-1/2 14-1/4
8-1/2 2-7/8 8-1/2
1 40-7/8 14-3/16 15-3/8

Millimeters 297 724 362 216 73 216 25 1038 360 391

Figure 3.1 Appliance Dimensions – 6000C-IFT Models

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

9

L M

N
HEAT MANAGEMENT SYSTEMS ACCESS (LEFT & RIGHT SIDES)
S

GAS LINE ACCESS

T R

O

Q

P LEFT SIDE

TOP VIEW
B A FRONT VIEW

J K

ELECTRICAL ACCESS

CD E

N
(CL) I
G

F H
RIGHT VIEW

Appliance Dimensions Table

Location A B C D E F G H I J

Inches 48
43-1/8 35-1/2 36-5/8 2-3/8 9-15/16 28-7/8
6 41-7/8
21

Millimeters 1219 1096 902 930 60 252 734 152 1064 533

Location K L M N O P Q R S T

Inches 11-11/16 35-1/2 17-3/4
8-1/2 2-7/8 8-1/2
1 42-7/8 14-1/16 17-1/16

Millimeters 297 901 451 216 73 216 25 1089 357 433

Figure 3.2 Appliance Dimensions – 8000C-IFT Models

10

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

FOLIO DECORATIVE FRONTS

B A

FG

E

C

D

6000 FOL-36 8000 FOL-42

A

B

C

in. 32-7/16 23-1/8 35-13/16

mm

824

587

910

in. 39-7/16 25-5/16 42-13/16

mm 1002

643

1087

D 1-1/2
38 1-1/2
38

E 8-1/4 210 8-1/4 210

ARCADIA DECORATIVE FRONTS

F 32-1/8
816 34-1/8
867

G 33-9/16
853 35-11/16
907

B A

F

G

E

C

D

6000 ARC-36 8000 ARC-42

A

B

in. 32-7/16 20-1/2

mm

824

521

in. 39-7/16 22-7/16

mm 1002

570

Figure 3.3 Decorative Front Dimensions – Folio and Arcadia

C 37-1/4
946 44-1/4 1124

D 1-1/4
32 1-1/4
32

E 7-11/16
195 7-11/16
195

F 32-7/8
835 34-13/16
884

G 34-1/8
867 36-1/16
916

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

11

HALSTON DECORATIVE FRONTS

A B

FG

E
D C

6000 HAL-36 8000 HAL-42

A

in. 32-7/16

mm

824

in. 39-7/16

mm 1002

B 21-1/4
540 23-1/8
587

C 37-1/4
946 44-1/4 1124

D 1-1/4
32 1-1/4
32

E 7-1/4 184 7-1/4 184

F 32-7/8
835 34-13/16
884

G 34-1/8
867 36-1/16
916

Figure 3.4 Decorative Front Dimensions – Halston

12

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

CHATEAU FORGE DECORATIVE FRONTS

B A

G F

C

A

in. 32-1/4

6000 CHAF-36

mm

819

in. 39-1/4

8000 CHAF-42

mm

997

B 20-3/4
527 22-5/8
575

C 37 940 44 1118

GALLERIA DECORATIVE FRONTS

D 1-3/16
30 1-1/4
32

E

D
E 7-9/16
192 7-5/8 194

F 32-7/8
835 34-3/4
883

G 34-1/8
867 36 914

B A

F G

E

C

D

6000 GALLERIA-6 8000 GALLERIA-8

A

in. 31-9/16

mm

802

in. 38-9/16

mm

979

B 20-7/8
530 22-3/4
578

C 37-1/8
943 44-1/16
1121

Figure 3.5 Decorative Front Dimensions – Chateau Forge and Galleria

D 1-1/4
32 1-1/4
32

E 7-1/2 191 7-1/2 191

F 32-7/8
835 34-3/4
883

G 34-1/16
865 36 914

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

13

CLEAN FACE DECORATIVE FRONTS

A B

F

G

E

D

C

6000 CF-36 8000 CF-42

A

B

C

in. 31-9/16 22-1/8 35-13/16

mm

802

562

910

in. 38-1/2 24-1/16 42-3/4

mm

978

611

1086

IRON AGE DECORATIVE FRONTS

D 3-1/2
89 3-1/2
89

E 4-9/16
116 4-9/16
116

F 26-13/16
681 28-11/16
729

G 28-15/16
735 30-13/16
783

A

F

G

B

E

C

A

B

C

6000 FSI-36

in. 27-3/8

mm

695

23-1/8 587

37-3/16 945

in. 34-3/8 25-3/16 44-3/16

8000 FSI-42

mm

873

640

1122

Figure 3.6 Decorative Front Dimensions – Clean Face and Iron Age

D 1-1/4
32 1-1/4
32

D
E 6-3/4 172 6-3/4 172

F 32-7/8
835 34-13/16
884

14

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

G 34-1/8
867 36-1/16
916

B. Clearances to Combustibles
When selecting a location for the appliance it is important to consider the required clearances to walls. See Figure 3.7.
WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

NOTE: THE REAR STANDOFF MAY NEED TO BE REMOVED WHEN VENTING AT 45º
A G
1/2 IN.

A D

B C
TOP VENT ONE 90º ELBOW

B
ALCOVE

INSTALLATION

Refer to Section 10.B for mantel and wall projection information.
Consider the mantel or cabinet system to be installed and comply with the necessary requirements for elevated hearth. Refer to instructions included with cabinet system.

REAR VENT,

REAR VENT

HORIZONTAL TERMINATION TWO ELBOWS

REAR VENT

ONE ELBOW

B

NO ELBOWS

B

B

D

F

D H
D

A

B

C

D

E

F

G

H

6000 in.

51

mm 1295

42 1067

72

56-5/8 See Section 10.B

22

1829

1438 Mantel Projections 559

17-3/4 451

8 203

8000 in. 55-7/8
mm 1419

49 1245

79

61-1/2 See Section 10.B

22

2007

1562 Mantel Projections 559

19-3/4 502

10 254

Figure 3.7 Appliance Locations

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

15

COMBUSTIBLE FLOORING MAY BE INSTALLED NEXT TO THE FRONT OF THE APPLIANCE.
A E

B
C D

F H

G

I

J

Models
in. 6000
mm in. 8000 mm

A

B

Rough Rough Opening Opening (Width) (Height)

10 40-1/8

254 1019

10 42-1/8

254 1070

• MINIMUM FRAMING DIMENSIONS

C**

D

E

F

G***

H

I

J

Rough Opening (Depth)

Rough Opening (Width)

Clearance to Ceiling (Measured from top of
appliance opening)

Combustible Combustible Behind Sides of Front of

Floor

Flooring Appliance Appliance Appliance

22

42

32

0

0

1/2

1/2

36

559

1067

813

0

0

13

13

914

22

49

32

0

0

1/2

1/2

36

559

1245

813

0

0

13

13

914

• Adjust framing dimensions for interior sheathing (such as sheetrock) C** Add 12 inches for rear venting with one 90º elbow. G*** For installations with vinyl flooring, see Section 3.D.

Figure 3.8 Clearances to Combustibles

16

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

C. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.
NOTICE: Where required by code, install only sprinkler heads with a sprinkler activation temperature classified as Extra High.
· Sprinklers inside of chase: Keep sprinkler head away from vent and chimney.
· Heat Management applications: Maintain 36 inches of clearance to openings from which heat is discharged such as heat zone registers, etc. Refer to Section 6.B for Heat Management options allowed for this appliance.
Chases should be constructed and insulated in the same manner as the thermal envelope of the home based on the code requirements for that climate zone to prevent air leakage and draft problems. The chase is an extension of the building thermal envelope.
To further prevent drafts and air leakage, the wall shield and ceiling firestops should be caulked with caulk with a minimum of 300 ºF continuous exposure rating to seal gaps. Gas line holes and other openings should be caulked with caulk with a minimum of 300 ºF continuous exposure rating or stuffed with unfaced insulation. If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting cold up into the room.
NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.
WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:
· Insulation and other materials must be secured to prevent accidental contact.
· The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.
· Failure to maintain airspace may cause overheating and a fire.

D. Floor Protection
Vinyl Flooring
Vinyl flooring is sensitive to heat. Hearth and Home Technologies does not recommend adhesive based vinyl flooring due to thermal expansion. Floating- style flooring can be used, but will reach temperatures up to 110 °F in a room with ambient temperature of 70 °F. Consult flooring specifications to ensure compatibility.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

17

Termination Location and Vent Information

A. Vent Termination Minimum Clearances
WARNING
Fire Risk. Maintain vent clearance to combustibles as specified. · DO NOT pack air space with insulation or other
materials. Failure to keep insulation or other materials away from vent pipe could cause overheating and fire.

A 6 in. (minimum) up to 20 in.
152 mm/508 mm
20 in. and over

B 18 in. minimum
457 mm
0 in. minimum

Gas, Wood or Fuel Oil Termination Cap

B A *

2 FT. MIN.
GAS DIRECT VENT TERMINATION CAP

20 INCHES MIN.
LOWEST DISCHARGE
OPENING

HORIZONTAL OVERHANG
VERTICAL WALL

X 12
ROOF PITCH IS X/ 12
H (MIN.) – MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12…………………………………………………..1.0*

Over 6/12 to 7/12………………………………………….1.25*

Over 7/12 to 8/12………………………………………….1.5*

Over 8/12 to 9/12………………………………………….2.0*

Over 9/12 to 10/12………………………………………..2.5*

Over 10/12 to 11/12 ………………………………………3.25

Over 11/12 to 12/12 ………………………………………4.0

Over 12/12 to 14/12………………………………………5.0

Over 14/12 to 16/12………………………………………6.0

Over 16/12 to 18/12………………………………………7.0

Over 18/12 to 20/12………………………………………7.5

Over 20/12 to 21/12………………………………………8.0

• H minimum may vary depending on regional snowfall. Refer to local codes.

Figure 4.1 Minimum Height From Roof to Lowest Discharge Opening

Gas Termination
Cap **

• If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.
  ** In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 4.2 Staggered Termination Caps
CAUTION! Risk of Burns! Termination caps are HOT, consider proximity to doors, traffic areas or where people may pass or gather (sidewalk, deck, patio, etc.). Listed cap shields available. Contact your dealer.
· Local codes or regulations may require different clearances.
· Hearth & Home Technologies assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.
· Vinyl protection kits are suggested for use with vinyl siding. · Measure horizontal and vertical termination cap clearances
as noted in Figure 4.3.

H=Measure Horizontal Distances from H

H

V=Measure Vertical Distances from V

H

V

V

C=L6EAINR. ANCE

Figure 4.3

18

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

B. Vent Terminal Clearances

= AREA WHERE TERMINAL IS NOT PERMITTED

C
V JB V

B DV

X = AIR SUPPLY INLET
F
V = VENT TERMINAL

V

B

V A

H or i

XV

E

G

H

M V

VHV

V

A

U.S.A. Installations: In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code. Canadian Installations: In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code.

