LG 55SK9500PUA Smart LED TV Owner’s Manual
- June 16, 2024
- LG
Table of Contents
55SK9500PUA Smart LED TV
Product Information
Specifications
-
Model: 65SK9500PUA, 55SK9500PUA, 65SK9550PUA, 65SK9000PUA,
55SK9000PUA, 65SK8550PUA, 55SK8550PUA, 75SK8070PUA, 75SK8050PUA,
75SK8070AUB, 65SK8000AUB, 55SK8000AUB, 65SK8000PUA, 55SK8000PUA,
49SK8000PUA, 65SK8050PUA, 55SK8050PUA, 49SK8050PUA, 65UK7700AUB,
65UK7700PUD, 55UK7700AUB, 55UK7700PUD, 49UK7700AUB, 49UK7700PUD,
65UK7500PUA, 55UK7500PUA, 49UK7500PUA, 86UK6570PUB, 75UK6570PUB,
75UK6570PUA, 86UK6570AUA, 75UK6570AUA, 70UK6570PUB, 70UK6550PUA,
70UK6570AUB, 65UK6500AUA, 55UK6500AUA, 50UK6500AUA, 43UK6500AUA,
65UK6550PUB, 55UK6550PUB, 50UK6550PUB, 43UK6550PUB, 65UK6300PUE,
55UK6300PUE, 50UK6300PUE, 49UK6300PUE, 43UK6300PUE, 65UK6300BUB,
65UK6350PUC, 55UK6300BUB, 55UK6350PUC, 50UK6300BUB, 49UK6300BUB,
49UK6350PUC, 43UK6300BUB, 75UK6270PUB, 65UK6200PUA, 43UK6350PUC,
60UK6200PUA, 60UK6250PUB, 55UK6200PUA, 55UK6250PUB, 49UK6200PUA,
49UK6250PUB, 43UK6200PUA, 43UK6250PUB, 32LK610BPUA, 49LK5750PUA,
43LK5750PUA, 86UK6570PUA, 32LK610BBUA -
Screen Type: LCD with LED backlights
Product Usage Instructions
Safety Instructions
Before operating the TV, please read and follow the safety
instructions below:
- If the power cord or plug is damaged, if liquid has been
spilled on the TV, if objects have fallen into the TV, if the TV
has been exposed to rain or moisture, if the TV does not operate
normally, or if the TV has been dropped, do not use it and contact
qualified service personnel.
Important Safety Instruction
Warning! Safety Instructions:
-
CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL. -
The symbol is intended to alert the user to the presence of
uninsulated dangerous voltage within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
shock to persons. The symbol is intended to alert the user to the
presence of important operating and maintenance (servicing)
instructions in the literature accompanying the device. -
WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. -
The power plug is the disconnecting device. In case of an
emergency, the power plug must remain readily accessible.
Preparing
Before using the TV, make sure you have the following optional
extras:
-
Magic Remote Control (depending upon model) – Check whether
your TV model supports Bluetooth in the Wireless Module
Specification to verify whether it can be used with the Magic
Remote. -
Wall Mounting Bracket (depending upon model) – Make sure to use
screws and wall mount bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in the user
manual.
Frequently Asked Questions (FAQ)
-
1. Can I use a Magic Remote Control with my TV?
The compatibility of the Magic Remote Control depends on your TV
model. Please check the Wireless Module Specification in your user
manual to verify if your TV supports Bluetooth and can be used with
the Magic Remote.
-
1. What should I do if my TV doesn’t operate normally?
If your TV does not operate normally, please do not attempt to
fix it yourself. Contact qualified service personnel for
assistance.
-
1. Can I mount my TV on the wall?
Depending on the model, you may be able to mount your TV on the
wall. Make sure to use screws and a wall mount bracket that meet
the VESA standard. Refer to the user manual for the standard
dimensions and instructions on wall mounting.
OWNER’S MANUAL
Safety and Reference
LED TV LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your TV and retain it for future reference.
65SK9500PUA 55SK9500PUA 65SK9550PUA 65SK9000PUA 55SK9000PUA 65SK8550PUA 55SK8550PUA 75SK8070PUA 75SK8050PUA 75SK8070AUB 65SK8000AUB
55SK8000AUB 65SK8000PUA 55SK8000PUA 49SK8000PUA 65SK8050PUA 55SK8050PUA 49SK8050PUA 65UK7700AUB 65UK7700PUD 55UK7700AUB 55UK7700PUD
49UK7700AUB 49UK7700PUD 65UK7500PUA 55UK7500PUA 49UK7500PUA 86UK6570PUB 75UK6570PUB 75UK6570PUA 86UK6570AUA 75UK6570AUA 70UK6570PUB
MFL70340102
(1803-REV02)
70UK6550PUA 70UK6570AUB 65UK6500AUA 55UK6500AUA 50UK6500AUA 43UK6500AUA 65UK6550PUB 55UK6550PUB 50UK6550PUB 43UK6550PUB 65UK6300PUE
55UK6300PUE 50UK6300PUE 49UK6300PUE 43UK6300PUE 65UK6300BUB 65UK6350PUC 55UK6300BUB 55UK6350PUC 50UK6300BUB 49UK6300BUB 49UK6350PUC
43UK6300BUB 75UK6270PUB 65UK6200PUA 43UK6350PUC 60UK6200PUA 60UK6250PUB 55UK6200PUA 55UK6250PUB 49UK6200PUA 49UK6250PUB 43UK6200PUA
43UK6250PUB 32LK610BPUA 49LK5750PUA 43LK5750PUA 86UK6570PUA 32LK610BBUA
www.lg.com
Printed in Korea Copyright 2018 LG Electronics Inc. All Rights Reserved.
ENGLISH
Important Safety Instruction
· Read these instructions. · Keep these instructions. · Heed all warnings. ·
Follow all instructions. · Do not use this apparatus near water. · Clean only
with dry cloth. · Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions. · Do not install near any heat sources
such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat. · Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet. · Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus. · Only use attachments/accessories specified by the manufacturer. ·
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
· Unplug this apparatus during lightning storms or when unused for long
periods of time. · Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING: This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm. Wash hands after
handling. By using this product, you agree that all disputes between you and
LG arising out of or relating in any way to this product (including but not
limited to warranty disputes) shall be resolved exclusively through binding
arbitration on an individual basis. The terms of the arbitration agreement
(including details on the procedure for resolving disputes) is available at
www.lg.com/us/arbitration (USA) or www.lg.ca/arbitration (Canada). 2
ENGLISH
Warning! Safety Instructions
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons. The symbol is
intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
device. WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
· TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES
AWAY FROM THIS PRODUCT AT ALL TIMES.
· Do not place the TV and/or remote control in the following environments: –
Keep the product away from direct sunlight. – An area with high humidity such
as a bathroom – Near any heat source such as stoves and other devices that
produce heat. – Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil. – An area exposed to rain or wind. – Do not expose to
dripping or splashing and do not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).
– Near flammable objects such as gasoline or candles, or expose the TV to
direct air conditioning. – Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/ explosion,
malfunction or product deformation.
· Ventilation – Install your TV where there is proper ventilation. Do not
install in a confined space such as a bookcase. – Do not install the product
on a carpet or cushion. – Do not block or cover the product with cloth or
other materials while unit is plugged in.
· Take care not to touch the ventilation openings. When watching the TV for a
long period, the ventilation openings may become hot.
· Protect the power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the
device.
· Do not move the TV whilst the Power cord is plugged in. · Do not use a
damaged or loosely fitting power cord. · Be sure do grasp the plug when
unplugging the power cord. Do
not pull on the power cord to unplug the TV. · Do not connect too many devices
to the same AC power outlet as
this could result in fire or electric shock. · Disconnecting the Device from
the Main Power
– The power plug is the disconnecting device. In case of an emergency, the
power plug must remain readily accessible.
