FondVision Q10-C/Q Dynamic QR Code Standalone Controller User Manual
- October 30, 2023
- FondVision
Table of Contents
Dynamic QR Code Standalone Controller
Q10-C/Q
Q20-C/Q
Manual
Q10-C/Q Dynamic QR Code Standalone Controller
Note:Q20-C/Q and Q10-C/Q difference:Q20-C/Q with keypad,Q10-C/Q non-
keypad. Q20-C/Q with keypad have password door opening function.
Q20-C/Q and Q10-C/Q the Scanning QR code and RFID Card usages, installation,
wire connection, size, packing completely the same, the following contents
take Q20-C/Q as an example.
Products introduction
Q20-C/Q is our independent research and development production, good
performance QR code+RFID Card Standalone controller .Advanced CMOS image
recognition technology, intelligent image recognition system, scan code
recognition rate of high speed, large capacity s torage (10,000 user card
information), high security, simple operation, comple te functions, dynamic QR
code
APP+ card + password three ways to open the door
Products picture
Parameter
Dynamic QR Code Standalone Controller Q20-C/Q
Products Features
Electrical parameters
Appearance and
packing
Working environment
| communication| Offline
Management| 6 digit Password （Q10-C/Q non-keypad no this function）
App| Quicklopen
Reading card type| MF Card
Reading Range| MF:1～3cm，QR Code:1～20cm
Card Capacity| ≥10000 cards
Door opening mode| App,Card,Password（Q10-C/Q non-keypad no this function）
Prompt mode| Buzzer sound, Blue work light on, green light flashes
Camera pixel| 300000 pixels
Scan resolution| 640*480
Reading angle| Rotate 360 °, tilt ± 45 °, deflection ± 45 °
Keypad Type| Press| （Q10-C/Q Non-keypad）|
Open door time| 0～99s
Door ell function| with Doorbell button（Q10-C/Q no Doorbell keypad）
Work voltage| DC12V
Work current| 100mA
Color and material| Black| Plastic ABS|
Size| 120×80×18（mm）
Install hole space| 60 mm
Packing list| （Dynamic QR Code Standalone Controller 、8P wire、manual）×1
Working
temperature
| -10~60℃
Working humidity| 5%-85%
8P Socket Wire connection
| Wire S/N| Color| | Interface| Illustrate
1| Red| | DC12V| Cathode
2| Black| | GND| GND
3| Yellow| | NC| Relay NC
4| White| | COM| COM
5| Black| | NO| Relay NO
6| Green| | OPNE| Exit button
7| Yellow| BEEP|
Doorbell
8| Blue| BEEP
Electric lock wire diagram
We suggest use dedicated access control power supply, output relay signal that
directly drives electrical locks, automatic doors, gates, etc
QR Code Standalone Controller LED status
| illustrate | Blue/Green | Green light | Buzzer |
|---|---|---|---|
| Work Status | on | ||
| Programming mode | on | ||
| Program mode sub-menu | on | ||
| Scan unregistered card on | Long sound di | ||
| Scan registered card | Blue light and green light are at | on | 2 short sound -di |
di”
After scan card need input password open door| interval flash
Card+Password mode| Blue/Green Flash every 0.5 second|
Password mode| Blue/Green Flash every 0.5 second|
Press keypad| | short sound di
Setting Successfully| | 2 short sound di di
Setting failure| | | Long sound di
Invalid input| | | Long sound di
Alarm| | | Continuous sound “di di di
Appearance structure size
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>