AUDIOFOCUS VENU 8 Active Full Range Loudspeakers User Manual

June 1, 2024
AUDIOFOCUS

AUDIOFOCUS VENU 8 Active Full Range Loudspeakers

AUDIOFOCUS VENU 8 Active Full Range Loudspeakers

MANUFACTURER DECLARATIONS

Safety standards

AUDIOFOCUS® is a Trademark of COMMUNITY EUROPE S.A

Rue du Polissou, 17
B-5590 Achêne
Belgium

Community Europe S.A is in conformity with the provisions of the following EC Directives, including all amendments, and with national legislation implementing these directives:

  • 2014/35/EU
  • 2014/30/EU

Voltage regulations.
Electromagnetic Compatibility Directive RoHs Directive The following harmonized standards are applied:

  • EN 55103-1:2009,
  • EN 55103-1:2009/A1:2012
  • EN 55103-2:2009
  • EN 61000-3-2:2014
  • EN 61000-3-3:2013
  • EN 61000-3-11:2000
  • EN 62368-1:2014
  • EN 62368-1:2014/AC:2015

Specified characteristics are measured and given the following standard:

  • EN 60268-5

Speakers, rigging and accessories follow Machinery Directive:

  • 2006/42/CE with a static test coefficient of 7.

This manual is intended for information purposes only, is subject to change without notice, and cannot be used as a commitment by Community Europe S.A.

Operation

Important safety instructions are indicated by the following symbol to attract your attention:

  • Read and keep these instructions.
  • Follow this manual and its instructions.
  • Keep the device away from water and moisture.
  • Keep the device away from heat sources of any kind.
  • Only use accessories which have been tested and approved by AUDIOFOCUS.
  • Pay attention to the correct application and maximum load capacity of the accessories as detailed in our specific “Mounting instructions” or in our “Flying system and rigging manuals”.
  • Ensure that all additional hardware, fixings and fasteners used for installation or mobile deployment are of an appropriate size and load safety factor.
  • Pay attention to the manufacturers’ instructions and to the relevant safety guidelines.
  • Regularly check the loudspeaker condition and accessories for visible signs of wear and tear, and replace them when necessary.
  • Regularly check all load bearing bolts in the mounting devices.
  • Powered devices must be electrically grounded and connected through a circuit breaker and residual current circuit breaker. National or local electrical standards (such as IEC) should be respected.

Tips that could help you use the speaker more efficiently are indicated by a tip symbol:

Symbol External usage temperature should be between 0°C and 45°C.
Humidity should be 90% non-condensing maximum. Storage temperature -20°C to 70°C.

Sound levels

Symbol VENU series loudspeakers can deliver high sound pressure levels that could permanently damage the hearing of production crew, artists and audience members. Do not stay in close proximity to loudspeakers when in use. Check and obey all applicable laws and regulations regarding maximum sound levels and length of exposure.

SYSTEM DESCRIPTION

Introduction

Thank you for choosing an AUDIOFOCUS VENU Series full range 2 way point source speaker.
This user manual contains essential information for deploying VENU 8, VENU 12 or VENU 15 elements to their full capability. Read this document carefully to become familiar with the system.
Whether you are using 2 elements or 24, as floor monitors, adjustable angle pole mounted or rigged, we are sure you will find the VENU to be a highly versatile addition to your professional sound reinforcement inventory or fixed installation.
Since point source loudspeakers cannot sum coherently in the way true line source arrays do (especially in the higher frequencies), they are best used in single box or small arrays that are focused on discrete listening areas to minimize comb filter effects.
All VENU series cabinets are made from Birch plywood for rock solid construction and are shaped in anisometric hexagonal designs to allow for use as stage monitors if necessary. They feature powder coated steel grills.
For precise aiming and control, and to ensure as little high frequency overlap as possible, all VENU 12 and VENU 15 loudspeakers are equipped with a rotatable wave guide.
To keep costs down in budget-conscious applications, AUDIOFOCUS offers the VENU series in active, bi-amp passive and single channel passive versions.
VENU 8 is only offered in active or single channel passive versions.

VENU SERIES RANGE

VENU 8 Series

VENU 8 is a versatile, full range, 2-way point source speaker with a great power to size ratio. VENU 8 fits a broad range of applications, such as small PA, monitors or distributed installation. It can be used on a pole as a FoH speaker or with an additional subwoofer, making it suitable for sound reinforcement applications spanning small scale concerts, public places or theaters where sound quality is crucial.
VENU 8 houses an 8” LF driver and a 1’’ HF exit driver with a conical 80° waveguide.