· Do not let your children climb or cling onto the TV. Otherwise, the TV may
fall over, which may cause serious injury.
· Outdoor Antenna Grounding (Can differ by country): – If an outdoor antenna
is installed, follow the precautions below. An outdoor antenna system should
not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can come in contact with such power lines or
circuits as death or serious injury can occur. Be sure the antenna system is
grounded to provide some protection against voltage surges and built-up static
charges. Section 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes and requirements for the grounding
electrode. Antenna grounding according to the National Electrical Code,
ANSI/NFPA 70
3
ENGLISH
· Grounding (Except for devices which are not grounded.) – TV with a three-
prong grounded AC plug must be connected to a three-prong grounded AC outlet.
Ensure that you connect the earth ground wire to prevent possible electric
shock.
· Never touch this apparatus or antenna during a lightning storm. You may be
electrocuted.
· Make sure the power cord is connected securely to the TV and wall socket if
not secured damage to the Plug and socket may occur and in extreme cases a
fire may break out.
· Do not insert metallic or inflammable objects into the product. If a foreign
object is dropped into the product, unplug the power cord and contact the
customer service.
· Do not touch the end of the power cord while it is plugged in. You may be
electrocuted.
· If any of the following occur, unplug the product immediately and contact
your local customer service. – The product has been damaged. – If water or
another substance enters the product (like an AC adapter, power cord, or TV).
– If you smell smoke or other odors coming from the TV – When lightning storms
or when unused for long periods of time. Even the TV is turned off by remote
control or button, AC power source is connected to the unit if not unplugged
in.
· Do not use high voltage electrical equipment near the TV (e.g., a bug
zapper). This may result in product malfunction.
· Do not attempt to modify this product in any way without written
authorization from LG Electronics. Accidental fire or electric shock can
occur. Contact your local customer service for service or repair. Unauthorized
modification could void the user’s authority to operate this product.
· Use only an authorized attachments / accessories approved by LG Electronics.
Otherwise, this may result in fire, electric shock, malfunction, or product
damage.
· Never disassemble the AC adapter or power cord. This may result in fire or
electric shock.
· Handle the adapter carefully to avoid dropping or striking it. An impact
could damage the adapter.
· To reduce the risk of fire or electrical shock, do not touch the TV with wet
hands. If the power cord prongs are wet or covered with dust, dry the power
plug completely or wipe dust off.
· Batteries – Store the accessories (battery, etc.) in a safe location out of
the reach of children. – Do not short circuit, disassemble, or allow the
batteries to overheat. Do not dispose of batteries in a fire. Batteries should
not be exposed to excessive heat.
· Moving – When moving, make sure the product is turned off, unplugged, and
all cables have been removed. It may take 2 or more people to carry larger
TVs. Do not press or put stress on the front panel of the TV. Otherwise, this
may result in product damage, fire hazard or injury.
· Keep the packing anti-moisture material or vinyl packing out of the reach of
children.
· Do not allow an impact shock, any objects to fall into the product, and do
not drop anything onto the screen.
· Do not press strongly upon the panel with a hand or a sharp object such as a
nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.
· Cleaning – When cleaning, unplug the power cord and wipe gently with a
soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not
clean your TV with chemicals including glass cleaner, any type of air
freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner,
benzene, alcohol etc., which can damage the product and/or its panel.
Otherwise, this may result in electric shock or product damage.
4
ENGLISH
Preparing
Optional Extras
· When the TV is turned on for the first time after being shipped from the
factory, initialization of the TV may take approximately one minute.
· Image shown may differ from your TV. · Your TV’s OSD (On Screen Display) may
differ slightly from that
shown in this manual. · The available menus and options may differ from the
input source
or product model that you are using. · New features may be added to this TV in
the future. · The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / off button, turning off the
device and unplugging the power cord. · The items supplied with your product
may vary depending upon the model. · Product specifications or contents of
this manual may be changed without prior notice due to upgrade of product
functions. · For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width.
· Use an extension cable that supports USB 2.0 if the USB cable or USB flash
drive does not fit into your TV’s USB port. · Use a certified cable with the
HDMI logo attached. If you do not use a certified HDMI cable, the screen may
not display or a connection error may occur. · Recommended HDMI cable types (3
m (9.84 feet) or less) – High-Speed HDMI®/TM cable – High-Speed HDMI®/TM cable
with Ethernet
Optional extras can be changed or modified for quality improvement without any
notification. Contact your dealer for buying these items. These devices work
only with certain models. The model name or design may be changed due to the
manufacturer’s circumstances or policies.
Magic Remote Control
(Depending upon model)
AN-MR18BA Check whether your TV model supports Bluetooth in the Wireless
Module Specification to verify whether it can be used with the Magic Remote.
Wall Mounting Bracket
(Depending upon model) Make sure to use screws and wall mount bracket that
meet the VESA standard. Standard dimensions for the wall mount kits are
described in the following table.
A B
B A
B A
A <= 10 mm (0.39 inches) B <= 18 mm (0.7 inches)
· How to use the ferrite core, (Depending upon model). – Use the ferrite core to reduce the electromagnetic interference in the power cord. Wind the power cord on the ferrite core once.
[Wall side] [TV side]
10 cm (+ / -2 cm)
Model
VESA (A x B) (mm) Standard screw Number of screws Wall mount bracket
(optional)
49SK80 49UK77 49UK75 43/50UK65 43/50UK63 43UK62 32LK61 43LK57
200 x 200
M6
4
LSW240B MSW240
55SK80 55UK77 55UK75 55UK65 49/55UK63 49/55UK62 49LK57*
300 x 300
M6
4
OLW480B MSW240
5
ENGLISH
Model
VESA (A x B) (mm) Standard screw Number of screws Wall mount bracket
(optional)
55/65SK95 55/65SK90 55/65SK85 65SK80 65UK77 65UK75 65UK65 65UK63
60/65UK62* 300 x 300
M6
4
OLW480B
75SK80 70/75/86UK65 75UK62*
600 x 400 M8 4 LSW640B
· Use at least two people to move a large TV. · When transporting the TV by
hand, hold the TV as shown in the
following illustration.
· When transporting the TV, do not expose the TV to jolts or excessive
vibration.
· When transporting the TV, keep the TV upright; never turn the TV on its side
or tilt towards the left or right.
· When handling the TV, be careful not to damage the protruding buttons.
Lifting and moving the TV
When moving or lifting the TV, read the following to prevent the TV from being
scratched or damaged and for safe transportation regardless of its type and
size.
· It is recommended to move the TV in the box or packing material that the TV
originally came in.
· Before moving or lifting the TV, disconnect the power cord and all cables.
· When holding the TV, the screen should face away from you to avoid damage.
· Avoid touching the screen at all times, as this may result in damage to the
screen.
· Do not place the product on the floor with its front facing down without
padding. Failure to do so may result in damage to the screen.
· Do not move the TV by holding the cable holders, as the cable holders may
break, and injuries and damage to the TV may occur, (Depending upon model).
· When attaching the stand to the TV set, place the screen facing down on a
cushioned table or flat surface to protect the screen from scratches.
Mounting on the Table
· Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.
1 Lift and tilt the TV into its upright position on a table. · Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.
10 cm
(4 inches)
10 cm
10 cm
10 cm
10 cm
(Depending upon model) 2 Connect the power cord to a wall outlet.
6
ENGLISH
· Do not apply foreign substances (oils, lubricants, etc.) to the screw parts
when assembling the product. (Doing so may damage the product.)
· If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which may
cause injury.
· Do not use any unapproved items to ensure the safety and product life span.
· Any damage or injuries caused by using unapproved items are not covered by
the warranty.
· Make sure that the screws are fastened tightly. (If they are not fastened
securely enough, the TV may tilt forward after being installed.)
