amazon basics 5524BC Electric Standing Desk Instruction Manual
- June 14, 2024
- amazon basics
Table of Contents
ELECTRIC
SIT-STAND DESK
Instruction Manual
5524BC Electric Standing Desk
Screwdriver is required during the installation please prepare it in advance.
Step 1
Align the holes of Left Leg (2) and Drive
Rod (4), using Wrench (M-F) to secure both with Screw (M-A).
Step 2 Insert Drive Rod (4) into the hole of Right Leg (3). If it cannot
be inserted tilt Right Leg (3) slightly until they’re matched.
Step 3 As shown, use Wrench (M-G), install Beam (1) to the Legs (2&3)
with Screws (M-B)6.
Step 4 Using Wrench (M-G), install Leg Base (6)2 to the Legs (2&3)
respectively with Screws (M-C)8.
Step 5 Using Wrench (M-G), install Side Plate (5)2 on each side of the
Legs (2&3) with Screws (M-B)4.
Step 6 Fix Boards (7a&7b) with Wooden Pin (14)4. Use screwdriver, with
Screws (M-D)10, install Desk Connection Plate (12)3 to the middle of the
Boards , and Desk Connection Hook (8)*2 to both sides of the Boards.
Step 7
Fix Silicone Sheet (16)10 to the corresponding hole position on
the Boards (7a&7b).
Step 8 Use screwdriver, secure the Leg part to the Boards (7a&7b) with
Screws (M-E)10. Please align the Silicone Sheet (16)10.
Step 9 As shown, connect the motor at the Left Leg (2), Hand Controller
(9) and Power Supply (10) in turn.
Step 10 Using screwdriver, install Hand Controller (9) to the Board (7a)
with Screws (M-D)2. Secure the connecting cable with Cable Clip (15)2 and
glue it to the bottom of the Board.
Step 11
Prepare the Drawer (11). Using
screwdriver, install it to the Board (7a) with Screws (M-E)4.
Step 12 Insert Cable Hole Cover (13)*2 into the hole in the Board (7b).
Using the Controller
Raise the Desk
Press the button to raise the desk continuously until it reaches the highest
position or the button is released.
Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest
position or the button is released.
Select Height Setting 1
Press the button, and the desk will move to the height that was previously set
for that button.
Select Height Setting 2
Press the button, and the desk will move to the height that was previously set
for that button.
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously
set for that button.
Save Current Height Setting
Short-press the button, and the screen will show ‘S-’ .Press the , , 3 or
button to save the current height setting to that button. When you press the ,
, or 3 button, the desk will move to the height that was previously set for
that button. Any button-press will stop the desk.
Settings
«Reset
Press and hold the button until ‘rst’ is displayed. Continue holding until the
desk goes down to its lowest level and comes back up slightly. Release the
button, and reset is complete. If the button is released during the reset
procedure, reset will stop. The desk won’t work until reset is done correctly.
¢ Child Lock
Press and hold the and buttons together for 5 seconds to turn child lock on.
The screen will show ‘LOC’ and the buttons will be disabled. Turn child lock
off the same way.
* Settings Menu
* Press and hold the & button for 5 seconds to enter the settings menu.
Short-press the button to navigate through the menu. Short-press the or button
to adjust the settings. Long-press the or button to quickly adjust the height
settings. Press and hold the button again to save the changes. ‘SUS’ will be
displayed if saving is successful (or ‘FAL’ if saving fails). If there is no
button-press for 10 seconds, the settings menu will be exited automatically.
Power-Saving Mode
The screen will turn off if there is no button-press for a minute. Any
button-press will turn the screen on again.
Protection Mode Error Codes**
SC0| Standby Overvoltage Protection: Standby voltage too high. Power off the
desk, check the connection between power
and the controller, and power on again. If error code persists, please contact
technical support.
---|---
SC1| Power Supply Overvoltage Protection: Input voltage too high. If the
correct AC adapter is being used, power off the desk,
check the connection between power and the controller, and power on again. If
error code persists, please contact
technical support.
SC4| Operating Overvoltage Protection: Operating voltage too high. Power off
the desk, check the connection between
power and the controller, and power on again. If error code persists, please
contact technical support.
hot| Overheating Protection: When the motor has been working continuously for
too long, it will stop operating to prevent
overheating. Wait for at least 18 minutes (until error code disappears) before
making any further height adjustment.
r-6| Power Supply Overvoltage Protection (during use): Input voltage too high.
Error clears when power supply voltage
returns to normal. If error code persists, please contact technical support.
rst| Reset Warning: Continue to complete reset.
E10| Short Circuit Protection: Power off, check the cable connections, and
power back on again. If error persists, please contact technical support.
E11| Overloading Protection: Max load exceeded. Error code will persist for 20
seconds (DO NOT operate). Take the things off
the desk and confirm there is no mechanical damage before trying again.
E12| Motor Phase Error Protection: Power off, check the cable connection
between the motor and the controller, and
power back on again. Then follow the reset instructions. If error code
persists, please contact technical support.
E13| Sensor Malfunction Warning: Motor sensor can’t be detected. Power off,
check the cable connection between the motor and the controller, and power
back on again. Then follow the reset instructions. If error code persists,
please contact technical support.
E14| Anti-Collision System Warning: Impact detected. The desk will move 2″
(50mm) in the opposite direction and stop.
E16| Cable Disconnection Warning: Check motor and controller cable
connections. Normal operation should return once all
connectors are properly connected. If error code persists, please contact
technical support.
E17| Mechanical Failure Warning: Check if there is any structural damage or
motor fault.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>