V L
V K Electrical K V
Service
C V

U.S.A.

CANADA

A Clearance above grade,veranda, porch, deck, or balcony

12 in. (305 mm) 12 in. (305 mm)

B

Clearance to window or door that may be opened, or to permanently closed window U.S.A.: = 9 in. min. (229 mm min.) CANADA: = 12 in. min. ( 305 mm min.)

clearance below unventilated soffit C clearance below ventilated soffit
clearance below any vinyl soffits and electrical service D clearance to outside corner E clearance to inside corner

18 in. (457 mm) 18 in. (457 mm) 30 in. (762 mm) 6 in. (152 mm) 6 in. (152 mm)

18 in. (457 mm) 18 in. (457 mm) 30 in. (762 mm) 6 in. (152 mm) 6 in. (152 mm)

F

not to be installed above a gas meter/regulator assembly within 3 feet horizontally from the center-line of the regulator

3 ft (914 mm)

3 ft (914 mm)

G clearance to gas service regulator vent outlet

3 ft (914 mm)

3 ft (914 mm)

H

clearance to non-mechanical air supply inlet to building or the combustion air inlet to

9 in. min.

any other appliance termination (mechanical or non-mechanical)

(229 mm min.)

12 in. min. (305 mm min.)

clearance to a mechanical (powered) air supply inlet

I

(All mechanical air intakes within 10 feet of a horizontal termination cap must be 3 ft (914 mm)

a minimum of 3 feet below termination.)

6 ft (1.8 m)

On public property: clearance above paved sidewalk or a paved driveway.

7 ft (2.1 m)

7 ft (2.1 m)**

J **(A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.)

clearance from sides of electrical service

6 in. (152 mm) 6 in. (152 mm)

K

Location of the vent termination must not interfere with access to the electrical service.

clearance above electrical service

12 in. (305 mm)

L

Location of the vent termination must not interfere with access to the electrical service.

clearance under veranda, porch, deck, balcony or overhang *(Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of M two sides beneath the floor.)

18 in. (457 mm)

vinyl or composite overhang

42 in. (1067 mm)

Figure 4.4 Minimum Clearances for Termination

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

12 in. (305 mm)
12 in. (305 mm)* 42 in. (1067 mm)
19

C. Approved Pipe
This appliance is approved for use with Hearth & Home Technologies DVP or SLP venting systems. Refer to Section 12.A for vent component information and dimensions. Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting systems.
DO NOT mix pipe, fittings or joining methods from different manufacturers.
The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance.

20

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

D. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect. See Figure 4.4.
Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows. See Figure 4.5.
Figure 4.6 shows the vertical and horizontal offsets for DVP or SLP elbows.

RISE

VERTICAL

EFLFEENCGTITVHE RUN

Y

X

Vent Type DVP SLP

Inches 6-5/8 5-1/4

X Millimeters
168 133

Inches 16-1/2 11-3/8

Y Millimeters
419 289

X

HORIZONTAL

SLP Pipe
SLP4 SLP6 SLP12 SLP24 SLP36 SLP48 SLP6A SLP12A

Effective Length

Inches Millimeters

4

102

6

152

12

305

24

610

36

914

48

1219

3 to 6 76 to 152

3 to 12 76 to 305

Rise/Run

Inches Millimeters

2-3/4

70

4-1/4

108

8-1/2

216

17

432

25-1/2

648

34

864

2-1/8-4-1/4 54-108

2-1/8-8-1/2 54-216

DVP Pipe
DVP4 DVP6 DVP12 DVP24 DVP36 DVP48 DVP6A DVP12A

Effective Length Inches Millimeters

4

102

6

152

12

305

24

610

36

914

48

1219

3 to 6 76 to 152

3 to 12 76 to 305

Rise/Run

Inches

Millimeters

2-3/4

70

4-1/4

108

8-1/2

216

17

432

25-1/2

648

34

864

2-1/8-4-1/4 54-108

2-1/8-8-1/2 54-216

X

Vent Type
DVP SLP

Inches 16-1/4 11-1/4

X Millimeters 413 286

Figure 4.6 Vertical and Horizontal Offset for DVP and SLP Elbows

Figure 4.5

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

21

E. Measuring Standards
Vertical and horizontal measurements listed in the vent diagrams were made using the following standards: · Pipe measurements are shown using the effective length
of pipe. See Section 12.A (Figure 12.1 for DVP, Figure 12.9 for SLP) for information on effective length of pipe components. · Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 4.7). · Vertical terminations are measured to top of last section of pipe. See Figure 4.8. · Horizontal pipe installed level with no rise.
MEASURE TO SHADED SURFACE (OUTSIDE MOUNTING SURFACE)
Figure 4.7 Measure to Outside Mounting Surface

Figure 4.8 Measure to Top of Last Section of Pipe

22

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

F. Vent Diagrams
General Rules:
· SUBTRACT 3 ft. from the total H measurement for each 90º elbow installed horizontally.
· SUBTRACT 1-1/2 ft. from the total H measurement for each 45º elbow installed horizontally.
· A maximum of three 90º elbows (or six 45º elbows) may be used in any vent configuration. Some elbows may be installed horizontally. For example, see Figure 4.11.
· Elbows may be placed back to back anywhere in the system.
· Any 90º elbow may be replaced with two back to back
45º elbows.
· When penetrating a combustible wall, a wall shield firestop must be installed.
· When penetrating a combustible ceiling, a ceiling firestop must be installed.
· Horizontal runs of vent do not require vertical rise; horizontal runs may be level.
· Horizontal termination cap should have a 1/4 inch downward slant to allow any moisture in cap to be released. See Figure 4.9.

WARNING
Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling firestops. · ALWAYS maintain specified clearances around
venting and firestop systems. · Install wall shield and ceiling firestops as speci-
fied. Failure to keep insulation or other material away from vent pipe may cause fire.
WARNING
Fire Risk. · When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces, a 6 inch minimum vertical vent section is required before installing first elbow.
Note: The 6000/8000 series fireplaces can adapt to SLP series vent pipe, if desired.
When venting off the top of the unit, use a DVP-2SL adapter and a minimum 48 inch vertical section of SLP series vent pipe. A DVP-SLP24 adapter may also be used with a 24 inch vertical section of SLP series vent pipe. After the 48 inch vertical section, the venting table rules must be followed. The first 48 inch vertical section is NOT counted as part of the vertical components in the table. It is still counted as part of the overall maximum run. All venting table rules for the vent run must still be followed.
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal

1/4 in. max. (6 mm)
Figure 4.9

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

23

Top Vent – Horizontal Termination One Elbow

Note: For corner installations: A 6 inch (152 mm) section of straight pipe may need to
be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top
standoffs.

WARNING! Risk of Fire! Elbow heat shield required
when V1 = 2 ft. or less. Clearances to combustibles must be maintained. See Section 5.A.

6000C-IFT

V1 Minimum Elbow only

H1 Maximum

2 ft

610 mm

6 in. 152 mm

4 ft.

1.2 m

1 ft.

305 mm

6 ft.

1.8 m

1-1/2 ft. 457 mm 10 ft.

3.0 m

2 ft.

610 m

15 ft.

4.6 m

2-1/2 ft. 762 mm 20 ft.

6.1 m

3 ft.

914 mm

25 ft.

7.6 m

V1 + H1 = 40 ft. (12.2 m) Maximum H1 = 25 ft. (7.6 m) Maximum

8000C-IFT

V1 Minimum

H1 Maximum

Elbow Only

2 ft.

610 mm

1 ft.

305 mm

3 ft.

914 mm

2 ft.

610 mm

6 ft.

1.8 m

3 ft.

914 mm

11 ft.

3.4 m

4 ft.

1.2 m

20 ft.

6.1 m

V1 + H1 = 40 ft. (12.2 m) Maximum H1 = 20 ft. (6.1 m) Maximum

ELBOW HEAT SHIELD (Required when V1 = 2 ft. or less)
V1 H1

Figure 4.10 24

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Top Vent – Horizontal Termination – (continued)

Two Elbows
Note: For corner installations: A 6 in. (152 mm) section of straight pipe may need to be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top standoffs.

6000C-IFT

V1 Minimum

H1 + H2 Maximum

Elbow only

Not allowed

6 in. 152 mm 2 ft. 610 mm

1 ft. 305 mm 4 ft.

1.2 m

1-1/2 ft. 457 mm 11 ft.

3.4 m

2 ft. 610 mm 19 ft.

3.8 m

2-1/2 ft. 762 mm 22 ft.

6.7 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 22 ft. (6.7 m) Maximum V1 = 1 ft. (305 mm) Minimum

8000C-IFT

V1 Minimum

H1 + H2 Maximum

Elbow only

Not allowed

6 in. 152 mm

Not allowed

1 ft. 305 mm 2 ft. 610 mm

2 ft. 610 mm 4 ft.

1.2 m

3 ft. 914 mm 6 ft.

1.8 m

4 ft. 1.2 m

8 ft.

2.4 m

6 ft.

1.8 m

12 ft.

3.6 m

10 ft.

3.0

20 ft.

6.1 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 20 ft. (6.0 m) Maximum V1 = 1 ft. (305 mm) Minimum

H2

V1

H1

INSTALLED HORIZONTALLY

Figure 4.11

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

25

Top Vent – Horizontal Termination – (continued)

Three Elbows

V1 Min. Elbow only 6 in. 152 mm 1 ft. 305 mm

H1 Max. 2 ft. 610 mm 3 ft 914 mm 6 ft. 1.8 m

V2 Min.

0 in.

0 mm

6 in.

152 mm

1 ft.

305 mm

H2 Max.

1 ft.

305 mm

2 ft.

610 mm

6 ft.

1.8 m

2 ft. 610 mm 11 ft. 3.4 m

2 ft.

610 mm 10 ft.*

3.1 m*

3 ft. 914 mm 16 ft 4.9 m

3 ft.

914 mm 14 ft.*

4.3 m*

*H1 + H2 = 20 ft. (6.1 m) Maximum

V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum

H2

V2

H1

V1

Figure 4.12 26

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Top Vent – Vertical Termination
No Elbow
V1 = 40 ft. Max. (12.4 m) V1 = 3 ft. Min. (914 mm)
Note: If installing a vertical vent/ termination off the top of the appliance, the flue restrictor should be used.

Flue Restrictor Instructions
1. Remove exhaust shield using a 1/4 inch nut driver by removing the three screws securing it in place. See Figure 4.14.
2. Orientate and align the two pieces of the flue restrictor as shown in Figure 4.16.
EXHAUST SHIELD
FLUE RESTRICTOR INSTALLED

Figure 4.13

Figure 4.14

V1

3. Match the amount of vertical you have in the system

with the chart to find the appropriate position to set the

flue restrictor. See Figure 4.15 and 4.16.