· Do not fasten the screws with excessive force otherwise they may strip and
become loose.
Securing TV to the Wall
Mounting to the Wall
An optional wall mount can be used with your LG Television. Consult with your
local dealer for a wall mount that supports the VESA standard used by your TV
model. Carefully attach the wall mount bracket at the rear of the TV. Install
the wall mount bracket on a solid wall perpendicular to the floor. If you are
attaching the TV to other building materials, please contact qualified
personnel to install the wall mount. Detailed instructions will be included
with the wall mount. We recommend that you use an LG brand wall mount. The LG
wall mount is easy to adjust or to connect the cables. When you do not use
LG’s wall mount bracket, use a wall mount bracket where the device is
adequately secured to the wall with enough space to allow connectivity to
external devices. If you are using a non-adjustable mount, attach the mount to
the wall. Attach the cables to the TV first, then attach the TV to the mount.
10 cm (4 inches)
10 cm
10 cm
10 cm
10 cm
(Depending upon model)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of
the TV. · If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall. Match the location of
the wall bracket and the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make
sure to keep the rope horizontal with the flat surface.
· Use a platform or cabinet that is strong and large enough to support the TV
securely.
· Brackets, bolts and ropes are not provided. You can obtain additional
accessories from your local dealer.
(Depending upon model)
· Remove the stand before installing the TV on a wall mount by performing the
stand attachment in reverse.
· For more information of screws and wall mount bracket, refer to the Separate
purchase.
· If you intend to mount the product to a wall, attach VESA standard mounting
interface (optional parts) to the back of the product. When you install the
set to use the wall mounting bracket (optional parts), fix it carefully so as
not to drop.
· When mounting a TV on the wall, make sure not to install the TV by hanging
the power and signal cables on the back of the TV.
· Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
7
ENGLISH
Connections
· Do not use a sharp object when you detached the cable cover. This could
damage the cable or the cabinet. It may also cause personal harm, (Depending
upon model).
· When installing the wall mounting bracket, it is recommended to cover the
stand hole using tape, in order to prevent the influx of dust and insects,
(Depending upon model).
Stand hole
You can connect various external devices to the TV. For more information on
external device’s connection, refer to the manual provided with each device.
Antenna/Cable
Connect an antenna, cable, or cable box to watch TV while referring to the
following. The illustrations may differ from the actual items and an RF cable
is optional.
· Make sure not to bend the copper wire of the RF cable.
Copper wire
· Complete all connections between devices, and then connect the power cord to
the power outlet to prevent damage to your TV.
· Use a signal splitter to use 2 TVs or more. · DTV Audio Supported Codec:
MPEG, Dolby Digital · This TV cannot receive ULTRA HD (3840 x 2160 pixels)
broadcasts
directly because the related standards have not been confirmed, (Depending
upon model).
Other connections
Connect your TV to external devices. For the best picture and audio quality,
connect the external device and the TV with the HDMI cable.
HDMI
· HDMI Audio Supported Format: (Depending upon model) DTS (44.1 kHz / 48 kHz /
88.2 kHz / 96 kHz), DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz
/ 192 kHz), True HD (48 kHz), Dolby Digital / Dolby Digital Plus (32 kHz /
44.1 kHz / 48 kHz), PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
8
ENGLISH
(Only UHD models)
·
( ) Picture Additional Settings
HDMI ULTRA HD Deep Color
– On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)
– Off : Support 4K @ 60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Color, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case, change the TV’s
HDMI ULTRA HD Deep Color setting to off.
– This feature is available only on certain models which support
HDMI ULTRA HD Deep Color.
External Devices
Supported external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and other
external devices. For more information on external device’s connection, refer
to the manual provided with each device.
· If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder or VCR. For
more information about recording, refer to the manual provided with the
connected device.
· The external device connections shown may differ slightly from illustrations
in a manual.
· Connect external devices to the TV regardless about the order of the TV
port.
· If you connect a gaming device to the TV, use the cable supplied with the
gaming device.
· Refer to the external equipment’s manual for operating instructions.
· In PC mode, there may be noise associated with the resolution, vertical
pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu until the picture is clear.
Depending upon the graphics card, some resolution settings may not allow the
image to be positioned on the screen properly.
· Some USB Hubs may not work. If a USB device connected through a USB Hub is
not detected, connect it directly to the USB port on the TV.
· When connecting via a wired LAN, it is recommended to use a CAT 7 cable.
· The TV may be capable of operating without a set-top-box from a multichannel
video programming distributor (MVPD).
· For LK series, HDR (High Dynamic Range) pictures can be viewed over the
Internet or via USB and HDMI 1.4 compatible devices.
Remote RS-232C setup
To obtain the RS-232C external control setup information, please visit
www.lg.com. Download and read the manual, (Depending upon model).
· Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
· When connecting external devices such as video game consoles, make sure the
connecting cables are long enough. Otherwise, the product may fall over, which
may cause injury or damage the product.
Using Button
You can simply operate the TV functions, using the button.
Basic functions
Power On (Press) Power Off 1 (Press and Hold) Menu Control (Press 2) Menu
Selection (Press and Hold 3) 1 All running apps will close. 2 You can access
and adjust the menu by pressing the button when TV is on. 3 You can use the
function when you access menu control.
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust the Menu
items using the button.
Turns the power off. Changes the input source. Scrolls through the saved
channels.
Adjusts the volume level. 9
ENGLISH
Using Remote Control
- To use the button, press and hold for more than 3 seconds.
(Depending upon model) The descriptions in this manual are based on the
buttons on the remote control. Please read this manual carefully and use the
TV correctly. To install batteries, open the battery cover, replace batteries
(1.5 V AAA) matching the and ends to the label inside the compartment, and
close the battery cover. To remove the batteries, perform the installation
actions in reverse. This remote uses infrared light. When in use, it should be
pointed in the direction of the TV’s remote sensor.
Make sure to point the remote control toward the remote control sensor on the
TV.
1
2
(POWER) Turns the TV on or off. Returns to the last TV channel.
Activates or deactivates the subtitles. (Q. Settings) Accesses the Quick
Settings.
(Search) Shows the search mode. (Input) Changes the input source. Number
button Enters numbers. (Dash) Inserts a dash between numbers such as 2-1 and
2-2.
Accesses the saved channel list. Alternates between the two last channels
selected (pressing repeatedly).
- You can access the application or Live TV channel by using the number buttons as registered.
Adjusts the volume level. Accesses your favorite channel list.
Shows information on the current program.
(MUTE) Mutes all sounds. - (MUTE) Accesses the Accessibility menu. Scrolls through the saved channels.
Moves to the previous or next screen. 1 , 2 Streaming Service buttons Connects to the Video Streaming Service.
(Home) Accesses the Home menu. * (Home) Shows the previous history.
Displays the program event according to time scheduler.
By zooming in on the selected area, you can view it in full screen. Navigation button (up / down / left / right) Scrolls through menus or options.
Selects menus or options and confirms your input. Returns to the previous screen. Clears all on-screen displays and returns to TV viewing. Enables SAP (Secondary Audio Program) Feature,
(Depending upon model). Starts to record. (Only Time Machine Ready supported model)
(Depending upon model) , , , , Control buttons for media contents , , , These access special functions in some
menus.
(Some buttons and services may not be provided depending upon models or regions.)
10
ENGLISH
Using Magic Remote Control * To use the button, press and hold for more than 3 seconds.
(Depending upon model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
When the message”Magic remote battery is low. Please change the battery.”is
displayed, replace the batteries.
To install batteries, open the battery cover, replace batteries (1.5 V AA)
matching the and ends to the label inside the compartment, and close the
battery cover. Be sure to point the magic remote toward the remote control
sensor on the TV. To remove the batteries, perform the installation actions in
reverse. This remote uses infrared light. When in use, it should be pointed in
the direction of the TV’s remote sensor.
