Tarzan Technology Co Ltd TZ302A Remote Control Transmitter Instruction Manual
- June 1, 2024
- Tarzan Technology Co Ltd
Table of Contents
Tarzan Technology Co Ltd TZ302A Remote Control Transmitter
Product Information
- Specifications:
- Power Source: 2 x 1.5V AAA batteries
- Functionality: Remote control for fan and light operation
- Timer Settings: 2, 4, or 8 hours
Product Usage Instructions
- Remote Control Operating Instructions
- Install 2 x 1.5V AAA batteries into the remote control.
- Remove the battery if the remote control is not used for long periods to prevent damage.
- Learning/Pairing Process for Multiple Fan Installation
- If you wish to install multiple fans in your home, follow these steps:
- Install each fan individually to ensure independent operation with one remote control for each fan.
- Learning Key:
- Fan button: Press to turn the fan and light off.
- Speed Functions:
- + button: Increases fan speed. Press once to increase speed. Pressing in Comfort Breeze mode cancels and resumes normal operation.
- – button: Decreases fan speed. Press once to decrease speed. Pressing in Comfort Breeze mode cancels and resumes normal operation.
- Comfort Breeze: Activate Comfort Breeze settings for warm or cool weather.
- Light button: Turn the light on or off.
- Colour Temperature button: Select the desired color temperature.
- Timer: Press to set automatic turn off after 2, 4, or 8 hours.
- User Manual (Note/Warning/Caution)
- Warning: Unapproved changes or modifications may void the user’s authority to operate the equipment.
- This device complies with FCC Rules and Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
FAQs
- Q: How do I reset the remote control?
- A: To reset the remote control, remove the batteries and reinsert them after a few seconds.
REMOTE CONTROL OPERATING INSTRUCTIONS
- Install 2 x 1.5V AAA battery into the remote control.
- To prevent damage to the remote control, remove the battery if not used for long periods.
FAN INSTALLATION
LEARNING/PAIRING PROCESS FOR MULTIPLE FAN INSTALLATION
Should you desire to install more than one fan in the home, please install them one by one using the steps below to ensure one remote operates each fan independently:
LEARNING KEY
- Step 1: Turn off the main power source to all fans to begin the learning process on any single fan.
- Step 2: Restore power to only one fan at a time for pairing, the rest remain off by use of your wall-mounted power switch.
- Step 3: Within 30 seconds of turning the fan’s AC power ON, press and hold the LEARNING KEY for 5 seconds to enter the learning function. Once the receiver has detected the set frequency, a beeping sound is emitted when the pairing is complete.
- Step 4: Repeat steps 1, 2 and 3 with each fan to ensure one remote does not operate multiple fans.
- Fan button. – Press and release the button to turn the fan and light off.
- Speed functions button, turn the fan on or off.
- + button, increases the fan speed
- Pressing and releasing the + button one time will increase the speed of the fan.
- Pressing the + button while in Comfort Breeze mode, will automatically cancel the Comfort Breeze mode and resume normal fan operation.
- – button, increases the fan speed
- Pressing and releasing the – button one time will increase the speed of the fan.
- Pressing the – button while in Comfort Breeze mode, will automatically cancel the Comfort Breeze mode and resume normal fan operation.
- Comfort breeze
- There are three Comfort Breeze settings. Pressing the button will activate the Comfort Breeze mode.
- Warm weather: The LED bar will illuminate and the lights will flow from high to low. (Counterclockwise Direction) A downward airflow creates a cooling effect. This allows you to set your air conditioner in a higher setting without affecting your comfort.
- Cool weather: The LED bar will illuminate and the lights will flow from low to high. (Clockwise Direction) An upward airflow moves warm air off the ceiling. This allows you to set your heating unit in a lower setting without affecting your comfort.
- Light functions
- Press and release button one time will turn the light on or off.
- Press and release button to select the desired colour temperature.
- Press + to increase the desired light level.
- Press – to decrease the desired light level.
- Timer
- Pressing the timer button will automatically turn the fan and light (if the light is on) off after 2, 4 or 8 hours.
FCC
User Manual (Note/Warning/Caution)
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>