Liehuzhekeji 702248611559 Backup Camera and 7 Inch LCD Monitor Kit User Manual
- June 15, 2024
- Liehuzhekeji
Table of Contents
Liehuzhekeji 702248611559 Backup Camera and 7 Inch LCD Monitor Kit
Specifications
- 7-inch LCD Monitor
- Camera included
- Power Cord included
- Mounting Bracket included
- 10M Cable included
- Two-sided Adhesive Tap included
- Remote Control included (Requires a CR2025 button battery, not included)
DURING THE WARRANTY PERIOD, SHOULD YOUR REAR VIEW PRODUCT EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP, PLEASE CONTACT US FOR REPLACEMENT.
The Protective Film
There is a protective film on the screen, which protects the screen during
shipping. If it is scratched, you can replace one before using.
Tear off The Film
The film can be teared it off by the small white tape on the corner.
If it is stuck, please use your nail to make a small gap between the frame and
the screen, then use another hand to tear the film off.
Press these two buttons at the same time to take out the monitor, align the round holes under the display and tighten the screws.
The display screen can be adjusted up and down, left and right at will, which is very flexible and practical.
What you get
- 1* 7-inch Monitor
- 1* Camera
- 1* Power Cord
- 1* Mounting Bracket
- 1* 10M Cable
- 1 x Two-sided Adhesive Tap
- 1* Remote Control(Require a CR2025 button battery, not include) 1 x User Manual
Wiring
The package includes one camera and one 10-meter cable. The installation is very easy, please reference the below wiring diagram.
Tips:
- The connector is pins type, please be careful to connect it correctly and tightly. Every connector has an interface mark.
- If you have any confusion or problems after installation, please contact us first, and we will try our best to serve you.
Remote Control
- Power: turn on/off monitor
- Video: V1/V2 selecting
- Down selection
- Menu
- Mode—– Mode election
- Up selection
Menu Settings- —-Switch Cameras/Reset/Guideline/brightness/contrast./Image flip
Switch Cameras
Press button “V1/V2” to switch cameras to AHD1/AHD2
Reset
Press the button“MENU”, press the button “+” and press button “V1/V2” or to
select ”SYS” icon, press button “+” or “-” to choose “RESET”
Guide line
Press the button“MENU”, press the button “+” and press the button “V1/V2” or to select the”CAR” icon, press the button “+” or “-” to turn the on/off guideline. ROTATE 1 for camera 1, ROTATE 2 for camera 2.
You also can adjust the width and height of the reversing line. When the guide line is set, there will be letter “H” or “W” on the left side of the guide line, press the button“MENU” menu to switch “H” and “W”, hold and press the button “+” or “-” to adjust the guide line width and height.
Brightness/contrast.
Press the button“MENU”, and press the button “V1/V2” or to select the”PIC”
icon, press button “+” or “-” to choose set brightness/contrast.
Image flip
Press the second button to rotate the image, the image can be switched from four modes of normal facing/rear view/mirror upside down/upside down facing.
Troubleshooting
Camera not work
- Please check if the extension cable and connector are good or not.
- Wrong input settings, please switch V1/V2.
If still does not work, please contact us for a free replacement.
The monitor not turn on
a. After connecting to power DC 12V-35V, is the screen black or blue?
-
If the screen is black, the screen can’t be powered
Please check if the fuse or power connection is good, and if the power voltage is constant DC 12V-35V. -
You can also do a test, remove the screen from the car, and connect the screen directly to a battery, red positive and black negative. See if it can turn on.
-
If the screen is blue, showing the character ‘AHD1/AHD2”, the screen is good.
b. You can test cameras with another monitor.
If still does not work, please contact us for a free replacement.
Remote not work
- Please put a CR2025 button battery in the remote, the battery is not included.
- When using the remote control, it needs to be aimed at the monitor.
If still does not work, please contact us for a free replacement.