1
2
(Some buttons and services may not be provided depending upon models or regions.)
(POWER) Turns the TV on or off. You can turn your set-top box on or off by
adding the set-
top box to the universal remote control for your TV. Number buttons Enters
numbers. – (Dash) Inserts a dash between numbers such as 2-1 and 2-2.
Accesses the saved channel list.
(Screen Remote) Displays the Screen Remote.
– Accesses the Universal Control Menu in some regions. * (Screen Remote) SAP (Secondary Audio Program) Feature can be enabled by pressing the key.
- You can access the application or Live TV channel by using the number buttons as registered.
Adjusts the volume level. (MUTE) Mutes all sounds. (MUTE) Accesses the Accessibility menu.
Scrolls through the saved channels. (Voice recognition)
Network connection is required to use the voice recognition function.
Once the voice display bar is activated on the TV screen, press and hold
the button and speak your command out loud.
(HOME) Accesses the Home menu.
- (HOME) Shows the previous history.
Wheel (OK) Press the center of the Wheel button to select a
menu. You can change channels by using the Wheel button.
(up/down/left/right) Press the up, down, left or right
button to scroll the menu. If you press
buttons while the
pointer is in use, the pointer will disappear from the screen and Magic
Remote will operate like a general remote control. To display the
pointer on the screen again, shake Magic Remote to the left and right.
Returns to the previous level.
- Clears on-screen displays and returns to last input viewing.
Displays the program event according to time scheduler.
1 , 2 Streaming Service buttons Connects to the Video
Streaming Service.
(INPUT) Changes the input source.
- (INPUT) Displays all the lists of external inputs. (Q. Settings) Accesses the Quick Settings. * (Q. Settings) Displays the All Settings menu. , , , These access special functions in some menus. , Control buttons for media contents
By zooming in on the selected area, you can view it in full screen. - You can zoom in on the area where the remote control is pointed.
11
ENGLISH
Registering Magic Remote Control
How to register the Magic Remote Control
To use the Magic Remote, first pair it with your TV. 1 Put batteries into the
Magic Remote and turn the TV on. 2 Point the Magic Remote at your TV and press
the Wheel (OK) on
the remote control. If the TV fails to register the Magic Remote, try again
after turning
the TV off and back on. How to deregister the Magic Remote Control
Press the and (HOME) buttons at the same time, for five seconds, to unpair the
Magic Remote with your TV. Pressing and holding the button will let you
cancel and re-
register Magic Remote at the same time.
· Do not mix new batteries with old batteries. This may cause the batteries to
overheat and leak.
· Failure to match the correct polarities of the battery may cause the battery
to burst or leak, resulting in fire, personal injury, or ambient pollution.
· This apparatus uses batteries. In your community there might be regulations
that require you to dispose of these batteries properly due to environmental
considerations. Please contact your local authorities for disposal or
recycling information.
· Batteries inside or inside the product shall not be exposed to excessive
heat such as sunshine, fire or the like.
Troubleshooting
Cannot control the TV with the remote control.
· Check if anything such as tape has been placed over the receiver. · Check if
there is any obstacle between the product and the remote
control. · Replace the batteries with new fresh ones. No image display and no
sound is produced.
· Check if the product is turned on. · Check if the power cord is connected to
a wall outlet. · Check if there is a problem in the wall outlet by connecting
other
products. The TV turns off suddenly.
· Check the power control settings. The power supply may be interrupted.
· Check if the auto-off function is activated in the settings menu. · If there
is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
Abnormal Display
· If the TV feels cold to the touch, there may be a small flicker when it is
turned on. This is normal; there is nothing wrong with TV. Some minute dot
defects may be visible on the screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on the TV’s performance. Avoid
touching the LCD screen or holding your finger(s) against it for long periods
of time. Doing so may produce some temporary distortion effects on the screen.
· This panel is an advanced product that contains millions of pixels. In a
very few cases, you could see fine dots on the screen while you’re viewing the
TV. Those dots are deactivated pixels and do not affect the performance and
reliability of the TV.
· Displaying a still image for a prolonged period of time may cause an image
sticking. Avoid displaying a fixed image on the TV screen for a extended
length of time.
12
ENGLISH
Generated Sound · Cracking noise A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due to
temperature and humidity. This noise is common for products where thermal
deformation is required. · Electrical circuit humming/panel buzzing A low
level noise is generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending upon the
product. This generated sound does not affect the performance and reliability
of the product.
· When cleaning the product, be careful not to allow any liquid or foreign
objects to enter the gap between the upper, left or right side of the panel
and the guide panel, (Depending upon model).
· Make sure to wring any excess water or cleaner from the cloth.
· Do not spray water or cleaner directly onto the TV screen. · Make sure to
spray just enough of water or cleaner onto a
dry cloth to wipe the screen.
13
ENGLISH
Specifications
Product specifications may be changed without prior notice due to upgrade of product functions. Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only). The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).
(Depending upon country)
Television system Program coverage
(Band) External antenna
impedance
Broadcasting Specifications ATSC, NTSC-M, 64 & 256 QAM
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135
75
(Except for LK61, UK620, UK627*)
Wireless module (LGSBWAC72) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
Output Power (Max.)
2400 to 2483.5 MHz 5150 to 5725 MHz 5725 to 5850 MHz
15 dBm 14.5 dBm 14.5 dBm
Bluetooth
Frequency Range
Output Power (Max.)
2400 to 2483.5 MHz
8.5 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body. FCC ID: BEJLGSBWAC72 IC: 2703H-LGSBWAC72
14
ENGLISH
(Only LK61*)
Wireless module (LGSWFAC81) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
Output Power (Max.)
2400 to 2483.5 MHz 5150 to 5725 MHz 5725 to 5850 MHz
20 dBm 15 dBm 14.5 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body. FCC ID: BEJLGSWFAC81 IC: 2703H-LGSWFAC81
(Only UK620, UK627)
Wireless module(LGSWFAC71) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
Output Power (Max.)
2400 to 2483.5 MHz 5150 to 5725 MHz 5725 to 5850 MHz
15 dBm 14.5 dBm 14.5 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body. FCC ID: BEJLGSWFAC71 IC: 2703H-LGSWFAC71
Operating Temperature Operating Humidity Storage Temperature Storage Humidity
Environment condition 0 °C to 40 °C (32 °F to 104 °F) Less than 80 % -20 °C to 60 °C (-4 °F to 140 °F) Less than 85 %
15
ENGLISH
Open Source Software Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http://
opensource.lge.com. In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a
charge covering the cost of performing such distribution (such as the cost of
media, shipping, and handling) upon email request to opensource@lge.com. This
offer is valid for a period of three years after our last shipment of this
product. This offer is valid to anyone in receipt of this information.
Licenses
Supported licenses may differ by model.
Regulatory
FCC NOTICE
(For USA)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna. – Increase the separation
between the equipment and the receiver. – Connect the equipment to an outlet
on a circuit different from that
to which the receiver is connected. – Consult the dealer or an experienced
radio/TV technician for help. This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Any changes or modifications in construction of this device which
are not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC Radio Frequency Interference Requirements (for UNII devices)
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and
5.65 to 5.85 GHz bands. These radar stations can cause interference with
and/or damage this device. This device cannot be co-located with any other
transmitter.
16
ENGLISH
FCC RF Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,…)] This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be colocated or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with minimum distance 20 cm (7.8 inches) between the radiator and your body.
Users must follow the specific operating instructions for satisfying RF
exposure compliance.
