amazon basics B081244SRH Wall Mount Electric LED Multicolour 3D Heating Fireplace Instruction Manual

amazon basics B081244SRH Wall Mount Electric LED Multicolour 3D Heating

Fireplace

Product Information

• Product Name: Wall-Mount Electric LED Multicolor 3D Heating Fireplace with Remote Control
• Product Model Numbers: B081244SRH, B08124231H, B08123T2QK, B08298ZDKS, B0829BC1VY, B08298W63Y
• Quantity: 2 units
• Components:
  • A (x 1)
  • B (x 1)
  • C (x 1)
  • E (x 20)

Product Usage Instructions

1. Ensure that the space where the fireplace will be mounted is well insulated or suitable for occasional use.
2. Read the important safety instructions provided in the user manual and retain them for future reference.
3. Keep furnishings or other combustibles at least 1 meter away from the front, sides, and rear of the appliance to reduce the risk of fire.
4. Do not use the fireplace if the glass panel is damaged.
5. Avoid connecting the appliance to an external switching device or a circuit that is regularly switched on and off by the utility to prevent inadvertent resetting of the thermal cut-out.
6. Take extra caution when children or vulnerable people are present as the appliance can become very hot and cause burns.
7. Avoid covering the appliance with clothing or other materials to avoid overheating.
8. For wall installation (Type A), follow the installation instructions provided.
9. For recessed installation (Type B), follow the installation instructions provided.
10. Follow the battery warnings mentioned in the user manual:
    • Keep batteries out of reach of children to prevent ingestion and potential chemical burns.
    • Avoid short-circuiting batteries by keeping terminals away from each other, especially when loose batteries are stored with keys or other conductive materials.
    • Do not attempt to charge non-rechargeable (primary) batteries as it can cause internal gas and/or explosion.
    • Ensure correct polarity (+ and -) when inserting batteries to avoid short-circuiting or charging in reverse, which can lead to overheating, leakage, venting, rupture, explosion, fire, and personal injury.
    • Properly dispose of used batteries and keep them out of reach of children as coin/button cell batteries can be swallowed and pose a risk of chemical burns, perforation of soft tissue, and death.
    • Avoid heat exposure, welding, or soldering directly to a battery as it can cause leakage, venting, explosion, or fire.
    • Do not dismantle or take apart the battery as it can lead to exposure to electrolyte, heat, leakage, venting, explosion, or fire.

TOOLS REQUIRED

BOX CONTENT

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:

• WARNING Risk of fire!

  •  Keep power cords, drapery, furnishings or other combustibles at least 1 meter from the front of the appliance, and away from the sides or rear.
  • In order to avoid overheating, do not cover the heater. Do not place objects in contact with the heater.

• WARNING Risk of injury!
  The appliance must not be used if the glass panel is damaged.

• CAUTION Risk of fire!
  In order to avoid a hazard due to the inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• CAUTION Risk of burns!
  Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

• This symbol indicates that in order to avoid overheating, the appliance should not be covered with clothing or other material.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

• The installation of the heater should be carried out by trained personnel. If, during reassembly of the heater, a part of the thermal insulation shows damage or deterioration, it should be replaced by an identical part.

• Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the appliance is left operating and unattended.

• Do not operate the appliance with a damaged cord or plug, after the appliance malfunctions, has been dropped or damaged by any manner. Discard the appliance or return to qualified service facility for examination and/or repair.

• Do not use outdoors.

• This appliance is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the appliance where it may fall into a bathtub or other water container.

• The appliance must not be located immediately below a socket outlet.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

• Never use with an extension cord. Connect the appliance to a dedicated socket outlet.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the appliance.

• This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.

• Install and use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Connect to properly grounded outlets only.

• This product contains no user serviceable parts and requires little maintenance. Leave any servicing or repairs to qualified personnel only.

• The LEDs contained in this product are non-replaceable.

• For UK only: All the electrical installations must be done according to BS 7671.

