DMOO SPORTING D39 Air Conduction Bluetooth 5.3 Earphones User Manual
- June 13, 2024
- DMOO
Table of Contents
DMOO SPORTING D39 Air Conduction Bluetooth 5.3 Earphones User Manual
Functional description
- Touch: manually power on/off/pause/play/answer/hang up/move to previous and next music/enable SIRI
- LED indicator
- Call microphone
- charge the Earphone Copper Pole
- Indicator on the charging box
- Type-c charging port
Product Description
Bluetooth version: 5.3
Working temperature: 5″‘C ~ 40°C
Battery capacity: 65mA/h
Charging period: about 90 minutes
Total musical playtime: about 6hours (in moderate volume)
Chip type: JL7003
Audio decoding: AAC, SBC
Loudspeaker type: 1511 (MM) full-range compound titanium speaker
Frequency response: 2DHz-20KHz
Standby time: 20 days
Connection distance: 12m
Applicable devices: Bluetooth devices that support
HFP/A2DP/AVRCP/AVCTP protocols, such as mobile phones and
computers, to make calls and listen to music
Mobile charging box
Battery capacity of the charging box: 400mNh
Charging time: LSH
Input current: 5V\0.5A
Output current: SV\50mA/h (single)
Charging cycles: about 2.5 – 3
Details of Functions
Power on
This headset will be on automatically after opening the cover of the charging
box/ to manually power on it, please long press “Power” 3 seconds, with the
blue indicator always on for l S and a prompt t.one “Power on”, then, the
headset will enter automatic connection. If there is a device that has been
paired and connected with it nearby, it will be automatically connected back.
If there is no such device, the master earpiece will enter device pairing in
about 8 seconds automatically, with a prompt
tone “Pairing” and the indicator flashing in red and blue alternately.
Pairing with device
To pair with a device, please power on your mobile phone and enable
“Bluetooth”, refresh the device list to find out “D39” and then click it for
pairing. After successful connected, the headset will prompt •connected~, with
the blue indicator on both earpieces flashing every 5 seconds and the prompt
that “the headset is already connected” displayed on your mobile phone.
Factory reset
For factory reset in case of manual change of pairing settings (the pairing
has been completed in factory by default), please make 6 consecutive clicks to
restore no matter it is connected with Bluetooth or not, then, the red and
blue indicators begin to flash quickly (in pink). Next, connect to the device
you want as instructed above.
Power off
The headset will be off and charged automatically after it is put into the
charging box with its cover closed/ to power it off when it is on, please long
press “Power” Seconds to manually power it off (both the earpieces will be off
synchronously with manual
power-off); then, the red indicator will be on for 1S, with a prompt “Power
Off”.
Cautions
In case of any need to use one of the earpieces. just put the other one into
the charging box, and t he earpiece you want to use will be switched to
automatically, and act as the master one in subsequent use by default If you
need to use both earpieces. just
pick up the other one and make it connected automatically.
General features
Play/pause: when the music is playing, please double click the
master/secondary earpiece, with the blue indicator on both the earpieces
flashing every 5 seconds.
Next: when the music is playing, please gently touch the right earpiece 3
times, with the blue indicator on both the earpieces flashing every 5 seconds.
Previous: when the music is playing, please gently touch the left earpiece 3
times, with the blue indicator on both the earpieces flashing every 5 seconds.
Answer a call: when there is an incoming call, please touch once (both
earpieces operable), with the blue indicator on both the earpieces flashing
every 5 seconds.
Hang up: when you are on a call, please touch once (both earpieces operable),
with the blue indicator on both the earpieces flashing every 5 seconds and a
prompt toneou”.
Reject a call: when there isan incoming call, touch for consecutive 2 seconds
(both earpieces operable), with a prompt tone MDu”.
EnableSiri: long press 2seconds (both ea pieces operable) when the headset is
connected with your mobile phone to enable Siri; to disbare Siri, long press 2
seconds again.
Disconnect device: disable “Bluetooth on your mobile phone to make the master
earpiece enter the pairing mode, with the red and blue indicators on it
flashing alternately.
Automatic connection: afterthecharging box is opened, it will be connected
automatically to the last device connected previously. If the device is not in
the range of connection, the master earpiece will enter the pairing mode in 8
seconds automatically.
Low battery prompt: it well beep for low battery when the voltage is
below3.3V.
Automatic shutdown: it will be off automatically if no device is connected in
5 minutes or the battery voltage is below 3.2V.
Status of indicators on the headset
Power on: the headset will be on after the blue LED indicator stays on for 1
seconds.
Power off: the headset will be off after the red LED indicator stays on for 1
seconds.