Industry Canada Statement
(For Canada) [For having wireless function (WLAN, Bluetooth,…)] This device
complies with Industry Canada’s applicable licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
(For Canada) [For having wireless function (WLAN, Bluetooth,…)] This equipment
complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum
distance 20 cm (7.8 inches) between the antenna & your body. NOTE : THE
MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
RSS-247 Requirement
(For Canada) [For product having the wireless function using 5 GHz frequency
bands] · The device for operation in the band 51505250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems;
· For devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit;
· For devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate; and
· [For devices operating in the band 5250-5350 MHz having an e.i.r.p. greater
than 200 mW] Antenna type(s), antenna models(s), and worst-case tilt angle(s)
necessary to remain compliant with the e.i.r.p. elevation mask requirement set
forth in section 6.2.2.3 of RSS-247 shall be clearly indicated.
Users should also be advised that high-power radars are allocated as primary
users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and
that these radars could cause interference and/or damage to LE-LAN devices.
NOTE TO CABLE/TV INSTALLER
(For USA and Canada)
This reminder is provided to call the CATV system installer’s attention to
Article 820-40 of the National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to
the point of the cable entry as practical.
17
ENGLISH
WARNING!
Never place a television set in an unstable location. A television set may
fall, causing serious personal injury or death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
· Using cabinets or stands recommended by the manufacturer of the television
set.
· Only using furniture that can safely support the television set. · Ensuring
the television set is not overhanging the edge of the
supporting furniture. · Not placing the television set on tall furniture (for
example,
cupboards or bookcases) without anchoring both the furniture and the
television set to a suitable support. · Not placing the television set on
cloth or other materials that may be located between the television set and
supporting furniture. · Educating children about the dangers of climbing on
furniture to reach the television set or its controls. If your existing
television set is being retained and relocated, the same considerations as
above should be applied.
Symbols
Refers to alternating current (AC). Refers to direct current (DC).
Refers to class II equipment.
Refers to stand-by.
Refers to “ON” (power).
Refers to dangerous voltage.
18
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY CARES
· Manufacturers, retailers and the rest of the consumer electronics industry
are committed to making home entertainment safe and enjoyable. · As you enjoy
your television, please note that all televisions new and old- must be
supported on proper stands or installed according to the manufacturer’s
recommendations. Televisions that are inappropriately situated on dressers,
bookcases, shelves, desks, speakers, chests, carts, etc., may fall over,
resulting in injury.
TUNE IN TO SAFETY
· ALWAYS follow the manufacturer’s recommendations for the safe installation
of your television. · ALWAYS read and follow all instructions for proper use
of your television. · NEVER allow children to climb on or play on the
television or the furniture on which the television is placed. · NEVER place
the television on furniture that can easily be used as steps, such as a chest
of drawers. · ALWAYS install the television where it cannot be pushed, pulled
over or knocked down. · ALWAYS route cords and cables connected to the
television so that they cannot be tripped over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
· ALWAYS contact your retailer about professional installation if you have any
doubts about your ability to safely mount your television. · ALWAYS use a
mount that has been recommended by the television manufacturer and has a
safety certification by an independent laboratory (such as UL, CSA, ETL). ·
ALWAYS follow all instructions supplied by the television and mount
manufacturers. · ALWAYS make sure that the wall or ceiling where you are
mounting the television is appropriate. Some mounts are not designed to be
mounted to walls and ceilings with steel studs or cinder block construction.
If you are unsure, contact a professional installer. · Televisions can be
heavy. A minimum of two people is required for a wall or ceiling mount
installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME
· Many new television buyers move their older CRT televisions into a secondary
room after the purchase of a flat-panel television. Special care should be
made in the placement of older CRT televisions. · ALWAYS place your older CRT
television on furniture that is sturdy and appropriate for its size and
weight. · NEVER place your older CRT television on a dresser where children
may be tempted to use the drawers to climb. · ALWAYS make sure your older CRT
television does not hang over the edge of your furniture.
CE.org/safety
Declaration of Conformity Trade Name: LG Responsible Party: LG Electronics
Inc. Address: 1000 Sylvan Ave. Englewood Cliffs NJ 07632
U.S.A TEL: 201-266-2534
The model and serial numbers of the TV are located on the back and on one side
of the TV. Record them below should you ever need service. MODEL Serial NO.
LG Customer Information Center For inquires or comments, visit www.lg.com or call;
1-800-243-0000 1-888-865-3026 1-888-542-2623
USA, Consumer User USA, Commercial User CANADA
Register your product Online! www.lg.com
OWNER’S MANUAL
EXTERNAL CONTROL DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
ENEGNLGISH
2 KEY CODES
KEY CODES
· This feature is not available for all models.
Code (Hexa)
Function
00 CH +, PR +
01 CH -, PR –
02 Volume +
03 Volume –
06 > (Arrow Key / Right Key)
07 < (Arrow Key / Left Key)
08 Power
09 Mute
0B Input
0E SLEEP
0F TV, TV/RAD
10 – 19 * Number Key 0 – 9
1A Q.View / Flashback
1E FAV (Favorite Channel)
20 Text (Teletext)
21 T. Opt (Teletext Option)
28 Return (BACK)
30 AV (Audio / Video) Mode
39 Caption/Subtitle
40 (Arrow Key / Cursor Up)
41
V (Arrow Key / Cursor Down)
42 My Apps
43 Menu / Settings
44 OK / Enter
45 Q.Menu
4C List, – (ATSC Only)
4D PICTURE
52 SOUND
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
Code (Hexa)
Function
53 List
5B Exit
60 PIP(AD)
61 Blue
63 Yellow
71 Green
72 Red
79 Ratio / Aspect Ratio
91 AD (Audio Description)
9E LIVE MENU
7A User Guide
7C Smart / Home
7E SIMPLINK
8E (Forward)
8F (Rewind)
AA Info
AB Program Guide
B0 (Play)
B1 (Stop / File List)
B5 RECENT
BA
(Freeze / Slow Play / Pause)
BB Soccer
BD (REC)
DC 3D
99 AutoConfig
9F App / *
9B TV / PC
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
- Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea, Japan, North America, Latin America except Colombia models)
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 3
EXTERNAL CONTROL DEVICE SETUP
· Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control
device (such as a computer or an A/V control system) to control the product’s
functions externally.
Note: The type of control port on the TV can be different between model
series.
- Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB to Serial converter with USB Cable
USB Type
USB IN
(PC)
(TV)
· LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008)
USB to serial converter which is not made nor provided by LG.
· It can be purchased from computer stores that carry accessories for IT
support professionals.
RS-232C With RS232C Cable
DE9 (D-Sub 9pin) Type · You need to purchase the RS-232C (DE9, D-Sub 9pin
female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the
manual.
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
The connection interface may differ from your TV.
ENEGNLGISH
4 EXTERNAL CONTROL DEVICE SETUP
Phone jack Type
· You need to purchase the phone-jack to RS-232 cable required for the
connection between the PC and the TV, which is specified in the manual.
- For other models, connect to the USB port. * The connection interface may differ from your TV.
SERVICE ONLY
1 3
(PC)
(TV)
2
– or
(PC)
31 2
RS-232C IN
(CONTROL & SERVICE)
(TV)
Customer Computer
1
5
RS-232C configurations
3-Wire Configurations(Not standard)
RXD
PC 2
TV 2 TXD
TXD 3 GND 5
1 RXD 3 GND
6
9
RS-232C (Serial port)
RXD TXD GND
OR 3 2 5
D-Sub 9
2 1 3 Phone
TXD RXD GND
Set ID For Set ID number, see “Real Data Mapping” on p.6
1. Press SETTINGS to access the main menus. 2. Press the Navigation buttons to scroll to (*General About this TV or OPTION) and press OK. 3. Press the Navigation buttons to scroll to SET ID and press OK. 4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99. 5. When you are finished, press EXIT.
- (Depending on model)
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 5
Communication Parameters
· Baud rate : 9600 bps (UART) · Data length : 8 bits · Parity : None
Command reference list
(Depending on model)
· Stop bit : 1 bit · Communication code : ASCII code · Use a crossed (reverse) cable.