4. Center the two flue restrictor pieces on the vent at the

setting selected in step 3 and secure in place by using

two self-tapping screws. See Figure 4.14.

5. Reinstall the exhaust shield.

Vertical 4 ft. 8 ft. 15 ft. 20 ft. 25 ft. 30 ft. 35 ft. 40 ft.

TOP VENT

NG

Propane

1-1

No Restrictor

2-2

1-2

REAR VENT

NG

Propane

No

No

Restrictor Restrictor

1-1

No Restrictor

3-3

3-2

2-2

1-2

3-4

3-3

3-3

2-3

3-4

3-3

3-3

2-3

4-4

3-4

3-4

3-3

4-4

3-4

3-4

3-3

4-4

4-4

4-4

3-4

Figure 4.15

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

27

Top Vent – Vertical Termination (continued)
ALWAYS USED WITH THE HOLES TO THE RIGHT
4 5 1 2 3 45

5 4321
ALWAYS USED WITH THE HOLES TO THE LEFT Note: If the DVP-2SL or DVP-SLP24 adapter is used with SLP pipe, you MUST subtract one number from the table in Figure 4.14. Example: Top vent 40 ft vertical with DVP pipe = 4-4 Top vent 40 ft vertical with SLP pipe = 3-3
Figure 4.16 Setting the Flue Restrictor
Two Elbows
V2

5 4321
FLUE RESTRICTOR SET TO 4-4

V1 Elbow only

H1 Maximum V2 V1 + V2 Min.

2 ft. 610 mm

6 in. 152 mm 6 ft. 1.8 m

2 ft. 610 mm 11 ft. 3.4 m

3 ft. 914 mm 16 ft. 4.9 m

4 ft.

1.2 m 20 ft. 6.1 m

V1 + V2 + H1 = 50 ft. (15.2 m) Maximum *No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)

V1 H1

Figure 4.17 28

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Top Vent – Vertical Termination – (continued)

Three Elbows

V1 Elbow only

H1 + H2

V2

1 ft. 305 mm *

V1 + V2 Minimum

H1 + H2 Maximum

1 ft.

305 mm

6 in. 152 mm 2 ft. 610 mm *

2 ft.

610 mm

1 ft. 305 mm 2 ft. 610 mm *

2 ft.

610 mm

2 ft. 610 mm 4 ft.

1.2 m

4 ft.

1.2 m

3 ft. 914 mm 9 ft.

2.7 m

9 ft.

2.7 m

4 ft.

1.2 m 18 ft. 5.5 m *

18 ft.

5.5 m

H1 + H2 = 20 ft. (6.1 m) Maximum

V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum

• No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m).

V2

H1

H2

V1

INSTALLED HORIZONTALLY

Figure 4.18

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

29

Rear Vent – Horizontal Termination No Elbow

H1 = 16 in. (406 mm) Maximum

H1
Figure 4.19
One 45º Elbow
Do not use a 45º elbow in corner installations. Use two 90º elbows instead.

90-DEGREE ELBOWS

Figure 4.20 30

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Rear Vent – Horizontal Termination – (continued)

Two Elbows

H1 Maximum

V1 Minimum

H2 Maximum H1 + H2 Maximum

1 ft. 305 mm

Back to Back 90º Elbows

1 ft. 305 mm 2 ft. 610 mm

2 ft. 610 mm 6 in. 152 mm 2 ft. 610 mm 4 ft. 1.2 m

3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m

3 ft. 914 mm 2 ft. 610 mm 4 ft.

1.2 m

7 ft.

2.1 m

3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m

3 ft. 914 mm 4 ft 1.2 m 17 ft. 5.2 m 20 ft. 6.1 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 = 3 ft. (914 mm) Maximum *H1 + H2 = 20 ft (6.1 m) Maximum

H2

V1

Figure 4.21
Three Elbows
INSTALLED HORIZONTALLY
H3

H1

H1 Maximum 1 ft. 305 mm

V1 Minimum
Back to Back 90º Elbows

H2+ H3

H1+ H2+ H3 Max.

1 ft. 305 mm 2 ft. 610 mm

2 ft. 610 mm 6 in. 152 mm 1.5 ft. 457 mm 3.5 ft. 1.1 m

3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m

3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m

3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m

3 ft. 914 mm 4 ft. 1.2 m 12 ft. 3.7 m 15 ft. 4.6 m

V1+ H1+ H2+ H3= 40 ft. (12.2 m) Maximum H1= 3 ft. (914 mm) Maximum H1+ H2+ H3= 20 ft. (6.1 m) Maximum

H2

V1

H1

Figure 4.22

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

31

Rear Vent – Vertical Termination One Elbow
V1 H1
Figure 4.23
Two Elbows
V1

V1 Minimum

H1 Maximum

6 in. 152 mm 2 ft. 610 mm

1 ft. 305 mm 3 ft. 914 mm

2 ft. 610 mm 5 ft. 1.5 m

3 ft. 914 mm 7 ft. 2.1 m

4 ft.

1.2 m 8 ft. 2.4 m

5 ft.

1.5 m 8 ft. 2.4 m

V1 + H1 = 40 ft. (12.2 m) Maximum H1 = 8 ft. (2.4 m) Maximum

V1 Minimum

H1 + H2 Maximum

Back to Back 90º Elbows

3 ft.

914 mm

2 ft.

610 mm

6 ft.

1.8 m

4 ft.

1.2 m

9 ft.

2.7 m

6 ft.

1.8 m

12 ft.

3.7 m

8 ft.

2.4 m

15 ft.

4.6 m

V1 + H1+ H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 15 ft. (4.6 m) Maximum

Figure 4.24 32

INSTALLED

HORIZONTALLY

H1

H2

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Rear Vent – Vertical Termination – (continued)

Three Elbows
V2

H1 Maximum

V1 Minimum

H2

H1 + H2 Maximum

2 ft. 610 mm 6 in. 152 mm 2 ft.

610 mm

4 ft.

1.2 m

3 ft. 914 mm 1 ft. 305 mm 4 ft. 1.2 m 7 ft.

2.1 m

5 ft. 1.5 m 2 ft. 610 mm 6 ft. 1.8 m 11 ft. 3.4 m

7 ft.

2.1 m 3 ft. 914 mm 8 ft. 2.4 m 15 ft.

4.6 m

8 ft

2.4 m

4 ft.

1.2 m 10 ft. 3.1 m 18 ft. 5.5 m

H1= 8 ft (2.4 m) Maximum V1 + V2 + H1 + H2= 40 ft (12.2 m) Maximum H1 + H2 = 18 ft (5.5 m) Maximum

H2 V1

Figure 4.25
Three Elbows

V1 H3

H1

H1 H2 H3

V1 Minimum H1 + H2 + H3 Maximum

• • • 8 ft. 2.4 m 6 ft.

1.8 m

• • • 9 ft. 2.7 m 7 ft.

2.1 m

• • • 10 ft. 3.1 m 8 ft.

2.4 m

• • • 10 ft. 3.1 m 8 ft.

2.4 m

V1 + H1 + H2 + H3 = 40 ft. (12.2 m) Maximum *No specific restrictions on this value EXCEPT V1 + H1 + H2 + H3 cannot exceed 40 ft. (12.2 m) Maximum
H1 + H2 + H3 = 8 ft. (2.4 m) Maximum

H1

H2

Figure 4.26

INSTALLED HORIZONTALLY

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

33

Coaxial to Colinear Venting

The coaxial to colinear adapter (DV-46DVA-GCL) is approved for installations into solid fuel masonry or factory
built fireplaces that have been installed in accordance with the National, Provincial, State and local building codes. Reference Table 1 for required parts. The DV-46DVAGCL must be recessed into existing masonry fireplace. See Table 2 and Figure 4.28.

Table 1

REQUIRED PARTS

DV-46DVA-GCL Coaxial/Colinear Appliance Connector

LINK-DV30B Flex Liner Kit

768-380A

Stainless Steel Flex Pipe

DVP-2SL

Adapter (Appliances using DVP pipe)

INLET AIR VENT PIPE

EXHAUST VENT PIPE

Figure 4.27. Coaxial/Colinear Appliance Connector
WARNING! Risk of Fire! Coaxial to colinear venting configuration may only be used in existing non-combustible chimney. Installation in any other venting application could cause fire.
Prior to installing the gas appliance:
· Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.
· Replace component parts of the chimney and fireplace as specified by the professionals.
· Ensure all joints are properly engaged and the chimney is properly secured.

Table 2

CLEARANCE TO COMBUSTIBLES REQUIREMENTS

DV-46DVA-GCL

3 IN.

Exhaust Vent Pipe

5 IN.

OUTSIDE FACE OF FIREPLACE
EXHAUST VENT PIPE
TOP OF FIREPLACE OPENING 5 IN. MIN.
3 IN. MIN.
SHADED AREA DEFINED AS “INSIDE EXISTING MASONRY
FIREPLACE”
Figure 4.28. Existing Fireplace DV-46DVA-GCL Clearance Requirements
Clearances to Combustibles: Refer to Section 3 for clearances to the appliance, mantel, mantel legs and wall projection. Refer to Section 5 for pipe clearances to combustibles. Termination Cap For installation of termination cap see minimum vent heights for various pitched roofs. See Section 4.A. Flue Damper Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it. Venting Components The LINK-DV30B is approved for use with the coaxial/colinear venting application. The LINK- DV30B kit includes: · Two 30 foot sections of flexible vent pipe (3 inches Ø).
One section is used to draw combustion air and the other section is used to expel exhaust gases. · One vertical termination cap.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL adapter and LINK-DV30B kit. This could result in poor flame appearance, sooting, pilot malfunction, or overheating.

34

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Connecting the DV-46DVA-GCL Adapter to Appliance
Top Vent
· Remove top seal cap and insulation if equipped. See Section 6, “Appliance Preparation.” Attach the DVP2SL to the 8 inch starting collar. Follow installation instructions included with DVP-2SL kit. Attach the DV-46DVA-GCL adapter to the appliance starting collar with 3-1/2 in. self-tapping screws. See Figure 4.28.
Rear Vent
· Remove the rear seal cap and insulation if equipped. Connect the DVP-2SL adapter to the vertically positioned elbow. Follow installation instructions included with DVP2SL kit. Secure DV-46DVA-GCL adapter to DVP-2SL with 3-1/2 in. self-tapping screws. See Figure 4.29.
Connecting the LINK-DV30B to the DV-46DVA-GCL adapter
· Insert the two sections of flexible vent pipe down the existing chimney.
· Attach one section of stainless steel flex pipe to the exhaust collar on top of the DV-46DVA-GCL adapter with three screws.