VENU 8 Series
VENU 8 Series

VENU 12 Series

VENU 12 is a versatile, full range, 2-way point source speaker. The VENU 12 is the workhorse of the series and can be used for many different applications due to its power to size performance, such as small PA, monitors or distributed installation.
It can be used on a pole as a FoH speaker or with an additional subwoofer, making it suitable for applications spanning small scale concerts, public places or theaters where sound quality is crucial.
VENU 12 houses a 12” LF driver and a 1’’ HF driver mounted on a rotatable 110°x60° waveguide.

VENU 12 Series
VENU 12 Series

VENU 15 Series

VENU 15 is a versatile, full range 2-way point source speaker. It is the largest product of the series. VENU 15 fits a broad range of applications, such as medium PA, monitors or distributed installation. It can be used on a pole as a FoH speaker or with an additional subwoofer, making it suited to applications spanning small scale concerts, public places or theaters where sound quality is crucial.
VENU 15 houses a 15” LF driver and a 1’’ HF driver mounted on a rotatable 110°x60° waveguide.

VENU 15 Series
VENU 15 Series

Additional Low End

S 15 and S 18

VENU series speakers can be used with the S 15 or S 18 subwoofer, pole mounted.*

Additional Low End

MTSub 218

VENU series speakers can be used with the MTSub 218 subwoofer.*

Additional Low End
Additional Low End

S 21

VENU series speakers can be used with the S 21 subwoofer.*

Additional Low End

  • Note : for easy and accurate set up, all Venu series speakers are time and phase aligned to the sub series when fronts are aligned in a stacked configuration using Audiofocus presets.

Accessories

Symbol The official VENU rain cover will protect the speaker from rain and direct sun radiation without affecting the sound quality of the unit.

ACCESSORIES| NAME PRODUCT CODE| WEIGHT|
---|---|---|---
| Vertical Yoke for VENU
Ref. : 47100 (VENU 8)
Ref. : 47102 (VENU 12)
Ref. : 47103 (VENU 15)| 5 Kg|
| Horizontal Yoke for VENU
Ref. : 47820 (VENU 8)
Ref. : 47822 (VENU 12)
Ref. : 47823 (VENU 15)| 6 Kg|
| Rain Cover for VENU
Ref. : 47108 (VENU 8)
Ref. : 47111 (VENU 12)
Ref. : 47110 (VENU 15)| 0.3 Kg|
| Protection Cover for VENU
Ref. : 47299 (VENU 8)
Ref. : 47301 (VENU 12)
Ref. : 47302 (VENU 15)| 0.2 Kg|
| Touring flightcases for VENU
Ref.: 47112 Flightcase for 2 VENU 8(a) without wheels
Ref.: 47114 Touring Flightcase for 2 VENU 12(a) incl. wheels
Ref.: 47115 Touring Flightcase for 2
VENU 15(a) incl. wheels| |

Official VENU series flight cases protect your investment and can prolong speaker life.

SELF-POWERED (A) VERSION SETUP

Connections

AUDIOFOCUS power and audio cables with the appropriate diameter, length and connectors are recommended. OPERATING VOLTAGE must always stand between 90 and 264V. The power supply will auto switch between 110V or 230V, allowing the device to be used internationally without additional settings.

Symbol AC POWER DISTRIBUTION must be properly grounded and on the same network for the entire sound system. Bad grounding could result in unwanted noise and security issues for users and audience.

PowerCON True 1 TOP Connection

Each VENU module has two powerCON TRUE1 TOP connectors. Each link cable must be able to manage the whole linked system and its diameter will then follow this total power need.

Symbol Always consider a 500W, @ 230V power rating power when calculating the maximum possible number of devices to be linked.

A maximum of 8 VENU speakers can be linked thru the powerCON TRUE1 connector on a 230V 20A mono line with a 2.5mm2 diameter. AUDIOFOCUS originals cables are recommended.

Symbol Amplifiers can reach temperatures as high as 70°c.

User interface

User interface

Presets color scheme

Preset Color Description
Full Range Red The standard preset, for a standalone system
X-over Green Same curve as the Full Range but with a HP filter at 80 Hz to

be used with an additional sub.
Monitor | Blue| Same curve as the Full Range preset, but with a compensation EQ to reduce the floor coupling effect.

