KINGBOLEN K7 Modular Comprehensive Automotive Diagnostic Tool User Manual
- June 12, 2024
- KINGBOLEN
Table of Contents
KINGBOLEN K7 Modular Comprehensive Automotive Diagnostic Tool
Product Information
- Product Name: KINGBOLEN
- Product Type: Device with licence-exempt transmitter(s)/receiver(s)
- Compliance: Complies with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s)
- Operating Conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Product Usage Instructions
- Safety Precautions:
- Do not modify or alter the software of the device.
- Follow all instructions provided in the user manual to ensure safe usage.
- Do not use the device if it is damaged or shows signs of malfunction.
- Installation :
- Place the device on a stable and flat surface.
- Ensure that there is sufficient ventilation around the device to prevent overheating.
- Connect the necessary cables and power source as indicated in the user manual.
- Operation:
- Power on the device using the designated power button.
- Follow the on-screen instructions or refer to the user manual for initial device setup.
- Familiarize yourself with the device’s interface and features by exploring the user manual.
- Interference Handling:
- If the device causes interference to other devices, adjust its placement or orientation to minimize interference. –
- If the device experiences interference from other sources, move away from those sources if possible.
- If interference persists, contact customer support for further assistance.
- Maintenance:
- Keep the device clean and free from dust and debris
- Avoid exposing the device to extreme temperatures or humidity.
- Regularly check for firmware updates and install them as recommended by the manufacturer.
Note: The information provided here is a summary of the user manual. For detailed instructions and specific guidelines, refer to the complete user manual provided with the product.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio rrv technician for help.
FCC WARNING
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End user must follow the specifific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter.
The mobile device is designed to meet the requirements for exposure to radio
waves established by the Federal Communications Commission (USA). These
requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The
highest SAR value reported under this standard during product certification
for use when properly worn on the body
is 1.364 W/kg.
For body operation, this device has been tested and meets FCC RF exposure
guidelines when used with any accessory that contains no metal and that
positions a minimum of 0mm from the body. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
IC Requirement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation , Science and Economic Development
Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
For body operation, this device has been tested and meets IC RF exposure
guidelines when used with any accessory that contains no metal and that
positions a minimum of 0mm from the body. Use of other accessories may not
ensure compliance with IC RF exposure guidelines.
All LE-LAN devices contain security features to protect against modification
of software by unauthorized parties.
Product Overview
- Bluetooth Diagnostic Dongle: Green: device is powered on, blue: Bluetooth is connected, red: there is a fault code.
- Touch Screen: 7 inches (1280*720).
- On/Off key: Long press to switch on/off, click to rest the screen.
- Charging Port: TYPE-C charging port & development system debugging USB port.
- Camera: Support 1300W pixel camera for taking pictures.
Connect the KINGBOLEN K7 with your vehicle through the OBDII port
Usually, the OBD port is located under the dashboard, above the pedal on the driver’s side. The five locations shown lite the picture are common OBDII port locations.
Turn on the KINGBOLEN K7
After connecting with the car, the screen will display as shown in the picture.
Connect Wi-Fi 
The system will automatically search all available Wi-Fi networks and you can choose the “Wi-Fi” needed. Notice the “Wi-Fi” must be set before use.
Activate diagnostic Dongle
Please enter the SN number and activation code of the connector and click Activate.
Tip: The activation code can be found on the password letter.
Functions Description
The KINGBOLEN K7 main unit has the following 9 functions:
-
Scan:
This module has auto search (automatic scanning of car models’ VIN), car model lists, Demo (demonstration of the diagnosis process), History (diagnosis records), OBD&IM (9 emission-related module diagnosis) -
OBD:
Support OBD II and EOBD protocols after 1996. -
Module:
Support external module, e.g. TPMS
Tip: Please upgrade the firmware in “Settings-Firmware Fix”
Activate Sensor
This function allows users to activate TPMS sensor to view sensor data such as
sensor ID, tire pressure, tire frequency, tire temperature and battery
condition. For universal sensors, place the tool by the alongside of the stem,
point toward the sensor location, and press the OK button. Once the sensor is
successfully activated and decoded, KINGBOLEN K7 will vocally announce that
the sensor is activated and the screen will display the sensor data.
Notes:
- For early magnet-activated sensors, place the magnet over the stem and then place the TPMS module accessorg by the alongside of the stem.
- If the TPMS sensor requires tire deflation (about I OPSI), then deflate the tire and place the TPMS modle accessorg by the alongside of the stem while pressing the OK button.
Repeat this step to check other vehicle sensors. After all sensors are
successfully activated, the following interface will appear. 
Program Sensor
This function allows users to program sensor data to kingbolen sensors to
replace faulty sensors that are with low battery capacity or not functioning.
The following options are available for programming kingbolen sensors:
Automatically Create (Auto), Manually Create (Manual) and Copy ID by
Activation (Replication).
Auto: This function is designed to program kingbolen sensors by applying
random IDs, created according to the test vehicle when it is unable to obtain
the original sensor IDs. Select the wheel which needs to be programmed, place
a kingbolen sensor close to the TPMS antenna of the tool, and select “Auto” to
create a random sensor ID.
Manual: This function allows users to manually input sensor ID. Users can
input a random ID or the original sensor ID if it is available.
Replication: This function allows users to write in the retrieved
original sensor data to the kingbolen sensor. It is used after the original
sensor is activated.