· Attach one section of flexible vent pipe to the stainless steel flex pipe with three self-tapping screws.
· Attach one section of flexible vent pipe to the inlet collar on top of the DV-46DVA-GCL adapter with three selftapping screws.
· To minimize cold air drafts, seal around the flex vents at the damper inside the chimney with non-combustible unfaced fiberglass or rock wool insulation.
The DV-46DVA-GCL adapter must be recessed into existing masonry fireplace. This measurement is taken from the top of the fireplace opening. See Table 2 and Figure 4.28.
WARNING! Risk of Fire, Explosion or Asphyxiation! Do NOT connect this gas appliance to a chimney flue serving a separate solid fuel or gas burning appliance.
· Could impair safe operation of this appliance or other appliances connected to the flue.
· Vent this appliance directly outside. · Use separate vent system for this appliance.

REAR VENT
TERMINATION CAP
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL adapter and LINK-DV30B kit. This could result in poor flame appearance, sooting, pilot malfunction, or overheating.

TOP VENT
TERMINATION CAP

EXISTING CHIMNEY
EXHAUST AIR VENT PIPE
EXISTING CHIMNEY COAXIAL/COLINEAR
APPLIANCE CONNECTOR DVP-2SL
DIRECT VENT FIREPLACE

NOTICE: To achieve optimum perforV mance of appliance, minimize or avoid
bends in exhaust vent pipe.
EXISTING CHIMNEY

INLET AIR VENT PIPE
The first 3 feet of exhaust flue must be
stainless flex pipe (768-380A).
To minimize cold air drafts, seal with non-combustible insulation.

EXHAUST AIR VENT PIPE
EXISTING CHIMNEY COAXIAL/COLINEAR
APPLIANCE CONNECTOR DVP-2SL
DIRECT VENT FIREPLACE

V
INLET AIR VENT PIPE
The first 3 feet of exhaust flue must be stainless flex pipe (768-380A). To minimize cold air drafts, seal with non-combustible insulation.

HEARTH FLOOR

H

Minimum Maximum

V 10 ft. 3.05 m 40 ft. 12.2 m

H 0 ft. 0 mm 2 ft. 610 mm

Figure 4.29

FLOOR

HEARTH

Minimum Maximum

V 10 ft. 40 ft.

3.05 m 12.2 m

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

35

5 Vent Clearances and Framing
A. Pipe Clearances to Combustibles
WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles:
· Between ceiling firestops · Between wall shield firestops · Around vent system
Failure to keep insulation or other material away from vent pipe could cause overheating and fire.
WARNING! Risk of Fire! Elbow heat shield required when V1 = 2 ft. or less. Clearances to combustibles must be maintained. See Figure 4.10.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). · DVP heat shield – designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick. · If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required. · SLP heat shield – designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick). · If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.

(DVP-SLP Pipe Shown)

Elbow Heat Shield

Heat 3 in. (76 mm) Shield top clearance min.

1 in. (25 mm) clearance around vertical sections

V1

Wall

Shield

Firestop

3 in. (76 mm) top clearance *
Heat Shield
1 in. (25 mm) clearance bottom & sides

WALL

Warning! Risk of Fire: Elbow heat shield required with 3 inch top clearance or V1 of 2 ft. or less.

The attached insulation has been tested and approved by Hearth & Home Technologies and is UL approved. This insulation may contact the vent pipe.
Figure 5.2 8000C Top Insulation

Heat Shield

3 in. (76 mm) top clearance min.*
Heat Shield

Wall Shield Firestop

1 in. (25 mm) clearance bottom & sides

WALL

• When using SLP pipe, minimum clearances from the vent pipe to combustible

materials at inside wall firestops are:

Top: 2-1/2 in. (64 mm)

Bottom: 1/2 in. (13 mm)

Sides: 1 in. (25 mm)

Figure 5.1 Horizontal Venting Clearances To Combustible Materials

36

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

B. Wall Penetration Framing/Firestops
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop(s). The wall shield firestop maintains minimum clearances and prevents cold air infiltration.
· The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.
· SLP pipe – A wall shield firestop must be placed on each side of an interior wall. A minimum 1-1/2 in. (38 mm) overlap of attached heat shields must be maintained.
· DVP pipe – A wall shield firestop is required on one side only on interior walls. If your local inspector requires a wall shield firestop on both sides, then both wall shield firestops must have a heat shield (refer to Section 12.A) attached to them.
· See Section 7.G for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by non-combustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.
DO NOT PACK HOLE WITH INSULATION OR OTHER MATERIAL.

10 in.

10 in.

A*

B*

12 in.

C D

12 in.

6000 8000

A* in. 42-3/4 mm 1086 in. 45-1/8 mm 1146

B* 27-7/8
708 29-7/8
759

C 41-3/4 1060 44-1/8 1121

D 26-7/8
683 28-7/8
733

• Shows center of vent framing hole for top or rear venting. The center of the hole is one (1) in. (25 mm) above the center of the horizontal vent pipe.

Figure 5.3 Wall Penetration

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

37

C. Ceiling Firestop/Floor Penetration Framing
A ceiling firestop MUST be used between floors and attics.
· DVP pipe only – Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/floor (see Figure 5.4).
· SLP pipe only – Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 5.4).
· Frame the area with the same sized lumber as used in ceiling/floor joist.
· The ceiling firestop may be installed above or below the ceiling joists when installed with an attic insulation shield. It must be under joists between floors that are not insulated. Refer to Figure 5.5.
· Secure in place with nails or screws.
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept back from the pipe to prevent overheating.
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies requires the use of an attic shield.
The International Fuel Gas Code requires an attic shield constructed of 26 gauge minimum steel that extends at least 2 in. (51 mm) above insulation.
· Attic insulation shields must meet specified clearances to combustible materials and be secured in place.
· An attic insulation shield kit is available from Hearth & Home Technologies. Contact your dealer to order. Install attic insulation shield according to instructions included with kit.

PIPE DVP SLP
Figure 5.4 Installing Ceiling Firestop

ATTIC ABOVE A
A A 10 in. (254 mm) 9 in. (229 mm)

INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

CEILING FIRESTOP INSTALLED BELOW CEILING
Figure 5.5 Installing the Attic Shield

CEILING FIRESTOP INSTALLED ABOVE CEILING

38

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

6 Appliance Preparation
A. Vent Collar Preparation
CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.
Top Vent
Note: Instructions for rear vented models on next page.

NOTICE: Once the seal cap has been removed it CANNOT be reattached.

Figure 6.1 (Generic Fireplace Shown) Cut the seal cap strap across the rectangles next to the disk.

Figure 6.4 (Generic Fireplace Shown) Remove the in-
sulation basket and white insulation from the center vent pipe.

Figure 6.2 (Generic Fireplace Shown) Remove the white gasket material covering the seal cap.

Figure 6.5 (Generic Fireplace Shown) Remove the insulation from the outer vent pipe.

Figure 6.3 (Generic Fireplace Shown) Remove the seal cap.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

39

Figure 6.6 (Generic Fireplace Shown) To attach the first section of vent pipe, make sure to use the fiberglass gasket in the manual bag to seal between the first vent component and the outer fireplace wrap. Use 2 self tapping screws to secure the gasket to the outer wrap.
Secure the first section of venting to the fireplace by screwing through the two straps left over from cutting the seal cap strap in step 2.
Rear Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.
WARNING! Risk of Fire! DO NOT remove the installed piece of insulation from the firebox top on 8000C-IFT models. Overheating will occur.

Figure 6.9 (Generic Fireplace Shown) Fold the center parts of the retaining band out and use to remove the seal cap.
NOTICE: Once the seal cap has been removed it CANNOT be reattached.

Figure 6.7 (Generic Fireplace Shown) Fold the tabs toward the center of the seal cap (90º) and remove the insulation gasket.

Figure 6.10 (Generic Fireplace Shown) Discard the vent cap, remove and discard the insulation basket.

Figure 6.8 (Generic Fireplace Shown) Cut the metal retaining band and fold the sides out.

40

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

B. Installing Optional Heat Management Systems
NOTICE: Additional clearances are required for heat management systems installations. Provisions must be made in advance to ensure fit within the framing.
· Locate the heat management ports on the left and right sides of the appliance. Either one or two HeatZone® -Gas Kits may be installed. Remove the knockout from the fireplace and discard it. See Figure 6.12.
· Center the duct collar around the exposed hole and attach it to the fireplace with 3 screws.
Note: Do this BEFORE final positioning of fireplace.
· Determine the location for the air register/fan housing assembly.
Reference the appropriate instructions included with the kit for the remaining installation steps.

Figure 6.11 (Generic Fireplace Shown) Attach the first vent section (it will snap into place). Slide the insulation gasket onto the vent section, up against the appliance and over the tabs.

HEAT MANAGEMENT KNOCKOUT LOCATIONS (LEFT AND RIGHT SIDES)

Figure 6.12 Heat Management Knockout Locations

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

41

C. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
· Sagging or loose insulation · Insulation backing or plastic · Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.
DO NOT notch the framing around the appliance standoffs.
Failure to maintain air space clearance could cause overheating and fire.
The diagram shows how to properly square and position, and secure the appliance. See Figures 6.13 and 6.14. Nailing tabs are provided to secure the appliance to the framing members.
· Bend out nailing tabs on each side.
· Place the appliance into position.
· Keep nailing tabs flush with the framing.
· Level the appliance from side to side and front to back.
· “Square” the unit by securing diagonal dimensions to within 1/4 inch of each other. See Figure 6.13.
· Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.
· Secure the appliance to the framing by using nails or screws through the nailing tabs.
· Optional: Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

NAILING TABS (BOTH SIDES)
Figure 6.14 Proper Positioning and Securing of an Appliance
D. Installing the Non-combustible Board
The factory supplied non-combustible board spans the distance from the top of the fireplace to the center of the framing header. This board must be used. See Figure 6.15.
HEADER

A

B

Figure 6.15 Non-combustible Board

Note: Diagonal dimensions (A) and (B) must be within 1/4 inch of each other.
Figure 6.13 Positioning the Appliance Squarely

42

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

7 Venting and Chimneys
A. Assemble Vent Sections (DVP Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face toward the appliance. Attach the first pipe section to the starting collar: · Lanced pipe end of the starting collar. · Inner pipe over inner collar. · Push the pipe section until all lanced tabs snap in place. · Lightly tug on pipe to confirm it has locked.

from horizontal to vertical, one screw minimum should be put in the outer flue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe.