For wall installation A:

• Always unplug the appliance when not in use.
• To disconnect the appliance, switch controls to off, then remove plug from outlet.
• Connect the power plug to an easily reachable socket outlet so that in case of an emergency, the appliance can be unplugged immediately. Pull the power plug out of the socket outlet to completely disconnect the appliance from the voltage.

For recessed installation B:
To completely disconnect the appliance, set the wall switch to off.

Battery Warnings

WARNING
KEEP OUT OF REACH OF CHILDREN
Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention promptly.

DANGER Risk of explosion!
Risk of explosion if the battery is replaced by an incorrect type.

• Keep batteries out of the reach of children. In particular, keep batteries which are considered swallowable out of the reach of children. In case of ingestion of a coin cell seek medical assistance promptly.
• Do not allow children to replace batteries without adult supervision.
• Always insert batteries correctly with regard to polarity (+ and -) marked on the battery and the equipment. When batteries are inserted in reverse they might be short-circuited or charged. This can cause overheating, leakage, venting, rupture, explosion, fire and personal injury.
• Do not short-circuit batteries. When the positive (+) and negative (-) terminals of a battery are in electrical contact with each other, the battery becomes short-circuited. For example loose batteries in a pocket with keys or coins, can be short-circuited. This can result in venting, leakage, explosion, fire and personal injury.
• Do not charge batteries. Attempting to charge a non-rechargeable (primary) battery can cause internal gas and/or heat generation resulting in leakage, venting, explosion, fire and personal injury.
• Do not force discharge batteries. When batteries are force discharged by means of an external power source the voltage of the battery will be forced below its design capability and gases will be generated inside the battery. This can result in leakage, venting, explosion, fire and personal injury.
• Exhausted batteries should be immediately removed from equipment and properly disposed of. When discharged batteries are kept in the equipment for a long time electrolyte leakage can occur causing damage to the equipment and/or personal injury.
• Do not heat batteries. When a battery is exposed to heat, leakage, venting, explosion or fire can occur and cause personal injury.
• Do not weld or solder directly to batteries. The heat from welding or soldering directly to a battery can cause leakage, venting, explosion or fire, and can cause personal injury.
• Do not dismantle batteries. When a battery is dismantled or taken apart, contact with the components can be harmful and can cause personal injury or fire.
• Do not deform batteries. Batteries should not be crushed, punctured, or otherwise mutilated. Such abuse can cause leakage, venting, explosion or fire and can cause personal injury.
• Do not dispose of batteries in fire. When batteries are disposed of in fire, the heat build-up can cause explosion and/or fire and personal injury. Do not incinerate batteries except for approved disposal in a controlled incinerator.
• A lithium battery with a damaged container should not be exposed to water. Lithium metal in contact with water can produce hydrogen gas, fire, explosion and/or cause personal injury.
• Do not encapsulate and/or modify batteries. Encapsulation of any other modification to a battery can result in blockage of the pressure relief mechanism(s) and subsequent explosion and personal injury. Advice from the battery manufacturer should be sought if it is considered necessary to make any modification.
• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Symbols Explanation

• This symbol stands for “Conformité Européenne”, which declares “Conformity with EU directives, regulations and appplicable standards”. With the CE-marking, the manufacturer confirms that this product complies with applicable European directives and regulation.
• This symbol stands for “United Kingdom Conformity Assessed”. With the UKCA-marking, the manufacturer confirms that this product complies with applicable regulations and standards within Great Britain.

Intended Use

• This product is suitable for providing instant heat to warm up a room and also for visual ambiance. It is not intended for use as a primary heat source.
• This product is intended for household use only. It is not intended for commercial use.
• This product must be wall or recessed mounted. IT IS NOT SUITABLE FOR USE AS A FREE STANDING APPLIANCE. Operating the product in any other position could cause a hazard.
• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.

