SM21 Wonderfoot Kit for Qnique Instruction Manual
- June 12, 2024
- WonderFoot
Table of Contents
Copyright November 5, 2021
Grace Company
(Reproduction Prohibited)
Version 1.2
Parts & Tools
| Wonderfoot (ACC-09-15216)
---|---
| LENS A –
Stitch In the Ditch (ACC-05-15206)
• Trace seams and lines
| LENS B –
1/4” Offset (ACC-05-15208)
• Echoing and offset lines
| LENS C –
3/8” Offset (ACC-05-15207)
• Echoing and offset lines
| LENS D –
1/4” Circle (ACC-05-15211)
• Echo and offset curves
| LENS E –
Clear (ACC-05-15210)
• Clear view of needle area.
| LENS E – Clear (ACC-05-15210)
• Clear view of needle area.
| Hopping
Foot Height Tool (SMP-04-12171)
• Set hopping foot height for quality stitching.
| Hopping
Foot Height Tool (SMP-04-12171)
• Set hopping foot height for quality stitching.
| Standard
Hopping Foot (SMP-04-10057)
• Replace the old standard hopping foot on your machine.
| SHCS M3 x 8
mm (x2) (2 pre-installed) (HDW-03-10966)
• Set hopping foot height for quality stitching.
IMPORTANT: READ FIRST
The standard hopping foot installed on your machine may not match the standard hopping foot found in this kit.
If this is the hopping foot on your machine, go to “Upgrading the Hopping
Foot” on page 8.
If this is the hopping foot on your machine, go to “Lens
Swapping Instructions” on page 12.
Upgrading the Hopping Foot
-
Use a 3 mm Allen wrench to remove the screw attaching the hopping foot to the hopping foot
collar on your machine.
-
Remove the needle bar thumb screw and carefully pull out the needle.
-
With a 3 mm Allen wrench, loosen the hopping foot collar screw just enough so that the collar can be pulled off the machine.
-
Slide the new hopping foot collar that came with this kit onto the press bar. Hold in place with the hopping foot collar screw.
-
Place the new standard hopping foot onto the hopping foot collar bar. Attach with a hopping foot screw loosely enough that the hopping foot can slide
up and down.
-
Reinstall your machine’s needle and needle thumb screw.
-
Slowly lower your needle.
-
Slide the height tool under the foot, and tighten the hopping foot screw with a 3 mm Allen wrench.
Lens Swapping Instructions
Foot
Installation Instructions
- Raise the needle.
- While holding the needle in place, remove the needle bar thumb screw.
- Hold the needle in place, and loosely attach the M3 x 4 mm thumb screw that came with the Wonderfoot.
- Use the needle magnet that came with your machine to align the needle, and tighten the thumb screw.
- Remove the standard hopping foot with the 3 mm Allen wrench.
- Loosely install the Wonderfoot.
- Slowly lower the needle.
- Slide the height tool under the foot.
- Make sure the height tool is underneath the Wonderfoot wheel.
- Tighten the hopping foot screw with the 3 mm Allen wrench.
- When moving your machine onto the fabric, slide the inside circlet of the hopping foot away from the fabric edge.
- Practice with the provided templates! Templates can be printed off www.graceframe.com on the Wonderfoot page.
The Grace Company
Phone: 1-800-264-0644
www.graceframe.com
Documents / Resources
|
WonderFoot SM21 Wonderfoot Kit for
Qnique
[pdf] Instruction Manual
SM21 Wonderfoot Kit for Qnique, SM21, Wonderfoot Kit for Qnique, Kit for
Qnique, for Qnique, Qnique
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>