SeeNERGY INCASSO BASE SLIM Kitchen Extractor Hood User Manual

KITCHEN EXTRACTOR HOOD
INCASSO BASE SLIM

USER’S MANUAL

Dear customer!
Thank you for choosing the products of the brand “SEENERGY”. We put our best efforts so you were satisfied with your choice.

GENERAL INFORMATION

1.1 Prior to installing the extractor hood carefully read our recommendations, following which will provide safe work of the appliance. Save this User’s manual, as it contains  answers to the questions which may arise later.
BEFORE STARTING THE OPERATION (SWITCHING ON) THE APPLIANCE MUST BE HELD AT THE ROOM TEMPERATURE FOR AT LEAST TWO  HOURS.
1.2. This appliance is intended for extraction of polluted air from the space above the cooking appliance, and intended for domestic use and the household environment only  and meets the requirements of State Standard of Ukraine DSTU IЕС 60335-2-31:2006.
USE OF THE APPLIANCE IN GOALS OTHER THAN DOMESTIC IS FORBIDDEN. THE RISK OF INJURY AND PROPERTY DAMAGE INCREASES IN  CASE OF USE OF THE EXTRACTOR HOOD WITH PURPOSES OTHER THAN INTENDED, WHAT WILL LEAD TO WARRANTY CANCELLATION/
1.3. Use of the extractor hood decreases the content of harmful products of incomplete combustion of natural gas, as well as odors produced during cooking in the air, and  prevents pollution of walls, ceiling, and furniture with grease and soot.
1.4. The appliance is an air purifying device of the exhaust type with a diameter fan (turbine), completed with a grease picking aluminum filter (included) and has the option  of upgrading with a carbon odor filter. It is manufactured from sheets of carbon steel with a decorative protective coating of powder paints – 520/700 mm in width.
1.5. Depending on the installation scheme over the cooker, the extractor hood can work in two variants:
– in the mode of air extraction into the stationary ventilation shaft (chimney) of the kitchen using corrugated aluminum or plastic air-ducts Ø150mm or Ø120mm (see item  5.3);
– in the recirculation mode (closed circular air circulation in the kitchen), when the extractor hood is not connected to chimney, and the air is passed through aluminum grease  filter (included) and smothering carbon filter and is returned to the kitchen (see paragraph 5.3).
1.6. Attention! Do not start extractor hood installation before connecting it to electricity network and checking its technical serviceability, and checking all of its functions.
1.7. We recommend that all installation works, connection, and repair of your extractor hood should be carried only by qualified specialists professionally engaged in the  execution of such works.
1.8. The manufacturer does not bear responsibility for any damages and failures, caused by incorrect installation, operation, and repair of the extractor hood.
1.9. The manufacturer reserves the right to modify the product in order to improve its quality and technical specifications.
1.10. Technical specifications for the extractor hood are indicated in this manual and on the label attached to the inner surface of the body (access to it opens when the filter  is removed).
Attention! The extractor hood should be installed on the wall at the distance of 650-750mm above the electric cooker and at the distance 750-850 mm above the gas cooker.

MAIN TECHNICAL SPECIFICATIONS

mm)
279 (700 mm)
Overall dimensions of the extractor hood, mm| Width| 520 / 700
Depth| 270
Height| 155
Connection size of ventilation duct, mm| 0150 / 0120
Weight, kg| 4,6 (520mm)
5,0 (700mm)
Noise level, dB 63,0 (520mm)| 63,0 (700mm)
Protection class| I
Operation mode| S1 (long-lasting)
Electro cable type| Armored and grounded

PARTS SUPPLIED

HOOD DESCRIPTION

5.1 Kitchen range hood “INCASSO BASE SLIM” is an air-purifying device of hood type with a diametric ventilator (turbine) and is equipped with a grease- trapping aluminum filter. The product is manufactured in nonmotor version with a width of 520 or 700mm of sheet of carbon steel with decorative and protective coating of powder paints. 5.2 The hood is of the “built-in” type and is built into the kitchen furniture above the stove. 5.3 Depending on the installation scheme, the hood works in two variants (Pic. 1 / Pic. 2):  in the air outlet mode of the kitchen chimney (Pic. 1); in recirculation mode (closed circular air circulation in the kitchen) (Pic. 2).