Required Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with 100% silicone (300 ºF minimum continuous exposure rating), including the slip section that connects directly to the horizontal termination cap.
· Apply a bead of silicone sealant (300 ºF minimum continuous exposure rating) inside the female outer pipe joint prior to joining sections. See Figure 7.1. OR
Apply a bead of silicone sealant (300 ºF minimum continuous exposure rating) to the outside of connecting joint after joining sections OR
Apply aluminum foil tape (300 ºF minimum continuous exposure rating) to the outside of connecting joint after joining sections. On horizontal pipe runs, it is recommended that the tape seam is positioned on the bottom side of the vent pipe.
· Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent could leak.
Assemble Pipe Sections
Per Figure 7.2:
· Start the inner pipe on the lanced end of section A into the flared end of section B.
· Start the outer pipe of section A over the outer pipe of section B.
· Once both vents sections are started, push firmly until all lanced tabs lock into place.
· Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe.
For 90º and 45º elbows that are changing the vent direction

Figure 7.1 High Temperature Silicone Sealant

A

Lances

B

Figure 7.2

Figure 7.3

Note: Make sure that the seams are not aligned to prevent unintentional disconnection.

CORRECT

Figure 7.4 Seams

INCORRECT

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

43

B . Assemble Vent Sections (SLP Only)
To attach the first vent component to the starting collars of the appliance: · Attach a DVP-2SL or DVP-SLP24 adapter to the starting
collar of the appliance. · Lock the vent components into place by sliding the pipe
section onto the collar. · Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 7.5. · Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration. Caulk with a minimum of 300 ºF continuous exposure rating may be used to hold the part in place. · Continue adding vent components, locking each succeeding component into place. · Ensure that each succeeding vent component is securely fitted and locked into the preceding component. It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe. Required Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications All outer pipe joints must be sealed with high temperature silicone (300 ºF minimum continuous exposure rating), including the slip section that connects directly to the horizontal termination cap. · Apply a bead of silicone sealant (300 ºF minimum continuous exposure rating) inside the female outer pipe joint prior to joining sections. See Figure 7.1. OR Apply a bead of silicone sealant (300 ºF minimum continuous exposure rating) to the outside of connecting joint after joining sections OR Apply aluminum foil tape (300 ºF minimum continuous exposure rating) to the outside of connecting joint after joining sections. On horizontal pipe runs, it is recommended that the tape seam is positioned on the bottom side of the vent pipe. · Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent could leak.
Note: Align seams to engage pipe, then rotate counterclockwise to lock
Figure 7.5 Adding Venting Components

C. Assemble Slip Sections
· Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 7.6.
· Slide together to the desired length.
Pilot hole
Figure 7.6 Slip Section Pilot Holes
· Maintain a 1-1/2 in. (38 mm) overlap between the slip section and the pipe section.
· Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 7.7.
Figure 7.7 Screws into Slip Section
· Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length. NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant (300 ºF minimum continuous exposure rating). · Apply a bead of silicone sealant (300 ºF minimum
continuous exposure rating) inside the female outer pipe joint prior to joining sections. · Only outer pipes are sealed, sealing the inner flue is not required. · All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed.

44

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

D. Secure the Vent Sections
· Vertical runs originating off the top of the appliance, with no offsets, must be supported every 8 ft. (2.44 m) after the maximum allowed 25 ft. (7.62 m) of unsupported rise.
· Vertical runs originating off the rear of the appliance, or after any elbow, must be supported every 8 ft. (2.44 m).
· Horizontal runs must be supported every 5 feet (1.52 m).
· Vent supports or plumbers strap (spaced 120º apart) may be used to support vent sections. See Figures 7.8 and 7.9.
· Wall shield firestops may be used to provide horizontal support to vent sections.
· SLP ceiling firestops have tabs that may be used to provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation! Improper support could allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

E. Disassemble Vent Sections
· Rotate either section (see Figure 7.10) so the seams on both pipe sections are aligned as shown in Figure 7.11.
· Pull carefully to separate the pieces of pipe.
Figure 7.10 Rotate Seams for Disassembly

120º

Figure 7.8 Securing Vertical Pipe Sections
120º

Figure 7.11 Align and Disassemble Vent Sections

Figure 7.9 Securing Horizontal Pipe Sections

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

45

F. Vertical Termination Requirements
Install Metal Roof Flashing
· See minimum vent heights for various pitched roofs (Figure 7.12) to determine the length of pipe to extend through the roof.
· Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 7.13.

NOTICE: Failure to properly caulk the roof flashing and pipe seams could permit entry of water.
· Caulk the gap between the roof flashing and the outside diameter of the pipe.
· Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 7.13.
· Caulk the overlap seam of any exposed pipe sections that are located above the roof line.

Note: When installing a silicone or EPDM pipe flashing boot on a metal roof, it is recommended to put a bead of 100%
silicone sealant where the boot contacts the vent pipe to
prevent the entry of water. Follow the manufacturer’s recommendations when installing the boot. Climate regions with frequent temperatures below – 50 °F (-45.6 °C) should use a silicone flashing boot.

CAULK

2 FT. MIN.
GAS DIRECT VENT TERMINATION CAP

20 INCHES MIN.
LOWEST DISCHARGE
OPENING

HORIZONTAL OVERHANG
VERTICAL WALL

X 12
ROOF PITCH IS X/ 12
H (MIN.) – MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Figure 7.13
Assemble and Install Storm Collar
CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. · Slide the storm collar onto the exposed pipe section
and align brackets. · Insert a bolt (provided) through the brackets and install
nut. Do not completely tighten.

Roof Pitch

H (Min.) Ft.

Flat to 6/12…………………………………. 1.0*

Over 6/12 to 7/12………………………. 1.25*

Over 7/12 to 8/12………………………… 1.5*

Over 8/12 to 9/12………………………… 2.0*

Over 9/12 to 10/12………………………. 2.5*

Over 10/12 to 11/12 ……………………. 3.25

Over 11/12 to 12/12 ……………………… 4.0

Over 12/12 to 14/12……………………… 5.0

Over 14/12 to 16/12……………………… 6.0

Over 16/12 to 18/12……………………… 7.0

Over 18/12 to 20/12……………………… 7.5

Over 20/12 to 21/12……………………… 8.0

• H minimum may vary depending on regional snowfall. Refer to local codes.

Figure 7.12 Minimum Height From Roof to Lowest Discharge Opening

Figure 7.14 Insert Bolt into Brackets
· Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 7.14).
· Tighten nut and make sure the collar is tight against the pipe section.
· Caulk around the top of the storm collar. See Figure 7.15.

46

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Install Vertical Termination Cap
· Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.
· Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 7.15).
Figure 7.15

G. Horizontal Termination Requirements
Heat Shield Requirements for Horizontal Termination
WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.
· DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 7.16).
· Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section is factory-attached to the wall shield firestop. The other section is factory-attached to the cap. See Figure 7.16.
If the wall thickness does not allow the required 1-1/2 in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.
· If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap and wall shield firestop must be trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST be maintained.
· Use an extended heat shield if the finished wall thickness is greater than 7-1/4 in. (184 mm).
· The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2 in. (38 mm) overlap between heat shields.
· Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.
· Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.
Important Notice: Heat shields may not be field constructed.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

47

Install Horizontal Termination Cap (DVP and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.
· 1-1/2 (38 mm) minimum overlap of flue telescoping section is required.
Failure to maintain overlap could cause overheating and fire.
· Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.
· Flash and seal as appropriate for siding material at outside edges of cap.
· When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149 installation codes and refer to Section 4 of this manual.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.
NOTICE: For certain exposures which require superior resistance to wind-driven rain penetration, a flashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

WALL SHIELD FIRESTOP

HEAT SHIELD OR EXTENDED
HEAT SHIELD

HEAT SHIELD 1-1/2 IN. (38 MM) MIN.
OVERLAP

SLIP SECTION CAN BE EXTENDED

INNER VENT OUTER VENT

INTERIOR

SHEATHING EXTERIOR

VENT DEPTH FROM BACK OF APPLIANCE TO OUTSIDE SURFACE OF EXTERIOR WALL (SEE CHART BELOW)
Figure 7.16 Venting Through the Wall

Cap Specification Chart (depth without using additional pipe sections)

DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2

Top Vent Rear Vent Top Vent Rear Vent

Depth

Depth

Depth

Depth

6000 Series 8000 Series

2-3/4 in. to 3-1/8 in. to 5-1/8 in. to 5-1/2 in. to

4-5/8 in.

5 in.

9-1/8 in.

9-1/2 in.

DVP-HPC1 Top Vent
Depth

DVP-HPC1 Rear Vent
Depth

DVP-HPC2 Top Vent
Depth

DVP-HPC2 Rear Vent
Depth

2-3/4 in. to 3-1/8 in. to 4-7/8 in. to 5-1/4 in. to

4-7/8 in.

5-1/4 in.

9 in.

9-3/8 in.

DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)

DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)

DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)

DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)

48

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Electrical Information

A. General Information
WARNING! Risk of Shock or Explosion! DO NOT wire 110-120 VAC to the valve or to the appliance wall switch. Incorrect wiring will damage controls.
NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.
· Wire the appliance junction box to unswitched 110120 VAC. This is required for proper operation of the appliance (IntelliFire® ignition).
· A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.
· Low voltage and 110-120 VAC voltage cannot be shared within the same wall box.
· In some instances, the spark ignition of the fireplace may cause intermittent, non-damaging, interference during the lighting sequence with a TV plugged into the same circuit. It is recommended that the fireplace and TV use different circuits to mitigate the interference potential. If interference is occurring on the same circuit, the use of surge protectors may help alleviate the interference.

Junction Box Installation
If the box is being wired from the INSIDE of the appliance:
· Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell. See Figure 8.1.
· Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 8.1.
· Make all necessary wire connections to the junction box/ receptacle and reattach the junction box/receptacle to the outer shell.

NOTICE: DO NOT wire 110-120 VAC to wall switch.

Romex Connector
14/2WG
Cover Plate outside firebox

WHT

BLK

WHT BLK

GRN wire inside box

Copper ground attached to GRN screw with GRN wire

Figure 8.1 Junction Box Detail
Accessories Requirements
· This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.
Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors could cause improper and dangerous operation. Verify proper operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire. Wire must have high temperature insulation.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

49

B. Wiring Requirements
IntelliFire Touch® Ignition System Wiring
· Wire the appliance junction box to 110-120 VAC for proper operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.
· Refer to Figure 8.3, IntelliFire Touch Wiring Diagram. · This appliance is equipped with an IntelliFire Touch
control valve which operates on a 6 volt/1.5 AMP system. · Plug the 6 volt transformer plug into the appliance junction
box to supply power to the unit OR install 4 AA cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should only be used as a power source in the event of an emergency power outage. Batteries should not be used as a primary long-term power source. Battery polarity must be correct when installing batteries. When using batteries as a power source, the 6-volt transformer must be unplugged from the receptacle.
Do not store batteries in the battery pack when the appliance is powered by the 6 volt transformer connected to permanent electrical service.