Product Description

• A Display panel
• B Logs
• C Heating vents
• D Display
• E Touch controls
• F On/off switch
• G Power cord with plug
• H Wall mounting bracket
• I Inset mounting bracket
• J Ember colour button / SET
• K Ember lock button
• L Temperature button
• M Set day/time button
• N Increase button
• O Celsius/Fahrenheit button
• P Flame colour button / SET/OK
• Q Flame lock button
• R Power level button / SET+
• S Timer button
• T Decrease button
• U Standby button
• V Display

Before First Use

DANGER Risk of suffocation!
Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocation.

• Check the product for transport damages.
• Remove all packing materials including packaging inside the firebox behind the glass display panel (A) as described in installation B step 1.
• Before connecting the product to the power supply, check that the power supply voltage and current rating corresponds with the power supply details shown on the product rating label.
• Remove the protective strip on the remote controls battery compartment.

Installation tips

WARNING
Failure to install the product as instructed may result in damage to the product and or may expose the user to the risk of fire, electric shock, serious injury or death.

• This product should be installed and maintained only by an experienced adult. If in doubt, consult a professiona.
• Before mounting, determine the suitable mounting location. The product must be fixed to a wooden or masonry/concrete wall using fasteners that are appropriate for the mounting surface.
• Do not install on drywalls, wall boards or thin plywood. The mounting surface must be capable of supporting the weight of the product.
• For best results, install the product out of direct sunlight.
• To avoid reconstruction install the product in a proximity of properly grounded socket outlet.
• Do not drill into any pipes or power lines beneath the surface during mounting holes preparation. Use voltage/metal detector.
• The wall mounting bracket (H) is attached to the product when delivered. Remove the wall mounting bracket (H) before starting to install.
  For recessed installation B : The socket outlet must be wired to an accessible 16 A double pole switch in order to safely switch the product on/off.

Operation

Switching on/off

1. Connect the power cord with plug (G) to a suitable socket outlet.

2. Set the power switch (F) to ‘I’ (product on). The product beeps and the standby indicator stays lit. The product is now in standby mode.

3. Press the standby button (U) to switch on the product.
   NOTICE The display goes off approximately 7 seconds after no other button is pressed.

4. To switch off the product, press the standby button (U) again.

NOTICE

• Pressing any button on the remote or touch controls once, displays the current room temperature. To select any function, press the same button twice.
• There may be a trace of odor during the first few minutes of use, or after a period of storage. This is normal and quickly disappears.
• If the product is not in use for a long period:
  • For wall installation A : Set the power switch (F) to ‘0’ and remove the plug (G) from the socket outlet.
  • For recessed installation B : Set the wall switch to off.

Setting day and time

1. Press the set date/time button (M), the days indicator starts flashing.
2. Quickly press the increase button (N) or decrease button (T) to select the day, then press the set date/time (M) to confirm. The hours indicator starts flashing.
3. Quickly press the increase button (N) or decrease button (T) to select the hours, then press the set date/time (M) to confirm. The minutes indicator starts flashing.
4. Quickly press the increase button (N) or decrease button (T) to select the minutes, then press the set date/time (M) to confirm. The day and time is now set.

Setting temperature
NOTICE The product must be set to low or high power for the heating function to work.

• Press the temperature button (L) repeatedly until the desired temperature has been selected. Alternately, use buttons (N) and (T) to scale up or down the temperature range.
• The temperature range is between 17 – 30 °C (62 – 86 °F).
• When the room reaches the set temperature, the heating function stops automatically.
• If the product detects a drop in temperature, the heating function resumes automatically.

Changing power level

• Press the power level button (R) to cycle through the different settings. The display (V) show the below symbols to indicate the power level selected.

• The approximate heat coverage area with each power level:

  • Low Power – 8 – 10 m²
  • High Power – 10 – 20 m²
    NOTICE This product is fitted with a temperature limiting control. If the product reaches an unsafe internal temperature of 115 °C, the product automatically switches off. To reset, unplug the product from the socket outlet and wait 5 minutes before plugging it back in and switching on.

