amazon basics B08291MFPB Wall Mounted Recessed Electric Fireplace Instruction Manual

amazon basics B08291MFPB Wall Mounted Recessed Electric Fireplace

TOOLS

WHAT IN THE BOX

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following

WARNING Risk of fire

• In order to avoid overheating, do not cover the heater Do not place objects in contact with the heater
• The appliance must not be used if the glass panel is damaged

CAUTION Risk of burns!
Some parts of this product can become very hot and cause burns Particular attention has to be given where children and vulnerable people are present

• Read all instructions before using this heater
• This heater is hot when in use To avoid burns, do not let bare skin touch hot surfaces If provided, use handles when moving this heater Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (2 meter) from the front of the heater and keep away from the sides and rear
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended
• Do not operate any heater with a damaged cord or plug after the heater malfunctions, has been dropped, or is damaged in any manner Discard the heater or return it to an authorized service facility for examination and/or repair
• Do not use outdoors
• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations Never locate the heater where it may fall into a bathtub or other water container
• Connect to properly grounded outlets only
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater
• To prevent a possible fire, do not block air intakes or exhaust in any manner Do not use on soft surfaces, like a bed, where openings may become blocked
• A heater has hot and arcing or sparking parts inside Do not use it in areas where gasoline, paint or flammable liquids are used or stored
• Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons

For wall installation A:

• Always unplug the appliance when not in use
• To disconnect the heater, turn the controls off, then remove the plug from the outlet
• Do not run the cord under carpeting Do not cover the cord with throw rugs, runners or similar coverings Do not route the cord under furniture or appliances Arrange the cord away from traffic areas and where it will not be tripped over
• Always plug heaters directly into a wall outlet/receptacle Never use with an extension cord or relocatable power tap (outlet/power strip)
• This heater is fitted with a temperature limiting control If the heater reaches an unsafe internal temperature of
  239 °F (115 °C), the product automatically switches off To reset, unplug the product from the socket outlet and wait 5 minutes before plugging it back in and switching on

For recessed installations B and C:

• The socket outlet must be wired to a dedicated and accessible 16 A double pole switch to safely switch the product on/off
• Always set the wall switch to off when not in use
• This heater is fitted with a temperature-limiting control
• If the heater reaches an unsafe internal temperature of 239 °F (115 °C), the product automatically switches off
• To reset, set the wall switch to off and wait 5 minutes before switching back on
• This heater is fitted with a temperature limiting control? If the heater reaches an unsafe internal temperature of 239 °F (115 °C), the product automatically switches off? To reset, set the wall switch to off and wait 5 minutes before switching back on

SAVE THESE INSTRUCTIONS

Battery Warnings

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery
• DEATH or serious injury can occur if ingested
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours
• KEEP new and used batteries OUT OF THE REACH OF CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body
• Immediately dispose of used batteries and keep away from children Do NOT dispose of batteries in household trash
• Even used batteries may cause severe injury or death
• Call a local poison control centre for treatment information

INGESTION HAZARD: This product contains a button cell or coin battery

• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries

• Remove and immediately discard batteries from equipment not used for an extended period

• Non-rechargeable batteries are not to be recharged

• Do not force discharge, recharge, disassemble,
  heat above (manufacturer’s specified temperature rating) or incinerate Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns

• Keep batteries out of the reach of children. In particular, keep batteries that are considered swallowable out of the reach of children. In case of ingestion of a coin cell seek medical assistance promptly.

• Do not allow children to replace batteries without adult supervision.

• Always insert batteries correctly concerning polarity (+ and -) marked on the battery and the equipment. When batteries are inserted in reverse they might be short-circuited or charged. This can cause overheating, leakage, venting, rupture, explosion, fire, and personal injury.

• Do not short-circuit batteries. When the positive (+) and negative (-) terminals of a battery are in electrical contact with each other, the battery becomes short-circuited. For example, loose batteries in a pocket with keys or coins can be short-circuited. This can result in venting, leakage, explosion, fire, and personal injury.

• Do not charge batteries. Attempting to charge a non-rechargeable (primary) battery can cause internal gas and/or heat generation resulting in leakage, venting, explosion, fire and personal injury.

• Do not force discharge batteries. When batteries are force discharged using an external power source the voltage of the battery will be forced below its design capability and gases will be generated inside the battery. This can result in leakage, venting, explosion, fire, and personal injury.

• Exhausted batteries should be immediately removed from equipment and properly disposed of. When discharged batteries are kept in the equipment for a long time electrolyte leakage can occur causing damage to the equipment and/or personal injury.

• Do not heat batteries. When a battery is exposed to heat, leakage, venting, explosion or fire can occur and cause personal injury.

• Do not weld or solder directly to batteries. The heat from welding or soldering directly to a battery can cause leakage, venting, explosion or fire, and can cause personal injury.

• Do not dismantle batteries. When a battery is dismantled or taken apart, contact with the components can be harmful and can cause personal injury or fire.