JUNCTION BOX 110-120 VAC

FLAME SENSE

IGNITER

ADAPTER

IFT-RC400 REMOTE CONTROL
(OPTIONAL)

IFT-RC150 WIRELESS WALL SWITCH
(OPTIONAL)

NEUTRAL HOT

SI

RF MODULE (FOR USE WITH OPTIONAL
REMOTE CONTROL)

ELECTRONIC CONTROL MODULE

VALVE
ORANGE (PILOT)

GREEN (MAIN)

6 PIN RED

APPLIANCE ON/OFF
CONTROL

BRN BLK

JUMPER WIRE

6V DC BATTERY PACK
RED
BLK

Figure 8.3 IntelliFire Touch Wiring Diagram

50

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use with a fan. See Figure 8.4:
· The power supply for the appliance must be brought into a switch box.
· The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire.
· At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.
· At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.
· Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

Minimum 14-3 AWG with Ground
Junction Box

Red Black White
Green

Switch
Black White Green

Red Black White Green

Switch Box Knockout

Power Supply Wires

Red

Figure 8.4 Junction Box Wired to Wall Switch

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

51

9 Gas Information

A. Fuel Conversion

C. Gas Connection

· Make sure the appliance is compatible with available gas types.
· Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.
B. Gas Pressure
· Optimum appliance performance requires proper input pressures.
· Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.
· Pressure requirements are:

Gas Pressure Minimum inlet pressure Maximum inlet pressure Manifold pressure

Natural Gas 5.0 in. w.c. 10.0 in. w.c. 3.5 in. w.c.

Propane 11.0 in. w.c. 13.0 in. w.c. 10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure could cause explosion.
· Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.
· Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING
Fire Risk. Explosion Hazard. High pressure will damage valve. · Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures above 1/2 psig. · Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

· Refer to Section 3 for location of gas line access in appliance.
· Gas line may be run through knockout(s) provided.
· The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300 ºF continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air infiltration.
· Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.
· Pipe incoming gas line into valve compartment.
· Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.
· A small amount of air will be in the gas supply lines.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
· Purge should be performed by qualified service technician.
· Ensure adequate ventilation.
· Ensure there are no ignition sources such as sparks or open flames.
Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation! Check all fittings and connections with a non-corrosive commercially available leak-check solution. DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.
D. High Altitude Installations

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI Z223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.
· If substituting for these components, please consult local codes for compliance.

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.
When installing above 2000 feet elevation:
· In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.
· In CANADA: Input ratings are certified without a reduction of input rate for elevations up to 4500 feet (1370 m)above sea level. Please consult provincial and/ or local authorities having jurisdiction for installations at elevations above 4500 feet (1370 m).
Check with your local gas utility to determine proper orifice size.

52

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

E. Air Shutter Setting
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 9.1.
· Loosen the wing nut.
· Move the air handle to the left to open the air shutter.
· Move the air handle to the right to close the air shutter.
· Tighten the wing nut.
NOTICE: If sooting occurs, provide more air by opening the air shutter.

AIR SHUTTER WING NUT

Figure 9.1 Air Shutter

Air Shutter Settings
6000 8000

NG 1/4 in. 1/4 in.

Propane 3/4 in. 3/4 in.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

53

Finishing

A. Facing Material
· Metal front faces may be covered with non-combustible materials only.
· Facing and/or finishing materials must not interfere with air flow through or removal of decorative fronts or access for service.
· Facing and/or finishing materials must never overhang into the glass opening.
· Observe all clearances when applying combustible materials.
· Seal joints between the finished wall and appliance top and sides using a 300 ºF minimum sealant. Refer to Figure 10.1.
WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with air flow through decorative fronts.
NOTICE: Surface temperatures around the appliance will become warm while the appliance is in operation. Ensure finishing materials used for all surfaces (floor, walls, mantels, etc.) will withstand temperatures up to 190°F.

B
FACTORY-INSTALLED NON-COMBUSTIBLE BOARD DO NOT REMOVE
A

6000 8000

inches millimeters
inches millimeters

A 39-3/4 1010 41-3/4 1060

Figure 10.2 Noncombustible Facing Diagram

B 41 1041 48 1219

FACING MATERIAL UP TO 1/2 IN. THICK
MAY BE COMBUSTIBLE – TOP AND SIDES 0 IN.

1 IN.

0 IN.

0 IN.

HIGH TEMPERATURE (300 ºF/ 149 ºC MIN.) TOP AND SIDE SEAL JOINT

BOTTOM 1 INCH (SHADED AREA) MAY BE COVERED WITH COMBUSTIBLE
OR NON-COMBUSTIBLE MATERIAL

Figure 10.1 Facing Materials

54

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.)
Mantels – Combustible or Painted Surfaces

Note: All measurements in inches.

TO CEILING 18

12

11

10

32

9

8

25

7
6 5
4 3

19 18 17
16 15

14 13

2-1/2

12 11 10

5

Measurement from fireplace opening to bottom of appliance: = 33-1/2 IN. (6000C) = 35-1/2 IN. (8000C)
Note: Measurement is taken from top of the opening, NOT the top of the fireplace.
Figure 10.3 Minimum Vertical and Maximum Horizontal Dimensions – Combustible or Painted Surfaces
Mantels – Non-Combustible

Note: All measurements in inches.

TO CEILING

18

12 11

10 9 8

32 25

7

19

18 17

16 15

14

6

Mantel Legs or Wall Projections

TOP VIEW

INTERIOR WALL

A

B

FIREPLACE OPENING

MANTEL LEG OR WALL PROJECTIONS

Combustible or Painted Surfaces

If A minimum is __, then B maximum is___.

A Inches 2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters 62

87 113 138 164 189

Inches

1

2

3

4

5

B
Millimeters 25

51

76 102 127

Non-Combustible

If A minimum is __, then B maximum is___.

A Inches 0 thru 6-7/16

Millimeters

0-164

Inches
B Millimeters

6 152

6-7/16
164

Figure 10.5 Clearances to Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Measurement from fireplace opening to bottom of appliance: = 33-1/2 IN. (6000C) = 35-1/2 IN. (8000C)
Note: Measurement is taken from top of the opening, NOT the top of the fireplace.
Figure 10.4 Minimum Vertical and Maximum Horizontal Dimensions – Non- Combustible

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

55

C. Decorative Fronts
Only decorative fronts certified for use with this appliance model may be used. Contact your dealer for a list of decorative fronts that may be used. Once you have determined what kind of decorative front and finishing material is going to be used on the fireplace, you may use the table below which shows the decorative front models and the finishing material thickness allowed.

Finishing Material: 1 Inch Thick or Less
Remove Finishing Strips. See Figure 10.9. NOTICE: Remove finishing strips before firing appliance.

Note: Finishing strips may be used to aid in positioning of non-combustible facing materials for some of the
facing and decorative front combinations specified in the table above. They must be removed following finishing work. See Figure 10.9.

DECORATIVE FRONT Folio Arcadia
Halston
Chateau Forge
Galleria CF
Iron Age

FIT
Inside Overlap Inside Overlap Inside Overlap Inside Overlap Inside Inside Overlap Inside

FINISH MATERIAL THICKNESS
0-6 inches max. 1 inch or less
1-6 inches max. 1 inch or less
1-6 inches max. 1 inch or less
1-6 inches max. 1 inch or less 1-6 inches max.
0-6 inches max. 1 inch or less
1-6 inches max.

SEE FIGURE
10.8 10.6 10.7 10.6 10.7 10.6 10.7 10.6 10.7 10.8 10.6 10.7

DOOR

1 in. MAX. FINISHING MATERIAL
(TOP EDGE)

Finishing materials 1 inch maximum thick. Stop finishing material flush with opening.

FINISHING STRIP NOT USED (See Figure 10.9 for removal instructions)
NON-COMBUSTIBLE FINISHING MATERIAL

Figure 10.6 Finishing Material 1 Inch Thick or Less

56

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Finishing Material Thickness: 1-6 Inches Maximum
NOTICE: Remove finishing strips before firing appliance.

FINISHING STRIPS USED
NON-COMBUSTIBLE FINISHING MATERIAL

FINISHING MATERIAL

FINISHING MATERIAL

DECORATIVE FRONT A
(Outside decorative front width)
C (Includes 1/8 in. opening each side of decorative front)

B
D A
(Outside decorative front width)

C
(Includes 1/8 in. opening each side of decorative front)

Finishing material thickness, 1-6 inches maximum B = Top of decorative front to bottom of fireplace. D = Bottom of Finishing Material to Bottom of Fireplace

8000 Models

6000 Models

Inches

Millimeters Inches Millimeters

A 44-1/16

1119

37-1/16

941

B 35-15/16

913

34-1/16

865

C 44-5/16

1126

37-5/16

948

D 36-5/16

922

34-7/16

875

Figure 10.7 Finishing Material Thickness Greater Than One Inch

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

57

Finishing Material Thickness: 0-6 Inches Maximum
NOTICE: Remove finishing strips before firing appliance.

Removal of Finishing Strips
NOTICE: Remove finishing strips before firing appliance. Remove glass frame assembly to access finishing strip screws.

FINISHING STRIP NOT USED (See Figure 10.9 for removal instructions)
NON-COMBUSTIBLE FINISHING MATERIAL

FINISHING STRIPS

DECORATIVE FRONT

FINISHING MATERIAL

FINISHING MATERIAL

Figure 10.8 Inside Fit (Folio / CF)

FINISHING STRIPS REMOVED

Figure 10.9 Removing Finishing Strips.

58

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

11 Appliance Setup
A. Remove Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.
· DO NOT strike, slam or scratch glass. · DO NOT operate fireplace with glass removed, cracked,
broken or scratched. · Replace as a complete assembly.
Removing Fixed Glass Assembly
· Pull the four glass assembly latches out of the groove on the glass frame. Remove glass assembly from the appliance See Figure 11.1.

D. Front Base Refractory Placement
1. Remove packaging from base refractory.
2. Locate the two tabs on the refractory support inside the front of the appliance. Use a pliers to bend the tabs as shown in Figure 11.2.
3. Place the base refractory across the front of the appliance. The tabs are used to support the base refractory.

LATCHES (BOTH BOTTOM
AND TOP)
GLASS ASSEMBLY

Figure 11.1 Fixed Glass Assembly

Figure 11.2 Refractory Support Tabs Left (Shown on top of photo) and Right (Shown on bottom of photo)

B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the firebox.
· The splatter guard is a piece of corrugated material used to protect the appliance during the installation process before finishing work on the whole hearth is complete. Splatter guards may be factory installed or accompany the decorative front of the appliance, depending on the fireplace model. Splatter guards must be removed before appliance is fired.
WARNING! Risk of Fire! Close the ball valve before installing the splatter guard to prevent accidental lighting. Remove the splatter guard before lighting the appliance.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

59

E. Burner Top Installation
1. Bend the two tabs upward as shown in Figure 11.3.
2. To install the fiber burner, mate the locating holes with the guide sleeves. Install fiber burner top so that it makes full contact with the underlying burner assembly.
3. Ensure that the ports in the steel burner are visible through the holes in the fiber burner top.