Changing flame colour

• Press the flame button (P) repeatedly until the desired colour is selected.
• The display (V) shows the code to indicate the colour selected.
• When using F0 mode, press the flame lock button (Q) at anytime to stop the loop. Press the flame lock button (Q) again to resume.
  • F1 Orange
  • F2 Orange and green
  • F3 Green
  • F4 Green and blue
  • F5 Blue
  • F6 Blue and orange
  • F7 Blue, orange and green
  • F8 Blue and red
  • F9 Red
  • F0 Loop through all colours

Changing ember colour

• Press the ember button (J) repeatedly until the desired colour is selected.
• The display (V) shows the code to indicate the colour selected.
• When using C0 mode, press the ember lock button (K) at anytime to stop the loop. Press the ember lock button (K) again to resume.
  • C1 Red
  • C2 Blue
  • C3 Green
  • C4 Rose red
  • C5 Orange
  • C6 White
  • C7 Purple
  • C8 Yellow
  • C9 Light blue
  • C0 Loop through all colours

Setting open window detection function
The product monitors the temperature of the room once it reaches the set temperature. If the room temperature drops by 5°C or more within 10 minutes, the product automatically stops heating to conserve energy.

1. Press and hold the SET/OK button (P) on the touch controls to activate this feature. The display shows E1 to indicate function is on.
2. Press and hold the SET/OK button (P) on the touch controls, then press the SET- button (J) to deactivate this feature. The display shows E0 to indicate function is off.
   • E0: Open window detection function off
   • E1: Open window detection function on

Setting timer

1. Press the timer button (S) to activate timer function. The timer symbol displays on the display (V) and the hours setting starts flashing.
2. Press the timer button (S) to skip through the days until you reach the desired day for setting. Each day which does not require timer function should be programmed as 00.00 for ON and OFF time for each period.
3. Once the desired day has been selected, press the increase button (N) or decrease button (T) to set the ON hours, press the timer button (S) to continue.
4. Press the increase button (N) or decrease button (T) to set the ON minutes, press the timer button (S) to continue.
5. Press the increase button (N) or decrease button (T) to set the OFF hours, press the timer button (S) to continue.
6. Press the increase button (N) or decrease button (T) to set the OFF minutes, press the timer button (S) to continue.
7. Press the timer button (S) on the product’s touch controls to activate timer function. The timer function symbol lights up on the display (D).

NOTICE

• Timer setting can only be done using touch controls (E).
• After setting the first period, the timer moves onto the second period allowing you to set the time again the same way.
• Repeatedly press SET/OK (P) to scroll through the days and periods.
• To clear an operational period, set the ON and OFF times to the same value.

Changing between Fahrenheit and Celsius
Press the Celsius/Fahrenheit button (O) repeatedly until the desired setting has been selected.

Changing between logs and crystals
Change the look of the product by removing the installed logs (B) behind the display panel (A).

1. Remove the display panel (A) as described in installation B step 1.
2. Continue with the below 2 steps to remove the screws and logs, then place the crystals (C) along the display edge evenly.

Changing the Battery

NOTICE

• Ensure that the batteries are installed correctly with regard to polarity (+ and -).
• Clean the battery contacts and also those of the equipment prior to battery installation.
• Remove exhausted batteries promptly.

1. Remove the battery holder from the remote control.
2. Replace the used battery with a new CR2025 3 V battery. The positive pole (+) must be pointing upwards.

Cleaning and Maintenance

WARNING Risk of electric shock!

• To prevent electric shock:
  • For wall installation A : Set the power switch (F) to ‘0’ and remove the plug (G) from the socket outlet.
  • For recessed installation B: Set the wall switch to off.

Cleaning
NOTICE Clean the product regularly to prevent the build-up of hairs dust or lint around the heating vents (C), as this may cause the outlet to become blocked.

• To clean the product, wipe with a soft, slightly moist cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.
• Do not spray liquids directly onto any surfaces of the product.

Maintenance
Any other servicing than mentioned in this manual should be performed by a qualified service personnel.