  1. Status LED
    • solid Green for OK Status
    • blinking Green in start up mode
    • Red for temp warning or limit.
  2. XLR 3-point IN and THRU
  3. Preset switch. Press and hold until LED starts blinking. While blinking, toggle between presets. After a few seconds the preset is loaded and the LED glows solid.
  4. Preset type indicator LED
  5. Serial Number
  6. PowerCON TRUE1 and powerCON TRUE1 link
  7. Micro USB connector for factory preset updates.

BI-AMP & X- VERSION SETUP

Amplifier configuration

All AUDIOFOCUS cabinets can be powered by any of the AUDIOFOCUS A Series rack amplifiers with integrated DSP. Each preset includes all crossover, frequency and phase response correction, along with RMS and peak protection on each channel to protect the speaker from damage or misuse. AUDIOFOCUS can also supply Powersoft Armonia presets on request.

AUDIOFOCUS A Series Amplification Chart

Product| Channels Used| A-354
#Per circuit| A-354
#Per amp| A-704
#Per circuit| A-704
#Per amp| A-1504
#Per circuit| A-1504
#Per amp| A-3004
#Per circuit| A-3004
#Per amp
---|---|---|---|---|---|---|---|---|---
VENU 8X| 1| 1| 4| 2| 8| 4| 16| 4| 16
VENU 12X| 1| 0| 0| 1| 4| 2| 8| 4| 16
VENU 15X| 1| 0| 0| 1| 4| 2| 8| 4| 16
VENU 12| 2| 0| 0| 2| 4| 2| 4| 4| 8
VENU 15| 2| 0| 0| 2| 4| 2| 4| 4| 8

Combinations of different speakers and / or subs are also possible.
Please check the sub series amplification chart from the sub series manual.

NL4 Connector detail Bi-amp Version

NL4 Speaker Polarity
1+ LF +
1- LF
2+ HF +
2- HF

NL4 Connector detail Bi-amp Version

NL4 Connector detail X-amp Version

NL4 Speaker Polarity
1+ Input +
1- Input
2+ Thru +
2- Thru

NL4 Connector detail X-amp Version

NL4 Connector detail X-amp Version

KIT en rendu:

KIT A – 1 amp, 4 x 4 VENU
KIT B – 2 amps, 2 x VENU Top, 2 x S 15 sub, 4 x 3 VENU monitor
KIT C – 3 amps 2 x VENU top, 2 x S 15 sub, 6 x 4 VENU monitor (2 per 2)

Symbol Make sure to load the appropriate preset! Loading the wrong preset could damage the speakers.

Connections

AUDIOFOCUS power and signal cables with the appropriate diameter, length and connectors are recommended. OPERATING VOLTAGE must always be between 90 and 264V. The power supply will auto switch to 110V or 230V, allowing the device to be used internationally without additional settings.

Symbol AC POWER DISTRIBUTION must be properly grounded and on the same network for the entire sound system. POWER DISTRIBUTION must be well balanced.

On a TETRA installation, each line (1, 2 and 3) will power the same number of devices.
Each device will be powered between a line and neutral and all devices will be connected to the same ground.

Connections

If you are not using an official AUDIOFOCUS cable kit, make sure to use the appropriate cable diameter and check the connection scheme.

Preset handling

Venu series presets are available for both Audiofocus A-series and Powersoft amplifiers.
Please refer to the corresponding Audiofocus Scio or Powersoft Armonia manual for more details regarding preset loading and operation.

USER GUIDELINES

Stacking and rigging

Symbol All local and national regulations should be complied with.
Refer to qualified technicians for rigging and deployment.
Only use original AUDIOFOCUS parts for rigging.
Chain hoists and any other third-party devices should be rated to match the weight of the system and cables.
Long term installations should be inspected regularly.

Stacking

VENU series speakers can be used stacked or pole mounted.

VENU stacked on S15 as monitor

VENU Stacked in front fill on 2 MTSub218

VENU pole mounted on S15

Stacking

VENU series speakers are equipped with an adjustable angle speaker stand socket, allowing you to change the vertical angle of the cabinet. Angle adjustable up to +/- 13.05º in 4.5º steps.

VENU on speaker stand

Stacking

VENU on speaker stand with adjustable tilt angle base

Stacking

Adjustable tilt angle base

Rigging

For information about rigging the install version, please refer to VENU install rigging manual.

Rigging

VENU Horizontal bracket

VENU eye bolt

Maintenance

VENU series speakers are protected by a Polyurea coating with a UV treatment to ensure extended system life and high shock resistance.
All speaker protection systems mentioned earlier will ensure an extended life.
If the cover becomes wet, remove it and allow it to dry. If cleaning is required, do not use aggressive cleaning products on synthetic parts.
Regularly check the condition of the cabinet.
Polyurea parts can be cleaned with furniture maintenance products. Metal parts can be cleaned with a microfiber cloth.

