Sensomics SensWatch Falcon User Manual

Sensomics SensWatch Falcon

Compatible OS and requirements

• Android 4.4 and above.
• 1OS 8.5 and above.
• Bluetooth 4.0 and above.

Specifications and functions

How to charge and detach the band

Pull the band gently and firmly away from the watch charging point to detach. Plug the charging point into a USB port to charge.

Preparation
Please charge the smart band for 2- 2.5 hours before turning it on for the first time. Battery sign will show on the screen while charging.

How to use

• Switch modes: Short-press on the button.
• Offline mode: The watch has a large internal memory that allows to record high resolution raw data without Bluetooth connection for approximately one week.
• Time setting: In the offline mode, switch to setting page and manually set time and date. Otherwise, it will be automatically synchronized after connecting to theSensLink App.
• Device ID: Displays device model and ID. Event mark: Long press the button to mark an event.
• ECG: To take – using a finger on your non-watch hand, touch and hold the Electrode.

Connection Instruction

• Please go to the App Store or Google Play, search “SensLink” to download the App, or scan the Android QR code below.
• After logging into SensLink app, search for the device model number, then choose the device to connect in the app.

Remarks

• If there is any problem with the quality of the product or the use of the product, please contact us via email: [email protected].
• The product’s waterproof rating is IP67. It is resistant to splashes, but not long submersion or diving in water. In addition, this product does not prevent hot water incursion.
• The company reserves the right to modify the contents of this manual without prior notice. Some functions may change with different software versions.
• This product contains a polymer battery. Do not place this product in a high temperature environment for a long time. Do not place this product near an open flame.
• The measurements are not intended for medical use, including self-diagnosis or consultation with a doctor.

FAQ

• Cant find the smart band or can’t establish connection?
• Please make sure the Bluetooth is turned on, and the
• Bluetooth sign is not on the smart band. If the sign is on, the smart band is connected already. Please enter your phone’s Bluetooth settings and forget this device.
• Re-enter the SensLink app and try to connect again.
• Android system:
• Still unable to connect, enter application settings for
• SensLink (long click the SensLink app, or enter through
• App settings and find SensLink). Click Permissions, allow access to Location, Files and Media, and Nearby devices. May require phone restart.
• After binding the smart band, it shows not connected or remaining battery is 0%?
• The smart band and the device are not connected successfully, please bind the devices again.
• No data shown on SensLink app? Pull down the main page to manually synchronize the data.

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the lımits for a Class B digıtal device, pursuant to Part 15 of the FCC Rules. These limits are desıgned to provide reasonable protection against harmful interterence in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful nterterence to radio communications. However, there is no guarante that interference will not occur in a particular installation. Ilf this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interterence by one or more of the followıng measures: –

• Reorient or relocate the receiving antenna.
• Increase the separatıon between the equipment and recever.
• Connect the equipment into an outlet on a Cırcuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/’TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This devIce may not cause harmful ınterterence, and
• This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>