Programming steps:
- Place a kingbolen sensor close to the TPMS antenna of the tool
- Select the wheel (FL, FR, RL, RR) that the sensor is to be installed in
- Select the programming method (Auto, Manual, Replication)
- Click “Programming”
The programming process normally takes in 1 minute, and it would vocally announces the programming result, with sensor data displayed on the screen after it completes.
Relearn Sensor
This function allows users to check and view the detailed TPMS sensor relearn
procedures. Relearn operation applies only when the newly programmed sensor
IDs are different from the original sensor IDs stored in the vehicle’s ECU.
Relearn is used to write the newly programmed sensor IDs into the vehicle’s
ECU for sensor recognition.
Reset: Supports the most common multiple maintenance and reset functions,
it involves in 28 reset functions, there are shown as follows: Maintenance
Light Reset
(OIL); Steering Angle Reset (SAS); Battery Matching (BMS); ABS Exhaust (ABS);
Throttle Matching (ETS); Brake Pad Reset (EPB); DPF Regeneration (DPF); Anti
theft Matching (AFS); Injector Coding (INJEC); Tire Pressure Reset (TPMS); Sus
pension Level Calibration (SUS); Headlight Matching (AFS); Gearbox
Matching(Gearbox); Sunroof Initialization (SUN); EGR Adaption (EGR); Gear
Leaming (Gear); ODO Reset (ODO);
Airbag Reset (Airbag); Transport Mode (Transport); A/F Reset (A/F); Stop/Start Reset (Stop/Start); NOx Sensor Reset (NOx); AdBlue Reset (Diesel Engine Exhaust Gas Filter) (AdBlue); Seat Calibration (SeatS); Coolant Bleeding (Coolant); Tyre Reset (Tyre); Windows Calibration(Windows); Language Settings (Language).
Store: Display related products, please contact the dealer if necessary.
Module: It involves 4 functional modules shown as follows.
- PRINTER — Thermal printer for diagnostic reports. (with professional PRINTER thermal printing paper)
- Endoscope — HD video endoscope module.
- Battery tester — battery tester module.
- ScopeBox — oscilloscope module.
Note: Please purchase the 4 functional modules from the Store.
Repair Info:
Coverage lists: Quickly check the models and functions supported by the
current device. Learning: Videos contain guidelines for equipment use,
maintenance, and diagnostics. Video: The learning course demonstrates how to
operate the tool. User Manual: Help technicians quickly grasp the usage of
equipment and efficiently improve diagnostic capabilities.
File:
It is used to record and establish the files of the diagnosed vehicles. The
files are created based on the vehicle VIN and the check time, including all
diagnostic related data such as diagnostic reports, data stream records and
screenshots.
Setting:
Common system settings can be made here to modify and add information.
Settings
You can do some basic set up in this page. Include Wi-Fi, screen brightness, language, time zone, and so on.
- Feedback: You can feedback the diagnostic software/app bugs to us for analysis and improvements.
- Update: This module allows you to update the diagnostic software & App and set up frequently used software.
- Screenshots: Turn on this switch to take a screen capture.
- Screen floating window: Turn on this switch to record the screen operation video.
- Network: Set the connectable Wi-Fi network.
- Firmware fix: Used to update the firmware.
- Language: Select the tool language.
- Time zone: Choose the time zone of the current location, then the system will automatically configure the time according to the time zone you chose.
FAQ
Here we list some common questions and answers related to this tool.
Q: Why does it have no responses when connected to a vehicle?
A: Check whether the connection with the vehicle diagnostic port is proper,
whether the
ignition switch is on, and whether the tool supports the vehicle.
Q: Why does the system stop while reading the data stream?
A: This may be caused by loose diagnostic connection. Please unplug the
connector
and reconnect it firmly.
Q: Communication error with vehicle ECU?
A: Please confirm:
- Whether diagnostic connector is correctly connected.
- Whether ignition switch is ON.
- If all checks are normal, please send vehicle year, make, model and VIN number to us by Feedback function.
Q: Why does the screen flash when the engine ignition starts?
A: It is normal and caused by electromagnetic interference.
Q: How to upgrade the system software?
A:
- Start the tool and ensure a stable Internet connection.
- Go to “Settings”-> “App Update”, click “OTA” and then click “check version” to enter the system upgrade interface.
- Complete the process by following the instructions on the screen step by step. It may take a few minutes. After successfully completing the upgrade, the tool will automatically restart and enter the main interface.
Warranty Terms
This warranty applies only to users and distributors who purchase KINGBOLEN K7 products through normal procedures. Provide free warranty within one year. KINGBOLEN TECH warrants its electronic products for damages caused by defects in materials or workmanship. Damages to the equipment or components caused by abusing, unauthorized modification, using for non-designed purposes, operation ina manner not specified in the instructions, etc.are not covered by this warranty. The compensation for dashboard damage caused by the defect of this equipment is limited to repair or replacement. KINGBOLEN TECH does not bear any indirect and incidental losses. KINGBOLEN TECH will judge the nature of the equipment damage according to its prescribed inspection methods. No agents, employees or business representatives of KINGBOLEN TECH are authorized to make any confirmation, notice or promise related to KINGBOLEN TECH products. Service Line: (+86)0755-23445106
Customer Service
Email: support@kingbolen.com
Official Website: www.kingbolen.com
Youtube: Kingbolen auto scanner center
Facebook: @kingbolen.fans
Instagram: @kingbolen.fans.
Products tutorial, videos, FAQ and coverage list are available on kingbolen official website
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>