• Do not deform batteries. Batteries should not be crushed, punctured, or otherwise mutilated. Such abuse can cause leakage, venting, explosion or fire and can cause personal injury.

• Do not dispose of batteries in a fire. When batteries are disposed of in a fire, the heat build-up can cause an explosion and/or fire and personal injury. Do not incinerate batteries except for approved disposal in a controlled incinerator.

• A lithium battery with a damaged container should not be exposed to water. Lithium metal in contact with water can produce hydrogen gas, fire, explosion, and/or cause personal injury.

• Do not encapsulate and/ or modify batteries. Encapsulation of any other modification to a battery can result in blockage of the pressure relief mechanism(s) and subsequent explosion and personal injury. Advice from the battery manufacturer should be sought if it is considered necessary to make any modification.

3. Grounding Instructions

This heater is for use on 120 volts The cord has a plug as shown in Sketch A An adapter as shown at Sketch B is available for connecting three-blade grounding-type plugs to two-slot receptacles The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box as shown at sketch C The adapter should not be used if a three-slot grounded receptacle is available

Intended Use

• This product is suitable for providing instant heat to warm up a room and also for visual ambiance It is not intended for use as a primary heat source

• This product is intended for household use only It is not intended for commercial use
  This product must be wall or recessed mounted IT IS NOT SUITABLE
  FOR USE AS A FREE STANDING APPLIANCE Operating the product in any other position could cause a hazard

• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions

Before First Use

DANGER Risk of suffocation!

• Keep any packaging materials away from children – these materials are a potential source of danger, eg suffocation
• Check the product for transport damages
• remove all packing materials including packaging inside the firebox behind the glass display panel (A) as described in installation B step 1
• Before connecting the product to the power supply, check that the power supply voltage and current rating correspond with the power supply details shown on the product rating label
• Remove the protective strip on the remote control battery compartment

Product Description

• A Display panel
• B Logs
• C Heating vents
• D Display
• E Touch controls
• F On/off switch
• G Power cord with plug
• H Wall mounting bracket
• I Set mounting bracket
• J Ember color button
• K Ember lock button
• L Temperature button
• M Timer button
• N Flame color button
• O Flame lock button
• P Power level button
• Q Standby button

Touch controls

Installation Tips

WARNING

• Failure to install the product as instructed may result in damage to the product and or may expose the user to the risk of fire, electric shock, or serious injury

• This product should be installed and maintained only by an experienced adult If in doubt, consult a professional

• Before mounting, determine the suitable mounting location The product must be fixed to a wooden or masonry/concrete wall using fasteners that are appropriate for the mounting surface

• Do not install on drywalls, wall boards or thin plywood The mounting surface must be capable of supporting the weight of the product

• For best results, install the product out of direct sunlight

• To avoid reconstruction install the product in proximity of the properly grounded socket outlet
  Do not drill into any pipes or power lines beneath the surface during mounting hole preparation Use a voltage/metal detector

• The wall mounting bracket (H) is attached to the product when delivered Remove it before installation

For recessed installation B: The socket outlet must be wired to an accessible 16 A double pole switch to safely switch the product on/off.

Operation

Switching on/off

1. Connect the power cord with plug (G) to a suitable socket outlet.

2. Set the power switch (F) to ‘I’ (product on). The product beeps and U1.2 shows on display (D). The product is now in standby mode.

3. Press the standby button (Q) to switch on the product.
   NOTIC E The display goes off approximately 7 seconds after no other button is pressed

4. To switch off the product, press the standby button (Q) again

NOTICE

• Pressing any button on the remote or touch controls (E) once displays the current room temperature To select any function, press the same button twice
• There may be a trace of odor during the first few minutes of use, or after a period of storage This is normal and quickly disappears
• If the product is not in use for a long period:

For wall installation A: Set the power switch (F) to ‘0’ and remove the plug (G) from the socket outlet
For recessed installation B: Set the wall switch to off

Setting temperature

• Press the temperature button (L) repeatedly until the desired temperature has been selected
• The temperature range is between 62 – 86 °F (17 – 30 °C)
• When the room reaches the set temperature, the heating function stops automatically
• If the product detects a drop in temperature, the heating function resumes automatically

Changing power level
Press the power level button (P) to cycle through the different power settings The display (D) shows the below symbols to indicate the power level selected?

Changing flame color

• Press the flame color button (N) repeatedly until the desired color is selected
• The display (D) shows the code to indicate the color selected
• When using F0 mode, press the flame lock button (O) at anytime to stop the loop Press the flame lock button (O) again to resume

Changing ember color

• Press the ember button (J) repeatedly until the desired color is selected
• The display (D) shows the code to indicate the color selected
• When using C0 mode, press the charcoal lock button (K) at anytime to stop the loop Press the ember lock button (K) again to resume

Setting timer

• Press the timer button (M) repeatedly until the desired time is selected
• Display (D) shows the selected hour for 7 seconds, then displays room temperature The timer automatically starts counting down
• The timer function can be set between 1 – 9 hours
• To turn off the timer, press the timer button (M) repeatedly until display (D) shows

Changing between Fahrenheit and Celsius

• Press and hold the temperature button (L) on the control panel for 5 seconds
• Display (D) changes to show the desired setting
• Repeat the above steps to change back to the original setting

Changing between logs and crystals

WARNING Risk of burns!