COMMAND1
COMMAND2
DATA (Hexadecimal)
COMMAND1
COMMAND2
DATA (Hexadecimal)
01. Power* k
02. Aspect Ratio
k
03. Screen Mute
k
04. Volume Mute
k
05. Volume Control
k
06. Contrast k
07. Brightness
k
08. Color/ Colour
k
09. Tint
k
10. Sharpness
k
11. OSD Select
k
12. Remote Control Lock k Mode
13. Treble k
a
00 to 01
15. Balance k
t
16. Color
c
(p.7)
(Colour)
x
u
Temperature
17. ISM
d
(p.7)
Method (Only j
p
Plasma TV)
e
00 to 01
18. Equalizer j
v
f
00 to 64
19. Energy Saving
j
q
g
00 to 64
20. Tune Command
m
a
21. Channel m
b
h
00 to 64
(Programme)
Add/Del(Skip)
i
00 to 64
22. Key
m
c
23. Control m
g
j
00 to 64
Backlight, Control Panel
Light
k
00 to 32
24. Input
x
select (Main)
b
l
00 to 01
25. 3D (Only x 3D models)
t
26. Extended x
v
m
00 to 01
3D (Only 3D
models)
27. Auto
j
u
r
00 to 64
Configure
00 to 64 00 to 64
(p.8) (p.8) 00 to 05 (p.9) 00 to 01
Key Codes 00 to 64
(p.11) (p.11) (p.12)
(p.12)
14. Bass
k
s
00 to 64
- Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. With RS232C cable, TV can communicate “ka command” in power-on or power-off status. but with USB-to-Serial converter cable, the command works only if TV is on.
ENEGNLGISH
6 EXTERNAL CONTROL DEVICE SETUP
Transmission / Receiving Protocol
Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV. [Set ID]
: You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to `0′, every connected set
can be controlled.
- [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA]
: To transmit command data (hexadecimal). Transmit `FF’ data to read status of command.
[Cr]
: Carriage Return – ASCII code `0x0D’
[ ]
: Space ASCII code `0x20′
OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set
transmits ACK (acknowledgement) based on this format when receiving abnormal
data from non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
- When you enter the [data] in hexadecimal, refer to following conversion table. * Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 01 : Step 1 (Set ID 1) … 0A : Step 10 (Set ID 10) … 0F : Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) …
32 : Step 50 (Set ID 50) 33 : Step 51 (Set ID 51) … 63 : Step 99 (Set ID 99) … C7 : Step 199 C8 : Step 200 …
FE : Step 254 FF : Step 255 … 01 00 : Step 256 … 27 0E : Step 9998 27 0F : Step 9999 …
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 7
- Commands may work differently depending on model and signal.
01. Power (Command: k a) To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x] To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x]
- Similarly, if other functions transmit `FF’ data based on this format, Acknowledgement feedback presents status about each function.
Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will
display On Screen Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
04. Volume Mute (Command: k e) To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control. Transmission
[k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x]
02. Aspect Ratio (Command: k c) (Main Picture Size)
To adjust the screen format. (Main picture format) You can also adjust the
screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Mid-
except Colombia East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Original
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
- Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
- In DTV/HDMI/Component mode (high-definition), Just Scan is available.
- Full wide mode may work differently based on model and is supported for DTV fully, and ATV, AV partially.
03. Screen Mute (Command: k d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture
on) Video mute off
01 : Screen mute on (Picture off) 10 : Video mute on
05. Volume Control (Command: k f) To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [f][
][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) To adjust screen
contrast.
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [g][ ][Set ID][
][OK/NG][Data][x] 07. Brightness (Command: k h) To adjust screen brightness.
You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [h][ ][Set ID][
][OK/NG][Data][x]
ENEGNLGISH
8 EXTERNAL CONTROL DEVICE SETUP
08. Color/Colour (Command: k i) To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [i][ ][Set ID][
][OK/NG][Data][x] 09. Tint (Command: k j) To adjust the screen tint.
You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][
][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k) To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l) To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m) To lock the front panel controls
on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
- If you are not using the remote control, use this mode. When main power is off & on (plug-off and plug-in, after 20 – 30 seconds), external control lock is released.
- In the standby mode (DC off by off timer or
ka’,
mc’ command), and if key lock is on, TV will not turn on by power on key of IR & Local Key.
13. Treble (Command: k r) To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
14. Bass (Command: k s) To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
15. Balance (Command: k t) To adjust balance.
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u) To adjust colour temperature.
You can also adjust
Color(Colour) Temperature in the PICTURE menu. Transmission [x][u][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV) To control the ISM method. You
can also adjust
ISM Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data
Min : 02: Orbiter
08: Normal 20: Color(Colour) Wash Ack [p][ ][Set ID][ ][OK/NG][Data][x]
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 9
18. Equalizer (Command : j v)
Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
LSB
0000000 0
Frequency
Data
7 6 5 Frequency 4 3 2 1 0
Step
0 0 0 1st Band 0 0 0 0 0 0(decimal)
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
0 1 0 3rd Band … … … … …
…
0 1 1 4th Band 1 0 0 1 1 19(decimal)
1 0 0 5th Band 1 0 1 0 1 20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
- It depends on model, and can adjust when sound mode is EQ adjustable value.
19. Energy Saving (Command: j q)
To reduce the power consumption of the TV. You can also adjust Energy Saving
in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 00 : Off 01 : Minimum 02 :
Medium 03 : Maximum 04 : Auto (For LCD TV / LED TV) / Intelligent sensor (For
PDP TV) 05 : Screen off
- (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Tune Command (Command: m a)
-
This command may work differently depending on model and signal.
· For Europe, Mid-East, Colombia, Asia except South Korea and Japan Model
Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ] [Data 01][ ][Data 02][Cr] -
Analog Antenna/Cable
[Data 00][Data 01] Channel Data Data 00 : High byte channel data Data 01 : Low byte channel data
– 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog) – 00 : Antenna TV (ATV) – 80 : Cable TV (CATV) -
Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data
– 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 02 : Input Source (Digital)
– 10 : Antenna TV (DTV) – 20 : Antenna Radio (Radio) – 40 : Satellite TV (SDTV) – 50 : Satellite Radio (S-Radio) – 90 : Cable TV (CADTV) – a0 : Cable Radio (CA-Radio) -
Tune Command Examples: 1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00 Data 00 & 01 = Channel Data is 10 = 00 0a Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01. Set ID = All = 00 Data 00 & 01 = Channel Data is 1 = 00 01 Data 02 = Digital Antenna TV = 10 Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000 = 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x] · For South Korea, North/Latin America except Colombia Model
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major / Minor number, the Physical number is not required when sending a command in Digital.