Pairing: the red and blue LED indicators on both earpieces flash alternately.
Waiting for connection with a device: the red and blue LED indicators on the
master earpiece flash alternately.
Standby state after successful connection with a device: after successful
connection, the L/R blue indicator flashes every seconds.
On a call: the LJR blue indicator flashes every Seconds.
Status of indicators on the charging box
- During charging: after inserting the USB charging cable to power on, the 4 Indica tors turn on and run around, with the current battery level displayed for 5 seconds. When the battery level is within 0%~25%,all the other three indicators will be off, except indicator 1 that will flash slowly. When the battery level is within 25%- 50%, both the indicators 3 and 4will be off, with the indicator 2 flashing slowly and the indicator 1 always on; when the battery level is within 50%~75%, both the indicators land 2 will be always on, with the indicator4 off and the indicator 3 flashing slowly; when the battery level is within 75%~ 100%, all the three indicators will be always on, except the indicator 4 flashing slowly; when the battery level reaches 100%, all the indicators, together with the white light, will be always on;
- During charging the headset (without any external charger): after closing the cover of the charging box, the current battery level will be displayed for 5 seconds, and then it begins to charge the L/Rear pieces. Indicators on the far left and the far right indicate the states of the L/R earpieces respectively. Both the indicators will be always on during charging, and turn off after fully charged.
- Fully charge the charging box (with a cable): the white indicator in four bars will be always on.
- Current battery level: the current battery level of the charging box will be displayed for 5 seconds after its cover is opened.
- Low battery: the indicator will flash quickly with only the last bar turning en (every 0.5S), and the headset will keep alarming before it enters the low voltage protection mode.
Steps of Operation
Please fully charge the headset before each use, and make sure the battery of
the device or mobile phone to be used with the headset is also in a high
level.
Then, power on the headset, and make it enter the pairing mode (with the red
and blue indicators on the master earpiece flashing alternately) and close to
the mobile phone to be connected for pairing.
Power on your mobile phone and enable “BT”, then, dick the search button to
search for the device and click it for connection.
After successful connection in several seconds, the blue indicator on both
earpieces will flash every 5 seconds, and your mobile phone will display that
the devkit has been connected.
Both t he earpieces will work normally when you make calls and listen to music
with your mobile phone.
Attentions
Please don’t drop, hit, scratch, twist, beat, roll or throw the headset into
water;
Please keep the headset away from magnets, electrical appliances and speakers
when using it;
Please try to avoid placing the headset in extreme temperatures (ambient
temperature range: -S’C~40″C);
Please don’t expose the headset to moisture.
Non-warranty Ordinance
- The shell of the product is damaged, not to be returned for scraping;
- Damage caused by force majeure;
- Product pressure loss, water immersion, the shell knock damage, deformation and other artificial damage;
- Unauthorized Maintenance, to the product itself changes, without permission to remove the headphone body and its accessories;
- The performance failure of this product is caused by man-made re.:1sons.
Note: The above non-warranty ordinance we have the right to refuse to deal with.
After-sales service and support
Xiang bizi bluetooth headset after-sales service commitment strictly in accordance with the ( Consumer rights and interests protection law of the Peoples Respublika: of China) , (Product quality law of the People’s Republic of China) implementation of after-sales three commitments service, service content as follows:
During the validity period of the three commitments service, you can enjoy the right to repair, replace and return goods according to this regulation.
- Within 7 days from the day after you sign for the product, the product performance failure, after-sales service center testing confirmed that can enjoy return, replacement or repair services;
- Within 15 dar-; from the day after you sign for it, if the product has a performance failure, After-sales service center testing confirmed that can enjoy replacement or repair services;
- In case of performance failure of this product within 12 months from the day after you sign for it; After-!iales service center testing confirmed that can enjoy repair services; if there is a demand for after-sales service, please contact customer service.
Manufacturer: Hangzhou YUehan Network Technology Co., Ltd.
Manufacturer: Hangzhou Xiang biz, Technology Co., Ltd.
Production address: No. 368, Liuhe Road, Binjiang District, Hangzhou City,
Zhejiang Province, Haichuang base.
Customer service number: 400-863-3833
Website: wwwxiangbizi.com
FCC caution
Documents / Resources
| DMOO
SPORTING D39 Air Conduction Bluetooth 5.3
Earphones
[pdf] User Manual
2AQ9R-D39, 2AQ9RD39, d39, SPORTING D39, SPORTING D39 Air Conduction Bluetooth
5.3 Earphones, Air Conduction Bluetooth 5.3 Earphones, Bluetooth 5.3
Earphones, Earphones
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>