Plug fuse replacement (for UK only)

• Use a flat screwdriver to open the fuse compartment cover.
• Remove the fuse and replace with the same type (13 A, BS1362). Refit the cover.

Troubleshooting

• The product does not switch on.

  • Check if the power plug is connected to the socket outlet. Check if the socket outlet works.
  • The product has overheated and the thermal safety device has activated. Switch off the product and switch back on after 10 minutes.

• The product switches off automatically.
  The product has overheated and the thermal safety device has activated. Switch off the product and switch back on after 10 minutes.

• Flame on display panel does not move.
  Flame motor faulty. Contact a qualified service personnel.

• Remote control does not work.

  • Low battery. Change the battery.
  • Standing too far from the product or an object is blocking the path. Move closer or to a clearer path.
  • The product has not been switched on. Switch on the product from the on/off switch (F) or connect to the socket outlet.

• Dim or poor visible flame or crystals are not glowing.
  The products LED lights are burnt out or wiring is loose. Contact a qualified service personnel.

Disposal (for Europe only)

The Waste Electrical and Electronic Equipment (WEEE) laws aim to minimise the impact of electrical and electronic goods on the environment and human health, by increasing re-use and recycling and by reducing the amount of WEEE going to landfill. The symbol on this product or its packaging signifies that this product must be disposed separately from ordinary household wastes at its end of life. Be aware that this is your responsibility to dispose of electronic equipment at recycling centres in order to conserve natural resources. Each country should have its collection centres for electrical and electronic equipment recycling. For information about your recycling drop off area, please contact your related electrical and electronic equipment waste management authority, your local city office, or your household waste disposal service.

Battery Disposal

Do not dispose of used batteries with your household waste. Take them to an appropriate disposal/collection site.

Specifications

• Model number: BLT-999W-13/42″
  • Rated voltage: 220-240 V~, 50 Hz
  • Power consumption: 1300 W
  • Approximate heat coverage area Low Power – 8 – 10 m², High Power – 10 – 20 m²
  • Protection class: Class I
  • Net weight: approx. 18 kg
  • Dimensions (W x H x D): approx. 106.6 x 50.2 x 11.9 cm
• Model number: BLT-999W-13/50″
  • Rated voltage: 220-240 V~, 50 Hz
  • Power consumption: 1300 W
  • Approximate heat coverage area Low Power – 8 – 10 m², High Power – 10 – 20 m²
  • Protection class: Class I
  • Net weight: approx. 20 kg
  • Dimensions (W x H x D): approx. 127 x 50.2 x 11.9 cm
• Model number: BLT-999W-13/60″
  • Rated voltage: 220-240 V~, 50 Hz
  • Power consumption: 1300 W
  • Approximate heat coverage area Low Power – 8 – 10 m², High Power – 10 – 20 m²
  • Protection class: Class I
  • Net weight: approx. 24.8 kg
  • Dimensions (W x H x D): approx. 152.4 x 50.2 x 11.9 cm
• Remote Control
  • Voltage/battery type 3 V , 1x CR2025

Importer Information

• For US
  • Postal: 134248
  • Business Reg.: Amazon EU S.à r.l., 38 avenue John F. Kennedy, L-1855 Luxembourg
• For UK
  • Postal: 017427
  • Business Reg.: Amazon EU SARL, UK Branch, 1 Principal Place, Worship St, London EC2A 2FA, United KingdomBR

Feedback and Help

• Love it? Hate it? Let us know with a customer review.
• AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you to write a review sharing your experiences with the product.
  • amazon.co.uk/review/review‑your‑purchases#
  • amazon.co.uk/gp/help/customer/contact‑us

Energy Efficiency Information

DIMENSION

TYPE OF INSTALLATION

References

• Amazon Basics
• Amazon.de: Günstige Preise für Elektronik & Foto, Filme, Musik, Bücher, Games, Spielzeug & mehr
• Connexion Amazon
• Connexion Amazon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>