“It should be borne in mind that when the hood is switched on indoors, the pressure is automatically reduced, which shall be offset by the flow of fresh air. This can be  achieved by opening doors, windows or equipment of special tidal ventilation.”
5.4 The hood consists of the following components (Pic. 3):

1. body
2.  pipe adapter (from Ø150 to Ø120)
3.  power cord
4.  switch of modes of work of hood (mechanical)
5.  decorative panel
6.  aluminum grease-trapping filter (5 layer)
7.  lighting lamps

INSTALLATION INSTRUCTIONS FOR THE HOOD

6.1 Select the operating mode and installation place of the hood.
6.2 Remove the hood from the packing box.
6.3 Connect the hood to the electricity mains and check all its functions.
It is recalled that the height of the hood installation above electric stoves should be at least 650mm, and above the gas stoves – at least 750mm (Pic. 1).
6.4 With regard to the established height and the condition of the hood fitting to the bottom of the lower shelf of hinged furniture cabinet, place and cut a rectangular  opening according to the dimensions of the mounted part of the hood (Pic. 4/4.1) according to the previously made paper template.

6.5 In order to secure the hood to cabinet, it is recommended to use 4 self- tapping screws 4.8×13 DIN968 (Pic. 4.2) from the middle of the hood (Pic. 4 ABCD openings)  (self-tapping screws are not included).

6.6 If necessary, install an air duct adapter (Ø150 x 120mm) on the hood adapter.
6.7 If the hood is operating in the mode of air outlet into the chimney, install the air duct of selected diameter according to the instructions, ensuring that it is airtight.
6.8 If the hood is in recirculation mode, no air duct is required. A carbon odor filter (should be bought separately) is required to install.
6.9 Check the reliability of the hood mounting, plug and connect the power cord to the socket.
For additional protection against voltage drops, it is recommended to connect the hood via an optional 6A automation circuit breaker.

INSTRUCTIONS FOR USE AND CARE OF THE HOOD

7.1 The hood has 3 ventilation speeds. Depending on the amount of evaporation in cooking, you can choose low, medium or high level of ventilation.
7.2 Before cooking, switch on the hood in the required operating mode. It is recommended to continue the work of the hood for 3-5 minutes after cooking, so that the air in  the kitchen will be cleared of residual evaporation and odors.
7.3 Switch of mode select buttons and switching on of lightning lamps is placed on the lower panel of body (Pic. 5):

1. low speed,
2. average speed,
3. high speed,
4. fan is off.

The touch switch with the symbol of the light bulb, intended to turn on the lamp at insufficient illumination of the working area of the cooker:
0 – light is off,
I – light is on.

7.4. Attention! Before cleaning the extractor hood, disconnect it from the electricity.
7.5. Use a damp cloth soaked in warm water with a neutral detergent for external cleaning of the painted extractor hood.
7.6. Never use abrasive detergents, coarse sponges or detergents containing soda, acid, chlorides or solvents to clean the extractor hood.
7.7. When cleaning, avoid getting moisture on the current-carrying parts of the extractor hood, and wipe the surfaces with a soft cloth after washing.
7.8. The aluminum filter, holding oil and dust from the air, is clogged and should be washed after being soaked in hot water with an effective detergent once every 1.5 to 2  months. Changing the color of the filter after washing does not affect the quality of its work.
7.9. To remove the aluminum filter, press the spring latch and remove the filter from the panel. Install the filter in reverse order.

Do not install the filter after washing until it is completely dry.
7.10. The carbon filters, used during recirculation mode should be changed every 3-6 months depending on the extractor hood use. Filters are installed on the T-like stab of  the cover of the turbofan by axial pushing and clockwise rotation.
7.11. LED lamps are installed on the extractor hood for lighting the working area of the cooker. Before starting lighting lamps substitution, disconnect the extractor hood  from electricity, and leave the lamps to cool. To replace the lamp, remove the aluminum filters, push the holder of the cartridge so that the lamp came out of the body of the extractor hood and remove it by turning it counterclockwise. Replace it with the new one with the same characteristics and install filters.

Picture 6. Replacement of the lighting lamp.
Picture 7. Aluminum filter removing.

ELECTRICAL SCHEMATIC DIAGRAM

Electrical schematic diagram of the sensor extractor hood «INCASSO BASE SLIM»

POSSIBLE MALFUNCTIONS OF THE EXTRACTOR HOOD

| Check connection to the electricity supply.| Check whether the display is turned on.| Check the lamp switch (should be turned on).| Check aluminum filter (should be cleaned once every 1.5-2 months).| Check the socket (For the power connection).| Check lamps.| Check air outlet pipe (for the traction).| Check carbon filter (replacement once every 34 months).
---|---|---|---|---|---|---|---|---
Extractor hood| | | | | | | |
The lamp does
not light.| | | | | | | |
Reduced performance of the extractor hood.| | | | | | | |
The extractor hood began to work louder.| | | | | | | |
Air is poorly drawn in the recirculation mode.| | | | | | | |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>