• Some parts of this product can become very hot and cause burns Make sure the product has cooled down and/or off before changing the logs and crystals

Change the look of the product by removing the installed logs (B) behind the display panel (A)

1. Remove the display panel (A) as described in Installation B step 1
2. Continue with the below 2 steps to remove the screws and logs, then place the crystals (C) along the display edge evenly

Changing the Battery

1. Remove the battery holder from the remote control
2. Replace the used battery with a new CR2025 3 V battery The positive pole (+) must be pointing upwards

Cleaning and Maintenance

WARNING Risk of electric shock! To prevent electric shock:

1. For wall installation A: Set the power switch (F) to ‘0’ and remove the plug (G) from the socket outlet
2. For recessed installation B and C: Set the wall switch to off

Cleaning
NOTICE Clean the product regularly to prevent the build-up of hairs dust or lint around the heating vents (C), as this may cause the outlet to become blocked

• To clean the product, wipe with a soft, slightly moist cloth
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product
• Do not spray liquids directly onto any surfaces of the product

Maintenance

• Any other servicing than mentioned in this manual should be performed by a qualified service personnel?

Troubleshooting

socket outlet Check if the socket outlet works

t The product has overheated and the thermal safety device has activated Switch off the product and switch it back on after 10 minutes

The flame on display panel does not move| t Flame motor faulty Contact a qualified service personnel
The product switches off automatically| t The product has overheated and the thermal safety device has activated Switch off the product and switch it back on after 10 minutes
The remote control does not work| t Low battery Change the battery

t Standing too far from the product or an object is blocking the path Move closer or to a clearer path

t The product has not been switched on Switch on the product from the on/off switch (F) or connect to the socket outlet

Dim or poor visible flame or crystals are not glowing| t The product LED lights are burnt out or the wiring is loose Contact a qualified service personnel

Battery Disposal

Do not dispose of used batteries with your household waste Take them to an appropriate disposal/collection site

Specifications

• Model number: BLT-999W-13/42″
• Rated voltage: 120 V AC 60 Hz
• Power consumption: 1300 W
• Net weight: approx. 39.6 lbs (18 kg)
• Dimensions (W x H x D): approx. 42 x 19.8 x 4.7″ (106.6 x 50.2 x 11.9 cm)
• Model number: BLT-999W-13/50″
• Rated voltage: 120 V AC 60 Hz
• Power consumption: 1300 W
• Net weight: approx. 46.3 lbs (21 kg)
• Dimensions (W x H x D): approx. 50 x 19.8 x 4.7″ (127 x 50.2 x 11.9 cm)
• Model number: BLT-999W-13/60″
• Rated voltage: 120 V AC 60 Hz
• Power consumption: 1300 W
• Net weight: approx. 55.56 lbs (25.2 kg)
• Dimensions (W x H x D): approx. 60 x 19.8 x 4.7″ (152.4 x 50.2 x 11.9 cm)

Remote control

• Voltage/battery type: 3 V , 1 x CR2025 (Lithium)

Feedback and Help
We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan the QR Code below with your phone camera or QR reader:

If you need help with your Amazon Basics product, please use the website or number below.

amazon.com/gp/help/customer/contact-us
amazon.co.uk/gp/help/customer/contact- us

Product Dimensions

Installation Type

NOTICE A dedicated socket outlet must be installed inside the recessed wall opening. Keep at least 3.9″ (10 cm) spacing between the back of the product and a socket outlet. The socket outlet must be wired to an accessible 16 A double pole switch. Contact a professional electrician if in doubt.

NOTICE Avoid tension on extremely bent parts of the supply cord after plugging in. Lay out the supply cord properly before placing the product into the wal

NOTICE A dedicated socket outlet must be installed inside the recessed wall opening. Keep at least 3.9″ (10 cm) spacing between the back of the product and a socket outlet. The socket outlet must be wired to an accessible 16 A double pole switch. Contact a professional electrician if in doubt.

NOTICE Set the power switch to ‘I’ (product on) before fixing the product into the recessed wall opening.

CAUTION Risk of injury or product damage! Choose a location with a minimum of two wall studs capable to withstand the product’s weight
NOTICE Avoid tension on extremely bent parts of the supply cord after plugging in. Lay out the supply cord properly before placing the product into the wall

amazon.com/AmazonBasics
MADE IN CHINA

References

• Amazon Sign In
• Amazon Iniciar sesión
• Amazon Iniciar sesión
• Amazon Sign-In
• Amazon Sign-In
• Iniciar sesión en Amazon
• Iniciar sesión en Amazon
• Connexion Amazon
• Connexion Amazon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>