Shenzhen Qiai Wireless Electronic Commerce Co Ltd CZ2202W Smart Socket User Manual
- June 1, 2024
- Shenzhen Qiai Wireless Electronic Commerce Co Ltd
Table of Contents
Shenzhen Qiai Wireless Electronic Commerce Co Ltd CZ2202W Smart Socket
Specifications
Name : WIFI Smart Socket
Maxload :16A
Material : PC
Input/Output :
AC100-240V 50/60Hz
Wifi support :
IEEE 802.11 b/g/n 2 .4GHz
Please check the following before using the device
- Your phone has been connected to a 2.4G Wifi.
- Your phone system version needs to be Android 5.0/iOS 10 or higher.
- Your phone must be able to access the APP store and download the APP
- If your router has set Mac address filtering. please enter the router settings to turn off it.
Pairing with eWelink APP
-
After power Is connected, there are 3 types of pairing methods.
1st type : Blue LED indicator blinks twice quickly and keeps on once to enter pairing mode(for the first use);
2ed type : Long press pairing button for more than 5 seconds until blue LED indicator blinks twice quickly and keeps on once to enter pairing mode;
3rd type : Turn on and off constantly three times and t hen t he blue LED indicator blinks twice quickly and keep on once to enter pairing mode. -
Connect your phone to 2.4GHz WiFi and turn on Bluetooth.
-
Open eWelink APP, tap add device In the top right corner of the screen
-
Select the WIFI connected to the phone, confirm the relevant Information, and click Next
-
After searching for the device, click on the right to add it
Compatible Pairing Mode
If you fail to enter Quick Pairing Mode(Touch) Please try “Compatible Pairing Mode” to Pair.
- Long Press Pairing button for 5s until the WiFi LED indicator changes in a cycle of two short flashes and one long flash and release. Long Press Pairing button for 5s again until the WiFi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode.
- Tap”+” and select “Compatible Pairing Mode” on APP. Select Wi- Fi SSID with ITEAD-***** and enter the password 12345678,and then go back to eWelink APP and tap “Next”. Be patient until pairing completes.
Pairing with RM2.4G remote control
-
open the added device and click the settings icon in the upper right corner.
-
Select “eWelink Remote”
-
Follow the prompts for the next step.
LED indicator “flashes once again” means the pairing is successful.
Note: If you need to delete the RM 2.4G remote control, enter the added interface and delete it.
Features
This device is WiFi smart switch, Use your smart phone in Turn devices on or off in your home anywhere, set timer on/off, Share with your family to control and so on.
-
App Control
-
Single/Countdown Timing
-
Linked Scene
-
Voice Control
-
Power-on State
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. !However, there is no guarantee that
interference will
not occur in a particular installation If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.