ENEGNLGISH
10 EXTERNAL CONTROL DEVICE SETUP
- Analog Antenna/Cable
Data 00 : Physical Channel Number – Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) – Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Don’t care) Data 03 & 04: xx (Don’t care) Data 05: Input Source (Analog)
– 00 : Antenna TV (ATV) – 01 : Cable TV (CATV) - Digital Antenna/Cable
Data 00 : xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital) – 02 : Antenna TV (DTV) Use Physical Channel Number – 06 : Cable TV (CADTV) Use Physical Channel Number – 22 : Antenna TV (DTV) Don’t Use Physical Channel Number – 26 : Cable TV (CADTV) – Don’t Use Physical Channel Number – 46 : Cable TV (CADTV) Use Physical/Major Channel Number Only (One Part Channel) – 66 : Cable TV (CADTV) Use Major Channel Number Only (One Part Channel) – 0b : Cable DTV Plus Use Physical Channel Number – 2b : Cable DTV Plus Don’t Use Physical Channel Number – 4b : Cable DTV Plus Use Physical/Major Channel Number Only (One Part Channel) – 6b : Cable DTV Plus Use Major Channel Number Only (One Part Channel)
Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). - Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00 Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analog Cable TV = 01 Total = ma 00 23 00 00 00 00 01
2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00
= Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 =
Minor is 3 = 00 03 Data 05 = Digital Antenna TV = 22 Total = ma 00 00 00 1E 00
03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data
05] [x][a][ ][Set ID][ ][NG][Data 00][x] · For Japan Model To tune channel to
following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][
][Data04][ ][Data05][Cr] * Digital Antenna/Satellite Data 00: xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data
02: Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite)
Data 03: High byte Channel Data Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan) – 02 : Antenna TV (DTV) –
42 : Antenna TV (DTV) Use Physical/Major Channel Number Only (One Part
Channel) – 62 : Antenna TV (DTV) Use Major Channel Number Only (One Part
Channel) – 07 : BS (Broadcasting Satellite) – 08 : CS1 (Communication
Satellite 1) – 09 : CS2 (Communication Satellite 2)
- Tune Command Examples: 1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 = 00 01 Data 05 = Digital Antenna TV = 02 Total = ma 00 00 00 11 00 01 02
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 11
2. Tune to the BS (ISDB-BS) channel 30. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Don’t Care = 00 00 Data 05 = Digital BS TV = 07 Total = ma 00 00 00 1E 00 00 07
- This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 21. Channel(Programme) Add/Del(Skip) (Command: m b)
To skip current channel(programme) for next time. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Set the saved channel status to del(ATSC, ISDB)/ skip(DVB) or add.
22. Key (Command: m c) To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code – p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Control Backlight (Command: m g) · For LCD TV / LED TV To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x] Control Panel Light (Command: m g)
· For Plasma TV To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b) (Main Picture Input)
To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
20 : AV or AV1
21 : AV2
40 : Component1 60 : RGB
41 : Component2
90 : HDMI1 92 : HDMI3
91 : HDMI2 93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
- This function depends on model and signal.
25. 3D(Command: x t) (only 3D models) (Depending on model)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [ ][Data 02][ ][Data
03][Cr] (Depending on model) Data Structure [Data 00] 00 : 3D On
01 : 3D Off 02 : 3D to 2D 03 : 2D to 3D [Data 01] 00 : Top and Bottom 01 :
Side by Side 02 : Check Board 03 : Frame Sequential 04 : Column interleaving
05 : Row interleaving [Data 02] 00 : Right to Left 01 : Left to Right [Data
03] 3D Effect(3D Depth): Min : 00 – Max : 14 (transmit by Hexadecimal code)
ENEGNLGISH
12 EXTERNAL CONTROL DEVICE SETUP
- [Data 02], [Data 03] functions depend on model and signal.
- If [Data 00] is 00 (3D On), [Data 03] has no meaning.
- If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 01], [Data 02] and [Data 03] have no meaning.
- If [Data 00] is 03 (2D to 3D), [Data 01] and [Data 02] have no meaning.
- If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 03] works when 3D Mode (Genre) is manual only.
- All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.
[Data 00] 00 [Data 01] O
01
X
02
X
03
X
X : don’t care
[Data 02] O X X O [Data 03] O X X O
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] [Data03][x] [t][ ][Set ID][ ][NG][Data00][x]
26. Extended 3D(Command: x v) (only 3D models) (Depending on model)
To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ] [Data 01][Cr] [Data 00] 3D
option 00 : 3D Picture Correction 01 : 3D Depth (3D Mode is Manual Only) 02 :
3D Viewpoint 06 : 3D Color Correction 07 : 3D Sound Zooming 08 : Normal Image
View 09 : 3D Mode (Genre)
[Data 01] It has own range for each 3D option determined by [Data 00].
-
When [Data 00] is 00 00 : Right to Left 01 : Left to Right
-
When [Data 00] is 01, 02 Data Min: 0 – Max: 14 (transmit by Hexadecimal
code) Data value range(0 – 20) converts Viewpoint range (-10 – +10) automatically (Depending on model) This option works when 3D Mode (Genre) is manual
only. -
When [Data 00] is 06, 07 00 : Off 01 : On
-
When [Data 00] is 08 00 : Revert to 3D video from 3D-to-2D converted 2D video 01 : Change 3D video to 2D video, except 2D-to-3D video
- If conversion condition doesn’t meet, command is treated as NG.
- When [Data 00] is 09
00 : Standard 02 : Cinema 04 : Manual
01 : Sport 03 : Extreme 05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x] [v][ ][Set ID][ ][NG][Data00][x]
27. Auto Configure (Command: j u) (Depending on model)
To adjust picture position and minimize image shaking automatically. It works
only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
SMART TV Quick Setup Guide
- Image shown may differ from your TV. Image shown on a PC or mobile phone may vary depending on the OS(Operating System). App icon positions may vary on the platform, depending upon the software version.
Network Settings
1 Press the (Home) button on the remote to access the Home menu. Point the (Settings) icon and select by pressing the Wheel (OK) button on the remote.
WI-FI CONNECTION
Picture Network /
Sound
Channels
Network
General Safety Accessibility
Add a Hidden Wireless Network Connect via WPS PBC Connect via WPS PIN
Advanced Wi-Fi Settings
2 Point the ( ) (All Settings) icon and select by pressing the Wheel (OK) button on the remote.
All Settings
()
For wireless AP (Router) that have the symbol, you need to enter the security
key.
5 If the connection is successful, the “Connected to Internet” is displayed.
NETWORK
Picture
Sound Channels Network General
TV Name
Wired Connection (Ethernet) Not Connected Wi-Fi Connection Connected to
Internet Wi-Fi Direct
Safety
Accessibility
3 Select the Network Wired Connection (Ethernet) or Wi-Fi Connection.
You can check the status of connection in Advanced Wi-Fi settings.
NETWORK
Picture
Sound Channels Network General
TV Name
Wired Connection (Ethernet) Not Connected Wi-Fi Connection Not Connected Wi-Fi
Direct
Safety
Accessibility
4 The device automatically tries to connect to the network available (wired network first). When you select the Wi-Fi Connection, the network list available is displayed. Choose the network you wish to use.
WI-FI CONNECTION
Picture Network /
Sound
Channels
Network
General Safety Accessibility
Add a Hidden Wireless Network Connect via WPS PBC Connect via WPS PIN Advanced Wi-Fi Settings
www.lg.com
Troubleshooting Network Problems
1 Press the (Home) button on the remote to access the Home menu. Point the (Settings) icon and select by pressing the Wheel (OK) button on the remote.
Follow the instructions below that match to your network status.
Check the TV or the AP (Router).
2 Point the ( ) (All Settings) icon and select by pressing the Wheel (OK) button on the remote.
When X appears next to TV:
1 Check the connection status of the TV, AP (Router) and cable modem.
2 Power off and power on in the following order; (1st) the cable modem, wait
for the cable modem to reset, (2nd) the AP (Router), wait for the AP (Router)
to reset and (3rd) the TV.
3 If you are using a static IP, enter the IP directly. 4 Contact internet
service provider or AP (Router)
manufacturer.
Check the AP (Router) or consult your Internet service provider.
All Settings
()
3 Select the Network Wired Connection (Ethernet) or Wi-Fi Connection Advanced Wi-Fi Settings.
NETWORK
Picture
Sound Channels Network
General
TV Name
Wired Connection (Ethernet) Not Connected Wi-Fi Connection Not Connected Wi-Fi
Direct
Safety
Accessibility
WI-FI CONNECTION
Picture Network /
Sound
Channels Network
General Safety Accessibility
Add a Hidden Wireless Network Connect via WPS PBC Connect via WPS PIN Advanced Wi-Fi Settings
When X appears next to Gateway: 1 Unplug the power cord of the AP (Router) or
cable modem, wait 5 seconds. Reapply power. 2 Initialize (Reset) the AP
(Router) or cable
modem. 3 Contact Internet service provider or AP (Router)
manufacturer.