FIBER BURNER TOP

LOCATING HOLES

BEND TABS UP

AIR SCOOP

BURNER ASSEMBLY

PILOT COVER BURNER SHIELD

G. Ember Placement
WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT completely block burner ports with ember material. Replace ember material annually. Improperly placed embers interfere with proper burner operation.
Ember material is shipped with this gas appliance. To place the ember material:
· Embers CANNOT completely block burner ports. Care should be taken not to block the lighting trail of ports.
· Embers may only be placed in areas as shown in Figure 11.4.
· LP Only: Using dime-size pieces of Glowing Embers®, overlap the burner ports as shown in Figure 11.5. The impingement created by the embers will help blend the fire.
· Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

EMBERS

NO EMBERS IN SHADED AREA

GUIDE SLEEVES
Figure 11.3

F. Install the Refractory (Optional)
Optional fiber and black glass refractory kits are available for use with the 6000C-IFT and 8000C-IFT models. Install either the black glass refractory or brick refractory per instructions included with the kit.

Figure 11.4 Placement of Embers

Figure 11.5 Embers Overlapping Burner Port Holes (LP only).

60

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

H. Install the Log Assembly Log Set Assembly: LOGS-6C

LOG PLACEMENT INSTRUCTIONS

Models: 6000C, 6000C-IPI,6000C-IPILP, 6000CBV-IPI

6000C-IFT, 6000C-IFTLP

FIBER BURNER TOP

LOCATING HOLES

TAB BENT IN = NG

LOG PLACEMENT TABS

BURNER SHIELD BURNER ASSEMBLY

PILOT COVER

LOG PLACEMENT INDENTATIONS

TAB NOT BENT = LP

GUIDE SLEEVES

GRATE TINE

Figure 1

Figure 2. Log Placement Tabs

CAUTION: Logs are fragile, handle with care. Log #1 (SRV2164-701): Locate log placement tabs on the pilot cover. Bend tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits squarely and completely on pilot cover with tabs engaged (see Figure 4).

LOG PLACEMENT TABS

1

Figure 3

LOG PLACEMENT SLOTS

Figure 4

Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.

Bottom view of Logs # 2 and 3
SLOTS
2 3
GROOVES

LEFT GRATE TINE
1 2

Figure 5

Figure 6

Log #2 (SRV2164-702): Mate the slot located on the bottom of Log #2 with the left tab on top of Log #1. After slot and tab have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log # 2 toward the left until it rests against the far left grate tine.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

61

RIGHT GRATE TINE

1

2

3

NOSE

1

2

3

4

Figure 7

Figure 8

Log #3 (SRV2164-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1. After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar and slide Log # 3 toward the right until it rests against the far right grate tine (see Figure 7).
Log #4 (SRV2164-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right to left under Log #2 to fit completely and securely into the indentation (see Figure 8). Nose of log #4 should be pulled to fit securely against right hand side of log indentation.

FLAT AREA
1
2 4

3 5

LOG #6 CONTACTS TOP OF LOG #4

1
2 46

3 5

Figure 9

Figure 10

LOG CONTACTS GRATE TINES

Log #5 (SRV2164-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits completely and securely in the recessed indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.
Log #6 (SRV2164-706): Mate the groove located on the
lower end of Log #6 with the fourth grate tine (from left to right) as shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing movement or shifting.
Ensure the log set is in proper position by measuring from
the front of Log #1 to the refractory (or firebox if refractory is not installed) as shown in Figure 11. The measurement will be 6 inches for fireplaces with refractory installed if logs are placed properly. The measurement will be 6-3/4 inches for fireplaces that do not have refractory installed if logs are placed properly.

6 INCHES WITH OPTIONAL REFRACTORY
Figure 11

62

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

Log Set Assembly: LOGS-8C

LOG PLACEMENT INSTRUCTIONS

Models: 8000C, 8000C-LP, 8000C-IPI, 8000C-IPILP, 8000CBV-IPI 8000C-IFT, 8000C- IFTLP

FIBER BURNER TOP

LOCATING HOLES

TAB BENT IN = NG

BURNER SHIELD BURNER ASSEMBLY

PILOT COVER

LOG PLACEMENT INDENTATIONS LOG PLACEMENT TABS

TAB NOT BENT = LP

GUIDE SLEEVES

GRATE TINE

Figure 1

Figure 2. Log Placement Tabs

CAUTION: Logs are fragile, handle with care. Log #1 (SRV2168-701): Locate log placement tabs on the pilot cover. Bend tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits squarely and completely on pilot cover with tabs engaged. See Figure 4.

LOG PLACEMENT TABS

1

Figure 3

LOG PLACEMENT SLOTS

Figure 4

Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.

Bottom view of Logs # 2 and 3

SLOTS
2 3
GROOVES

LEFT GRATE TINE
1 2

Figure 5

Figure 6

Log #2 (SRV2168-702): Mate the slot located on the bottom of Log #2 with the left log placement tab on top of Log #1. After slot and tab have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log # 2 toward the left until it rests against the far left grate tine.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

63

RIGHT GRATE TINE

1

2

3

1

2

3

4
HORIZONTAL GRATE BAR

Figure 7

Figure 8

LOG #4 CONTACTS LOG #2

Log #3 (SRV2168-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1. After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar and far right grate tine. Log # 3 will sit down on top of both the grate tine and the horizontal grate bar (see Figure 7).
Log #4 (SRV2168-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right to left under Log #2 to fit completely and securely into the indentation (see Figure 8). The back or Log # 4 should rest against the far left grate tine as well as contact Log # 2.

LOG #6 CONTACTS TOP OF LOG #4

FLAT AREA

1

2

3

4 5

1

2

3

6

4

5

Figure 9

Figure 10

LOG CONTACTS GRATE TINES

Log #5 (SRV2168-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits completely and securely in the indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.
Log #6 (SRV2168-706): Mate the groove located on the lower end of Log #6 with the fourth tine (from left to right) as shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing movement or shifting.

64

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

I. IntelliFire Touch® Control System Setup
· Detailed instructions for electrical wiring and connections are provided in Section 8.
· Determine if this appliance is equipped with a Module Reset Switch. See Section 8. Verify this switch is in the ON position.
· Verify that the 3-Position switch on the IFT-ECM is switched to the REMOTE position. Detailed Operating Instructions for the IFT-ECM are provided in Section 3.J of the Owner’s Manual.
TOP VIEW

POSITION SWITCH

LED INDICATOR
Figure 11.6 IFT-ECM
If this appliance is being upgraded to an optional IntelliFire Touch Remote Control, and/or optional power vent, fan, or light kit are added as new accessory upgrade(s) to fireplace: 1. The RC400 remote will need to be paired to the ECM. 2. Follow the installation instructions provided with the
IntelliFire Touch remote and/or accessory kit(s).

J. Install Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.
· DO NOT strike, slam or scratch glass. · DO NOT operate fireplace with glass removed, cracked,
broken or scratched. · Replace as a complete assembly.
Replacing Fixed Glass Assembly
· Replace the glass assembly on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame. See Figure 11.1.
K. Install Decorative Front
WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts could cause fireplace to overheat.
This fireplace has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed. Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.
For more information refer to the instructions supplied with your decorative front.

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

65

12 Reference Materials
A. Vent Components Diagrams

Effective Height/Length
DVP Pipe (see chart)
20-3/4 in. (527 mm)

Pipe
DVP4 DVP6 DVP12 DVP24 DVP36 DVP48 DVP6A DVP12A

Effective Length

Inches Millimeters

4

102

6

152

12

305

24

610

36

914

48

1219

3 to 6 76 to 152

3 to 12 76 to 305

10-1/2 in.

(267 mm)

45 °

4-7/8 in. (124 mm)

10-7/8 in. (276 mm)

DVP45 (45º Elbow)

11-3/8 in. (289 mm)

Tab=1 in. (25.4 mm)

Finished Height: 19-3/4 in./502 mm UNIV-AS2 (Attic Insulation Shield)

10 in. (254 mm)

10 in. (254 mm)

1 in. (25 mm)

10 in. (254 mm)
UP
5 in. (127 mm)

1- 1/2 in. (38 mm)

DVP-FS (Ceiling Firestop)

12 in. (305 mm)

7-3/8 in. (187 mm)

9-1/4 in. (235 mm)
13-1/4 in. (337 mm)

1-1/4 in. (32 mm)
1/2 in. TYP (13 mm)

DVP90ST (90° Elbow)

DVP-HVS (Vent Support)
14 IN. (356 MM)

20 IN. (508 MM)

14 in. (356 mm)

12 in. (305 mm)

1 in. (25 mm)
8 in. (203 mm)

14 IN. (356 MM)

12 IN.

DVP-RDS

(305 MM)

ROOF DECK INSULATION SHIELD

6 in. (152 mm)
DVP-WS (Wall Shield Firestop)

Figure 12.1 DVP Vent Components

66

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

A. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required.

