feelfree KAYAKS 2023 EZ Rider Seat Lumbar Support Installation Guide
- June 13, 2024
- feelfree KAYAKS
Table of Contents
LUMBAR SUPPORT
INSTALLATION INSTRUCTIONS.
LUMBAR SUPPORT PART LISTS
(1) (2)
(3) (4)
(5) (6)
M6x40 M6x60
(7)
NO
| PART NUMBER| DESCRIPTION| QTY
---|---|---|---
1| 8858687352545| HUNG SEAT LUMBAR SUPPORT|
1
2
| 3101040162000| LUMBAR TOP RAIL SILDER CONNECTOR| 1
3| 2101080131000| LONG BUSH|
2
4
| 50071| SCREW TH STL M4x15| 2
5| 50057| SCREW JT STL M6x40|
2
6
| 50142| SCREW JT STL M6x60| 2
7| 2101080159000| SHORT BUSH|
2
LUMBAR SUPPORT INSTALLATION MANNUAL
1.INSTALL LUMBAR BOTTOM FRAME WITH BACKREST FRAME.
- WASHER
- SCREW M6 X40
NOTE:
1. ADD THE SHORT PLASTIC BUSH WHEN INSTALL WITH THE MOKEN 10 V.2 / MOKEN12.5
V.2 / SEASTREAM ANGLER 120 / SEASTREAM ANGLER 120 PD / BIGFISH 105 V.2 / FLASH
PD BACKREST FRAME.
2. ADD THE LONG PLASTIC BUSH WHEN INSTALL WITH THE BIGFISH 103 / 108 / 120
V.2 / JONNY BACKREST FRAME.
3. FOR THE MOKEN 10 LITE V.2 / MOKEN 10 PDL NOT USE THE PLASTIC BUSH.
- WASHER
- SCREW M6X40 / SCREW M6x60
- LONG BUSH(BF103,108,120 V.2/JONNY)
- SHORT BUSH (MK10V.2,12.5 V.2/SS ANGLER 120,120 PD)
2 INSTALL LUMBAR TOP FRAME WITH LUMBAR BOTTOM FRAME.
NOTE 1: ADJUST LEVEL OF THE TOP FRAME FOR FIT WITH THE BACKREST FRAME BAR.
2.DRILL 3.0 MM HOLE AND SCREW THE LUMBAR BOTTOM FRAME TOGETHER WITH LUMBAR TOP FRAME.
3.TIGHTEN THE ADJUSTER CORD.
4.INSTALL THE BUNGEE.
4 HOW TO ADJUST THE LUMBAR SUPPORT TO UP AND DOWN POSITION
– TURN THE ADJUST KNOB TO CLOCKWISE DIRECTION FOR ADJUST THE LUMBAR SUPPORT TO DOWN POSITION.
– TURN THE ADJUST KNOB TO COUNTERCLOCKWISE DIRECTION FOR ADJUST THE LUMBAR SUPPORT TO UP POSITION.
5. HOW TO ADJUST THE LUMBAR SUPPORT FRONT AND BACK POSITION.
– TURN THE LUMBAR PROTUDE ADJUST KNOB TO CLOCKWISE DIRECTION FOR ADJUST THE LUMBAR SUPPORT TO FRONT DIRECTION.
– TURN THE LUMBAR PROTUDE ADJUST KNOB TO COUNTERCLOCKWISE DIRECTION FOR ADJUST THE LUMBAR SUPPORT TO BACK DIRECTION.
LUMBAR SUPPORT TIPS
1.CHANGE THE BACKREST PAD WHEN INSTALL THE LUMBAR SUPPORT WITH OLD HUNGSEAT BACKREST FRAME.
OLD BACKREST PAD NEW BACKREST PAD
2.TAKE OFF THE OLD BACKREST PAD FROM BACKREST FRAME.
3.PUT THE NEW BACKREST PAD COVER THE BACKREST FRAME.
4.TIGTHEN THE ROPE FOR MAKE THE BACKREST PAD FIT WITH THE BACKREST FRAME.
5.TIGTHEN THE STRAP FOR HOLD THE BACKREST PAD.
LUMBAR SUPPORT TIPS
- MAKE SURE ALL NUTS AND BOLTS ARE TIGHT.
- MAKE SURE UNIT IS RINSED WITH WATAR AFTER USE DO NOT USE A PRESSURE WATER.
- MAKE SURE THE UNIT IS COMPLETELY DRY BEFORE STORING.
- ALWAYS STORE IN A DRY PLACE, PREFERABLY.