When X appears next to DNS: 1 Unplug the power cord of the AP (Router) or
cable modem, wait 5 seconds. Reapply power. 2 After the cable modem or AP
(Router) has
initialized (Reset), try to reconnect. 3 Check that the MAC address of the
TV/AP
(Router) is registered with your Internet service provider. (The MAC address
displayed on the right pane of the network status window should be registered
with your Internet service provider.) 4 Check the AP (Router) manufacturer’s
website to make sure your router has the latest firmware version installed.
SmartShare PC SW Installing & Setting
1 Install the SmartShare PC SW programme on your PC.
2 Go to
. Then, select your region.
3 Select Support.
4 Select Software & Drivers. Then, select SmartShare.
5 Download the SmartShare PC SW and install it on your PC. You can run the program when installation is complete.
NOTE
y Smartshare service is only available if TV and other devices are connected
via a single AP (Router).
SmartShare Connection to Smartphone
1 Check that Wi-Fi is enabled on your smartphone. To use SmartShare, both
devices must on the same local network.
2 Install/run the app for sharing content on your smartphone (It’s called LG
TV Plus on LG phones).
3 Enable your smartphone to share content files with other devices. 4 Open
Device Connector application.
(Home) Device Connector Smartphone CONTENT SHARE. 5 Select the file type you
want to play (movie, audio or photo).
6 Select a movie, music or photo file to play on the TV.
7 Play the media file to view and enjoy it on your TV.
Updating the TV Firmware
- If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.
1 (Home) (Settings) ( ) (All Settings) General About This TV CHECK FOR UPDATES
2 After checking the version of the software, update it. If you check the “Allow Automatic Updates”, you can update the software automatically.
GENERAL
Picture
Sound Channels
Eco Mode Mobile TV On
Network LG Wireless Keyboard
General Safety
Settings Help No Signal Image Reset to Initial Settings
About This TV Accessibility
User Agreements
ABOUT THIS TV
Picture General /
Sound Channels Network
General
Safety
Accessibility
Software Version
xx.xx.xx
Allow Automatic Updates
CHECK FOR UPDATES
TV Information User Guide Open Source Software Notice Set ID : 1
Wi-Fi Direct Setting
WI-FI Direct
Picture Network /
REFRESH LIST
Sound
Channels
(Home) (Settings) ( ) (All Settings) Network Wi-Fi Direct
If a local network is not available, you can connect a portable device directly to the TV
using Wi-Fi Direct.
With
, you can share files or screens of devices connected to Wi-Fi Direct.
Network
1 When you open Wi-Fi Direct menu, a list of available devices appears.
General
Safety Accessibility
2 When you are prompted to request connection, select Yes. Wi-Fi Direct is now connected to your TV.
- You can only use devices that support Wi-Fi Direct.
Miracast Setting
Miracast allows a portable device to send video and sound securely to the TV
wirelessly. 1 Miracast should be set to “ON” on your portable device.
2 When your TV is detected, select the device on your portable device. When
connection is completed, the device screen appears on the TV screen.
Please call LG Customer Service if you experience any problems.
ENGLISH
Easy Setup Guide Please read this manual carefully before operating your set and retain it for future reference.
MFL70343402
www.lg.com
ESPAÑOL Guía Rápida de Configuración Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.
(1801-REV00) Printed in Korea
43UK6300PUE 43UK6300BUB 49UK6300PUE 49UK6300BUB 50UK6300PUE
55UK6300PUE 55UK6300BUB 65UK6300PUE 65UK6300BUB
FRANÇAIS Guide de configuration rapide Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour pouvoir vous y reporter ultérieurement.
43UK63*
1
2
3
4
50UK6300BUB
B
a
AAA
B
A
B
A
a
b
5
X 2
X 4
X6
(M4 X L16) (M4 X L16) 43UK63 49/50/55UK63
(M4 X L20) 65UK63*
43UK63*
49/50/55/65UK63*
ENGLISH Read Safety & Reference. ESPAÑOL Leer Seguridad y Consultas. FRANÇAIS Lisez Sécurité et références.
49/50/55/65UK63*
1
2
3 49/50/55/65UK63*
BB
B
BB
AA
BB
B
A
B
A
4-A 49/50/55UK63*
4-B 65UK63*
5
6
(For USA and Canada only) (Para Estados Unidos y Canadá)
This product qualifies for ENERGY STAR® in the factory default (Home
configuration) setting. Changing the factory default settings or enabling
other features may increase power consumption that could exceed the limits
necessary to quality for ENERGY STAR®. Refer to ENERGYSTAR.gov for more
information on the ENERGY STAR® program.
(Pour les États-Unis et le Canada) Ce produit est conforme aux normes ENERGY
STAR® lorsque le réglage d’usine par défaut (Résidentiel) est sélectionné.
Modifier les réglages
d’usine par défaut ou activer d’autres fonctionnalités augmente la
consommation d’énergie qui pourrait alors dépasser les limites de la
qualification ENERGY STAR®. Consultez le site ENERGYSTAR.gov pour en savoir
plus au sujet du programme ENERGY STAR®.
B
a
B A
B
b
B A
: Depending upon model / Según el modelo / Selon le modèle
B A
www.lg.com/us/support
ENGLISH Easy TV Connect Guide (Animation) ESPAÑOL Guía Rápida de Conexión del
televisor (Sólo en Inglés) FRANÇAIS Guide simplifié pour la connexion du
téléviseur (Offert en anglais seulement)
VIDEO/Y PB PR L/MONO AUDIO R VIDEO/Y PB PR L/MONO AUDIO R
VIDEO L/MONO AUDIO R
VIDEO
AUDIO
0 12
A E
D
B
G C
F
, , , , ,
: mm (inches / pulgadas / po) : kg (lbs / libras / lb)
A
B
C
D
E
F
F G
43UK6300PUE 977 977 629 629 216 216 575 575 80.8 43UK6300BUB (38.4) (38,4)
(24.7) (24,7) (8.5) (8,5) (22.6) (22,6) (3.1) 49UK6300PUE 1,110 1 110 709 709
231 231 650 650 81.1 49UK6300BUB (43.7) (43,7) (27.9) (27,9) (9) (9) (25.5)
(25,5) (3.1) 50UK6300PUE 1,133 1 133 723 723 231 231 663 663 87.9 50UK6300BUB
(44.6) (44,6) (28.4) (28,4) (9) (9) (26.1) (26,1) (3.4) 55UK6300PUE 1,247 1
247 785 785 231 231 729 729 88.6 55UK6300BUB (49) (49) (30.9) (30,9) (9) (9)
(28.7) (28,7) (3.4) 65UK6300PUE 1,468 1 468 917 917 269 269 854 854 89.9
65UK6300BUB (57.7) (57,7) (36.1) (36,1) (10.5) (10,5) (33.6) (33,6) (3.5)
Power requirement / Alimentación requerida / Alimentation
80,8 8.4 8,4 8.3 8,3 (3,1) (18.5) (18,5) (18.2) (18,2) 81,1 11.3 11,3 11.1
11,1 (3,1) (24.9) (24,9) (24.4) (24,4) 87,9 10.8 10,8 10.6 10,6 (3,4) (23.8)
(23,8) (23.3) (23,3) 88,6 13.9 13,9 13.7 13,7 (3,4) (30.6) (30,6) (30.2)
(30,2) 89,9 21 21 20.6 20,6 (3,5) (46.2) (46,2) (45.4) (45,4)
AC 100-240 V ~ 50 / 60 Hz
95 W 120 W 130 W 135 W 190 W
References
- Homepage | ENERGY STAR
- Manual-Hub.com - Free PDF manuals!
- LG Open Source
- LG Electronics & Home Appliances | Shop Now | LG USA
- Arbitration | LG USA
- Get Product Help & Support | LG USA Support
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>