8 in. (203 mm)

Heat Shield

15-1/8 in. (384 mm)
12 in. (305 mm) DVP-TRAP Horizontal Termination Cap

Max Effective Length

Term Cap Trap1 Trap2

Minimum Effective Length
3-1/8 in. 79 mm
5-3/8 in. 137 mm

Maximum Effective Length
4-5/8 in. 117 mm
9-3/8 in. 238 mm

DVP-TRAP1

DVP-TRAP2

DVP-TRAPK1

DVP-TRAPK2

DVP-HPC1

DVP-HPC2

Figure 12.2 DVP Vent Components

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

67

A. Vent Components Diagrams (continued)

13-1/4 in. (337 mm)

24-5/8 in. (625 mm)

27-1/2 in. (699 mm)

RF6 Roof Flashing

24-5/8 in. (625 mm)

31 in. (787 mm)

RF12 Roof Flashing

13-1/4 in. (337 mm)

11-7/8 in. (302 mm)

5 in. (127 mm)

13-7/8 in. (352 mm)

DVP-TRAPFL Flashing

DVP-BEK2 DVP-HPC Cap Brick Extension

11-5/8 in. (295 mm)
7-1/8 in. (181 mm)
5-3/4 in. (146 mm)
26 in. 660 mm

12-1/8 in. (308 mm)

COOL-ADDM Cap Shield
13-7/8 in. (352 mm)

9-1/2 in. (241 mm)

14 in. (356 mm)

DVP-HSM-B Extended Heat Shield
Figure 12.3 DVP Vent Components

DRC-RADIUS Cap Shield

68

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

A. Vent Components Diagrams (continued)

1-1/2 in. (38 mm)

7-3/8 in. (187 mm)

14 in. (356 mm)
6 in. 152 mm
12 in. (305 mm)
DVP-TB1 Basement Vent Cap

17-3/4 in. (451 mm)

7-1/4 in. (184 mm)

12 in. 305 mm

5-1/4 in. (133 mm)

12-1/2 in. (318 mm)

DVP-TVHW VerticalTermination Cap (Highwind)

16-7/8 in. (429 mm)

14 in. (356 mm)

12 in. (305 mm)
12-1/8 in. (314 mm)

7-1/8 in. (181 mm)
8-3/4 in. (222 mm)

1-5/8 in. (41 mm)
DVP-HPC High Performance Cap

8-1/8 in. (206 mm)

13 in. (330 mm)

15 in. (381 mm)

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

5-1/2 in. 8-3/8 in. 140 mm 213 mm
87° 3°

10-1/2 in. 267 mm
10-7/8 in. 276 mm

DVP-HRC-SS Figure 12.4 DVP Vent Components

DVP-HRC-ZC-SS

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

69

A. Vent Components Diagrams (continued)

15 in. (381 mm)

8-1/8 in. (206 mm)

13 in. (330 mm)

DVP-HRC-SS Figure 12.5 DVP Vent Components

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

5-1/2 in. 8-3/8 in. 140 mm 213 mm
87° 3°

10-1/2 in. 267 mm
10-7/8 in. 276 mm

DVP-HRC-ZC-SS

COAXIAL to COLINEAR VENTING

LINK-DV30B Flex Liner Kit

768-380A Stainless Steel Flex Pipe
(Required)

DV-46DVA-GCL Coaxial/Colinear Appliance Connector

DVP-2SL Adapter

Figure 12.6 Coaxial to Colinear Vent Components

70

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

A. Vent Components Diagrams (continued) DECORATIVE TERMINATIONS/SHROUDS
Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting systems. This applies to both DVP and SLP venting systems.
Decorative Terminations Caps/Shrouds
DTO134 DTO146 DTS134 DTS146 LDS33 LDS46 LDS-BV

TOP VIEW

13-11/16 IN.

4 IN.
SIDE VIEW

1-3/4 IN.

13-5/8 IN.
3-11/16 IN. 5-7/8 IN.

Required Wire Harness and PVV-SLEEVE

Lengths Available

Part Number

10 ft. PV Wire Harness 20 ft. PV Wire Harness 40 ft. PV Wire Harness

PVI-WH10 PVI-WH20 PVI-WH40

60 ft. PV Wire Harness 80 ft. PV Wire Harness 100 ft. PV Wire Harness

PVI-WH60 PVI-WH80 PVI-WH100

Description

Part Number

12 in. Wire Harness Sleeve PVV-SLEEVE-12

48 in. Wire Harness Sleeve PVV-SLEEVE-48

12-1/8 IN.

PVV-SLP Vertical Power Vent

Note: A wire harness is required to power the PVV-SLP and connect it to the appliance. It is ordered separately from the PVV-SLP. Contact your dealer to order.

Note: The PVV-SLEEVE-12 and/or PVV-SLEEVE-48 is required to be installed with the PVV-SLP. It is ordered separately from the PVV-SLP. Contact your dealer to order.

Note: The PVV-SLP requires one of the following options to be installed on this appliance. Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store. OR Option B: IFT-RC150, IFT- ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These accessories are purchased separately from the PVI-SLP-B. Contact your dealer to order.
Note: The PVV-SLP requires one of the following options to be installed on this appliance. Option A: IFT-RC400 OR Option B: IFT-RC150 and IFT-ACM. These accessories are purchased separately from the PVV-SLP. Contact your dealer to order.
Figure 12.7 PVV-SLP Vent Components

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

71

A. Vent Components Diagrams (continued)

EFFECTIVE LENGTH 32 IN. (813 mm) MIN. 35 IN. (889 mm) MAX.

13-5/8 IN. 346 mm
12-1/2 IN. 318 mm

20-3/4 IN. 527 mm
PVI-SLP-B Power Vent Inline

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness PVI-WH10

20 FT PV Wire Harness PVI-WH20

40 FT PV Wire Harness PVI-WH40

60 FT PV Wire Harness PVI-WH60

80 FT PV Wire Harness PVI-WH80

100 FT PV Wire Harness PVI-WH100

Note: Wire harnesses required to power the PVI-SLP-B connect to the appliance and are ordered separately from PVI-SLP-B. Contact your dealer to order.
Note: The PVI-SLP-B requires one of the following options to be installed on this appliance. Option A: IFT-RC400 OR Option B: IFT-RC150 and IFT-ACM. These accessories are purchased separately from the PVI-SLP-B. Contact your dealer to order.

16 in. 406 mm

9-3/16 in. (233 mm)

4-1/2 in. 114 mm

15 in. (381 mm)

12-1/2 in. (318 mm)

13-5/8 in. (346 mm)

16-11/16 in. 424 mm

SLP-LPC
SLP Low Profile Cap (Approved for use with PVI-SLP-B only)

Figure 12.8 PVI-SLP-B Vent Components

72

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

16-11/16 in. (424 mm)

A. Vent Components Diagrams (continued)
Top View

6-1/4 IN. 159 mm

Front View
15-1/2 IN. 394 mm

1-1/2 IN. 38 mm
Side View

2-1/4 IN. 57 mm

14 IN. 356 mm

8 IN. 203 mm

4-3/4 IN. 121 mm
9-1/2 IN. 241 mm

11-1/2 IN. 292 mm

4-3/8 IN. 112 mm

10 IN. 254 mm

5-1/4 IN. 135 mm

PVLP-SLP Power Vent Low Profile

2-1/4 IN. 57 mm

Note: Wire harnesses required to power the PVLP-SLP connect to the appliance and are ordered separately from PVLP-SLP. Contact your dealer to order.

Note: A PVLP-HS heat shield is available and sold separately. Use if the PVLP- SLP is installed in a high traffic area.
Note: The PVLP-SLP requires one of the following options to be installed on this appliance. Option A: IFT-RC400 OR Option B: IFT-RC150 and IFT-ACM These accessories are purchased separately from the PVLP-SLP. Contact your dealer to order.

PVLP-BEK Brick Kit

PVLP-HS Heat Shield

Required Wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness PVI-WH10

20 FT PV Wire Harness PVI-WH20

40 FT PV Wire Harness PVI-WH40

60 FT PV Wire Harness PVI-WH60

80 FT PV Wire Harness PVI-WH80

100 FT PV Wire Harness PVI-WH100

Figure 12.9 PVLP-SLP Vent Components

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

73

A. Vent Components Diagrams (continued)

8-3/4 in. 222 mm

6-1/2 in. 165 mm

6-5/8 in. 168 mm
SLP45 45° Elbow

Effective Height/ Length
SLP PIPE

6-1/2 in. 165 mm

6 in. 152 mm

6-5/8 in. 168 mm

9-7/8 in. 251 mm

SLP90
90° Elbow Effective Height/Length

Pipe

inches

mm

SLP4 SLP6 SLP12 SLP24 SLP36 SLP48 SLP6A SLP12A

4 6 12 24 36 48 2 – 6 2 – 12

102 152 305 610 914 1219 51 – 152 51 – 305

6-1/2 in. 165 mm
9-1/4 in. 235 mm
6-1/2 in. 165 mm
25-3/16 in. 640 mm

10-7/8 in. 276 mm

8-7/8 in. 225 mm
SLP-HVS Horizontal Pipe
Support

1-1/2 in. 38 mm

DVP-SLP24 Adapter

8-1/16 in. 205 mm

8-11/16 in. 220 mm

12 in. 305 mm

8-11/16 in. 220 mm
SLP-FS Ceiling Firestop

1-1/2 in. 38 mm

Figure 12.10 SLP Series Vent Components

12 in. 305 mm
SLP-WS Wall Shield Firestop

74

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

5-1/2 in. 146 mm

A. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required.

8 in. (203 mm)

Heat Shield

15-1/8 in. (384 mm)

12 in. (305 mm)

Max Effective Length

SLP-TRAP Horizontal Termination Cap

Term Cap Trap1 Trap2

Minimum Effective Length
3-1/8 in. 79 mm 5-1/4 in. 133 mm

Maximum Effective Length
4-3/4 in. 121 mm 9-1/4 in. 235 mm

14-7/16 in. 367 mm

14-7/16 in. 367 mm
SLP-WT-BK Wall Thimble-Black

2-5/16 in. 59 mm

4 in. 102 mm

6-3/8 in. 163 mm
8-1/8 in. 206 mm

4-5/8 in. 117 mm
DVP-2SL Adapter

4-3/16 in. 106 mm
5-1/16 in. 128 mm

26 in. 660 mm
DVP-HSM-B Extended Heat Shield

12-5/8 IN. (321 mm)

20 IN. (508 mm)

12-5/8 IN. (321 mm)

10-5/8 IN. (270 mm)

SLP-RDS ROOF DECK INSULATION SHIELD

Figure 12.11 SLP Series Vent Components

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

75

A. Vent Components Diagrams (continued)

14 in. 356 mm
10-9/16 in. 269 mm
SLP-CCS-BK Cathedral Ceiling Support Box-Black

13 in. 330 mm
13 in. 330 mm
SLP-DCF-BK Ceiling Firestop
Black

12 in. 305 mm

1-5/16 in. 34 mm

12-1/2 in. 318 mm

SLP-TVHW Vertical
Termination Cap

10-11/16 in. 271mm

28-1/2 in. 724 mm

4-1/8 in. 105 mm

13-1/2 in. 343 mm
SLK-SNKD Snorkel
Termination Cap

4-3/4 in. 121 mm

Figure 12.12 SLP Series Vent Components

76

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

B. Accessories Optional Remote Controls, Wall Controls and Wall Switches
Follow the instructions supplied with the control installed to operate your fireplace: For safety: · Install a switch lock or a wall/remote control with child
protection lockout feature. · Keep remote controls out of reach of children. See your dealer if you have questions.
Optional Heat Management Kits
Follow the instructions supplied with the kit for operation. · Preparation of the appliance for installation of a heat
management kit is discussed in Section 6.B. Contact your dealer if you have questions.
Optional Glass Refractory Kit
Follow the instructions supplied to install the kit. Contact your dealer if you have questions.
Optional Brick Refractory Kit
Follow the instructions supplied to install the kit. Contact your dealer if you have questions.

Heat & Glo, a brand of Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com.

Printed in U.S.A. – Copyright 2023

Heat & Glo · 6000C-IFT, 8000C-IFT Installation Manual · 2502-980 Rev. P · 2/23

77

References

• P65Warnings.ca.gov
• heatnglo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>