TECHNICAL SPECIFICATIONS

VENU 8a

Type
2-way active full-range point source
(self-powered version only)
Drivers
LF: 1×8’’
HF: 1×1’’
Frequency range -6dB
55Hz-20kHz
Power handling Watt AES/Peak, active and install version
LF: 350/1400W
HF: 80/320W
Nominal Impedance, active and install version
8ohm
Passive cross-over network
SPL Peak @ 1m pink noise Crest factor 5dB
134 dBSPL
Presets
Dedicated AUDIOFOCUS and Armonia/Powersoft omni and cardio presets
Self-powered audio Connectors
IN: 1×3-point XLR
LINK: 1×3-point XLR
Bi-amp connector
2x SPK4 speakON
Self-powered power Connectors
IN: 1×3-point powerCON TRUE1
LINK: 1×3-point powerCON TRUE1
Dimensions (h x w x d)
430 x 275 x 290 mm/ 16,77×10,82×11,41 inches
Weight following version
Self-powered: 11,5kg / 25,35lbs
Passive: 10,1kg / 22,26lbs
Finish
Highly resistant polyurea coating
Material
First grade birch plywood 15 & 24 mm

VENU 8 Horizontal beamwidth

Technical Specifications

VENU 8 Vertical beamwidth

Technical Specifications

VENU 12a

Type
2-way active full-range point source
(self-powered verion only)
Drivers
LF: 1×12’’
HF: 1×1’’
Frequency range -6dB
50Hz-20kHz
Power handling Watt RMS/Peak, active and install version
LF: 350/1400W
HF: 35/140W
Nominal Impedance, active and install version
8ohm
Passive cross-over network
SPL Peak @ 1m pink noise Crest factor 5dB
135 dB
Presets
Dedicated AUDIOFOCUS A-series SCiO and Powersoft Armonia presets
Self-powered audio Connectors
IN: 1×3-point XLR
LINK: 1×3-point XLR
Bi-amp connector
2x SPK4 speakON
Self-powered power Connectors
IN: 1×3-point powerCON TRUE1
LINK: 1×3-point powerCON TRUE1
Dimensions (h x w x d)
566 x 362 x 357 mm • 22.28 x14.25 x14.05 inches
Weight following version
Self-powered: 18.5kg / 40.78lbs
Passive: 17.3kg / 38.13lbs
Finish
Highly resistant polyurea coating
Material
First grade birch plywood 15 & 24 mm

VENU 12 Horizontal beamwidth

Technical Specifications

VENU 12 Vertical beamwidth

Technical Specifications

VENU 15a

Type
2-way active full-range point source
(self-powered verion only)
Drivers
LF: 1×15’’
HF: 1×1’’
Frequency range -6dB
47Hz-20kHz
Power handling Watt RMS/Peak, active and install version
LF: 400/1600W
HF: 35/140W
Nominal Impedance, active and install version
8ohm
Passive cross-over network
SPL Peak @ 1m pink noise Crest factor 5dB
136 dB
Presets
Dedicated AUDIOFOCUS A-series SCiO and Powersoft Armonia presets
Self-powered audio Connectors
IN: 1×3-point XLR
LINK: 1×3-point XLR
Bi-amp connector
2x SPK4 speakON
Self-powered power Connectors
IN: 1×3-point powerCON TRUE1
LINK: 1×3-point powerCON TRUE1
Dimensions (h x w x d)
638 x 426 x 412 mm • 25.11 x 16.77 x 16.22 inches
Weight following version
Self-powered: 22.5kg / 49.60lbs
Passive: 17.3kg / 38.13lbs
Finish
Highly resistant polyurea coating
Material
First grade birch plywood 15 & 24 mm

VENU 15 Horizontal beamwidth

Technical Specifications

VENU 15 Vertical beamwidth

Technical Specifications

Need more informations about our products ?
www.audiofocus.eu
info@audiofocus.eu
www.facebook.com/AudiofocusPage/
www.facebook.com/groups/AUDIOFOCUS/

Scan QR Code to view the AUDIOFOCUS website.

Follow Us.

Social Media Icons

Logo

Documents / Resources

| AUDIOFOCUS VENU 8 Active Full Range Loudspeakers [pdf] User Manual
VENU 8 Active Full Range Loudspeakers, VENU 8, Active Full Range Loudspeakers, Full Range Loudspeakers, Range Loudspeakers, Loudspeakers
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals